thickness tolerance 中文意思是什麼
thickness tolerance
解釋
厚度負偏差-
Door leaves - height, width, thickness and squareness - tolerance classes
門扇.長度，寬度，厚度和方度.公差等級 -
In order to solve the problems made by the manual strong acid cleaning, such as the deformation and thickness tolerance of part, pollution problem, expensive cost and low production efficiency
摘要為了解決銅及銅合金手工強酸清洗存在的問題，如工件變形和厚度一致性差、環境污染大、成本高及生產效率低等問題，研究了銅及銅合金的自動化清洗生產方式、處理流程和工藝配方。 -
Three - dimensionally braided structural composites have distinct structure that is fully integrated, continuously spatial fiber - network impregnated with ductile material. the new innovative materials have not plies as conventional composites have, and put an end once and all to low interlaminar strength showing in laminate materials. because of their enhanced stiffness and strength in the thickness direction, near - net - shape design and manufacturing, superior damage tolerance and specified aerospace function, the braided composites are gaining more and more attention of industry and academia
三維編織結構復合材料是完全整體、連續、多向的紡線（纖維束）的網路，充填以延性材料，這類新材料已失去通常復合材料的層合板概念，由此，層合板復合材料層間脆弱的致命弱點在編織結構復合材料中得到克服，所以編織結構復合材料具有高的強度和剛度（包括在厚度方向） ，接近實際形狀的製造，高的沖擊韌性、高的損傷阻抗，和按實際設計要求的特定的航空航天方面的使用功能，因而廣泛地受到工業界和學術界的關注。 -
Thickness tolerance of hot - rolled sheet
熱軋鋼片厚度公差 -
The repair effect was compared with various type of repair parameters such as patch thickness young ' s modulus and thickness young ' s modulus of adhesive layer. in the chapter iv, a thermalstatic mechanical loading analysis of the repair problem was made. for the single side repair, the patch material having the maximum mismatch in the coefficient of thermal expansion with that of the crack aluminum plate provides the better damage tolerance capability for single - side crack in the panel
模擬計算表明：粘膠模量增大， j積分值降低，修補效果與粘膠模量有關；隨著粘膠厚度的增大，修補模型的j積分值略有增大后再逐步減小，應合理選擇粘膠的厚度，盡量避免選擇j積分較大值時的粘膠厚度；隨著補片厚度的增加，修補模型的j積分值逐漸增大，到達一定量后又開始減小，因此補片的厚度需要合理選擇。 -
Thickness tolerance of steel plate of pipe
鋼板或鋼管厚度負偏差 -
Thickness tolerance of electrolytic cold - rolled sheet
電解冷軋鋼片厚度公差 -
1 a set of 20 - rool mill with four vertical posts wv20seh55 - 300 1150 introduced from german sundwig. the mill may yearly produce 80, 000 tons of various markings of cold - rolled stainless steel, silicon steel, and carbon steel sheets with 0. 1 mm in thickness and 0. 01 in tolerance
1德國引進森德威wv20seh55 - 3001150四立柱式廿輥軋機一臺套，年產量8萬噸，該設備可生產成品最薄厚度至0 . 1mm的各種牌號的冷軋不銹鋼硅鋼普碳鋼板，公差可達到0 . 01mm 。 -
Door leaves - height, width, thickness and squareness - tolerance classes ; german version en 1529 : 1999
門扉.高度寬度厚度和面積.公差級 -
Aluminium alloy sheet. tolerance on total surface thickness
鋁合金板材.整個表面厚度公差 -
Tolerance on outer diameter and wall thickness should be observed, but for the following two circum stances, shorter axis should not be less than 95 % of nominal diameter
管材的不圓和壁厚不勻，應不超出外徑的壁厚允許偏差，但屬下列兩種情況之一者，其短軸尺寸應不小於公稱外徑的95 % 。 -
Analysis and measurement of the thickness tolerance in radiographic testing
射線檢測厚度寬容度的分析與測定
分享友人