throttle change 中文意思是什麼
throttle change
解釋
油門位置變化-
In this experiment, adjusting the throttle to the specific position, and letting engine rotary speed change from the lowest to the highest, at the same time, the data of the water temperature, the fuel temperature, the air press and the rotary speed can be noted. moreover, we can measure the fuel quantity and the ignition angle
實驗中，調節節氣門在特定位置，並讓發動機的速度依次從最低變化到最高，同時記錄水溫、油溫、進氣壓力和轉速等數據，還可以測出相應的噴油量、點火提前角。 -
This paper offers a method that can avoid the incorrect or rough methods mostly accepted now, and this method considers the temperature change along pipeline, the difference of friction loss in turbulence zone and the throttle effect in cross - section of reduced pipe
針對現有的靜態模擬演算法存在的錯誤和不足，提出了一種更為精確的模擬演算法，該演算法除考慮了管道沿線的溫度變化、處于不同的紊流區摩阻損失的大小不同之外，還考慮了變徑管道在變截面處存在節流效應等問題。 -
Accorded to the experimental research, under different flow area of flow valve and different adjusted pressure of relief valve, conclusion that the regulation of the pressure p1, p2 in the two cylinder chambers varied with the change of step load were as follows : when the throttle valve was series - connected on the return oil - line in the metering - out control system, under the same flow area and the same adjusted pressure of relief valve, with the incremental quantity of step load, the pressure highly - adjusted capacity of the hydraulic cylinder chamber with piston - rod decreased, meanwhile, it ' s time of rise, time to peak and the governing time all decreased. while the pressure highly - adjusted capacity of the hydraulic cylinder chamber without piston - rod increased
通過試驗研究得出系統在不同的流量閥開度、不同溢流閥調節壓力（進口壓力）下，液壓缸兩腔壓力p _ 1 、 p _ 2隨階躍負載變化的規律：當出口節流調速系統的回油路上串接節流閥時，隨階躍負載的增加，在相同流量閥開度、相同溢流閥調節壓力的情況下，液壓缸有桿腔壓力p _ 2 （ t ）的超調量是減小的，上升時間、峰值時間以及調整時間也是減小的；液壓缸無桿腔壓力p _ 1 （ t ）的超調量是增加的。 -
Second, engine ' s partial velocity characteristics model and universal characteristics model are built the throttle opening is considered as an essential factor to build the model for reflecting the actual working performance of engine. the situation of the throttle opening change is studied, and a simulation method is given to use torque curved surface and vehicle dynamics equation on base of differential approach method. engine test software is developed for the engine no - load test, variable throttle opening test and throttle step change test
其次，建立了發動機的部分速度特性模型和萬有特性模型；為了更好的反映發動機的實際工作特性，將油門開度作為一個重要參數參與建模，並對發動機變油門的情況進行了研究；結合轉矩曲面和整車動力學方程，採用微區間逼近法確定了發動機變油門過程模擬方法；開發了發動機試驗測控軟體，利用該軟體進行了發動機空載響應試驗、發動機不同油門開度試驗和油門階躍變化試驗，並對實際試驗數據和數學模型計算數據進行對比；在vc + +平臺上開發了發動機特性模擬模塊，在系統中用軟體實現了變油門控制發動機特性的功能。
分享友人