tapping temperature 中文意思是什麼
tapping temperature
解釋
出鋼溫度- tapping : n. 輕敲（聲）。n. 1. （開孔）導出液體。2. 【醫學】穿刺抽液；放腹水。3. 【冶金】出鋼；出鐵；出渣。4. 【電學】抽頭，分支，分流。5. 【機械工程】攻螺絲。
- temperature : n. 1. 溫度，氣溫。2. 體溫。3. 〈口語〉發燒，高燒。
-
The influences of furnace charges, chemical composition, quality of vermicularizing alloy, holding duration after vermicularizing treatment and tapping temperature on percentage of vermicular graphite were discussed
摘要討論爐料、化學成分、蠕化劑質量、處理后包內保留時間和溫度對蠕墨鑄鐵蠕化率的影響。 -
When the surface temperature and central temperature of slab is high enough, tapping timely is the crux of guaranteeing slab quality and energy saving
在同時保證鋼坯表面溫度和內部溫度的情況下，適時出鋼是既保證鋼坯加熱的質量又節省燃料的關鍵。 -
According to numerical simulation and molten steel solidification mechanism, in the paper, the restrict relationship had been setup between casting speed and molten steel level and average mould tapping section thickness as well as its shell temperature at tapping spout
本文基於數值模擬和鋼液凝固機理，建立起結晶器內鋼液液位和鑄坯拉速對其出鋼口處鋼液截面平均溫度和坯殼溫度的制約關系。 -
Eight of input and state variables of blast furnace, i. e. silicon content, irregular coke charge, coal injection, blast pressure, blast temperature, blast volume, batch of charge in a tapping period, ratio of ore - to - coke in charge, are considered as input of prediction model
採用天津鐵廠1 #高爐的[ si ]含量、鐵間料批數、熱風壓力、實際噴煤量、冷風流量、熱風溫度、凈焦加入量、焦炭負荷等8個影響因素作為預測模型的主要輸入變量。 -
Abstract : to analyze the temperature of the ladle completely and control it reasonably, the temperature drop behaviors of the molten steel in the ladle under various conditions were studied through establishing a proper mathematical model. the results provide a theoretical basis for reducing the temperature drop and decreasing the tapping temperature of the molten steel in the converter ， and for formulating proper temperature system of the liquid steel
文摘:為全面分析，併合理控制鋼包溫度，通過建立合理的數學模型，對鋼包熱行為進行模擬，分析了不同情況下鋼液的溫度下降行為.為減少鋼液溫降、降低出鋼溫度、合理制定鋼包溫度制度提供了一定的依據 -
Additions of carbon for improved slag resistance. spinel formation improves hot strength, slag resistance and brick joint erosion. 3 repairing material for bof uses fused magnesia or sintered magnesia as the main raw material and after modifid pitch and special additives are added, it has the following characteristcs than other conventional converter pitch temperature, shorter sintering time, longer service life and less pollution. it is mainly used for repairing converter working face, also for tapping side, tapping hole and bottom
3 ，轉爐大面補料是採用電熔鎂砂或燒結鎂砂為主要原料，通過加入改性瀝青和特種添加劑使它和傳統瀝青補爐料相比具有高溫附著性好燒結時間短流動性好使用壽命長污染小等特點，主要用於修補轉爐迎鋼面通常稱「大面」也可以用於修補出鋼側，出鋼口及爐底等部位。 -
The simulation results show that the system relationship model can reflect dynamic variation on its shell temperature and predict indirectly the shell thickness at tapping spout
模擬結果表明，所建立的關系模型能夠反映結晶器出鋼口處坯殼表面溫度的動態變化，及間接地預知坯殼厚度目的。 -
If a means of sealing the shell tapping is provided, it shall be suitable for the full pressure / temperature rating of the valve
如果提供了用於密封筒形絲錐的工具，這個工序必須適用於閥門所有壓力/溫度等級。
分享友人