tip angle 中文意思是什麼
tip angle
解釋
頂尖角-
Secondly, programmed the image processing arithmetic code which include the bottom arithmetic for the general condition comprises threshold division, region combination and informate and the middle level arithmetic for the given task comprises detecting the line dation creirection according to the hough transform in order to fix on the hole ’ s azimuth angle, detecting the aiguille tip position according to the image movement according to the environment and the image format
然後，根據目標環境要求和攝像機採集圖像格式，開發了圖像處理演算法程序。圖像處理演算法包括底層演算法和中層演算法兩部分，底層演算法針對通用情況，包括閾值分割、區域合併和信息生成。中層演算法針對具體任務設計，包括利用hough變換檢測棱線的方向，從而確定圓孔的方位角和利用基於圖像運動檢測鉆頭尖端位置。 -
Crack tip opening angle, ctoa
裂尖張角 -
Angle tip relay pliers
繼電器拔取鉗 -
The following conclusions are gained : ( 1 ) the located shear band prongs the ligament near the top crack tip and the structure may occur shear - mode fracture at the angle of 155 ? to crack when load is 87. 92mpa ; the mode of fracture of the flange joint structure is not possible to be void - mode ; ( 2 ) it is proved that loading and then unloading repeatedly can not increase the possibility of invalidation of the structure when the times of loading and unloading are not too more when load is operating pressure ; the structure is safe when the vessel is operating ; ( 3 ) in the fe model of the thesis, not considering the influence of water pressure test which is in the process of fabrication of vessel in fe results in larger deviation in analysi
得出了以下結論：在8792mpa的載荷下筒體一封頭連接結構處的集中剪切帶貫穿韌帶，可能發生沿與原裂紋線成155 「角方向剪切型斷裂；筒體一封頭連接結構不可能發生韌窩型斷裂； （ 2 ）在工作壓力下進行次數不多的反復加、卸載，結構不會破壞，也不會喪失安定性：結構在工作狀態下是安全的； m在本文的彈塑性有限元模擬計算中，對于裂紋尖端進行力學分析時，不考慮壓力容器製造過程中水壓試驗的影響，將導致計算結果出現較大的偏差； （ 4 ）筒體完全屈服時的載荷為92石3mpa ，封頭完全屈服時載荷為86 -
According to elasto - plasticity theory, with the help of finite - method program ansys, the paper undertakes the computer analogue tests about the bearing capacity of pile tip arranged by orthogonal principle, and attains the relations of pile - tip bearing capacity to embedment depth, pile diameter, cohesion, internal friction angle and modulus of deformation. by the means of mathematical statistic, regression equation of the ultimate bearing capacity calculated by finite element method is gained through the regression analysis of 81 group data from the computer analogue tests. by comparison and analysis of the values calculated by finite - element regression equation and the values of in situ loading test, the regression equation is gained which calculates the size effect for base resistance of large diameter pile
根據彈塑性理論，運用大型有限元軟體ansys按正交設計理論對樁端承載力進行模擬計算，獲得樁端承載力與樁長（埋置深度） 、樁徑、粘聚力、內摩擦角及變形模量等主要影響因素的關系，並採用數理統計方法，對81組ansys模擬試驗結果數據進行回歸分析，得到有限元法確定樁端極限承載力的回歸公式，並將有限元法回歸公式計算值與現場小壓板載荷試驗值進行比較分析，得到大直徑樁端阻的尺寸效應系數計算公式。 -
In the control scheme using neural network, the control of flexible manipulator is separated into angle - following control of slow subsystem and vibration - suppressing control of fast subsystem based on singular perturbation and time decomposition. moreover, the paper discusses the structure and the algorithm of neural network plus fuzzy pd control of tip vibration. finally the performance of designed methods is validated by simulation
對于神經網路控制，首先根據奇異攝動和兩時標分解，將柔性連桿機械臂的控制分解成等效剛性臂慢子系統的角跟隨運動控制和快子系統的消振控制，論文給出了神經網路+末端振動模糊pd控制的結構和計演算法，並通過實驗研究驗證了提出設計方法的性能。 -
The changing procedure includes : extending of the blade on the tip, extending of the blade on the root, expanding of the surfaces of the blade, extending of the blade on both sides, calculating the balance angle, changing the coordinate system, changing the data on the consideration of the shrinking and the reflecting of the blade material, etc. a blade surface is bended and distorted in three dimensions
具體轉化過程包括：葉尖型面延伸、葉根型面延伸、葉身型面余量加放、進排氣邊余量加放、平衡角的計算、考慮葉片的收縮和回彈、坐標轉換等。完成了葉身實體造型。葉身型面是復雜三維彎扭曲面，造型上既有精度要求又有光順性要求。
分享友人