tooth number 中文意思是什麼
tooth number
解釋
齒數-
On the profile modification in the cycloidal pump with multi - tooth number difference
多齒差擺線泵的齒形修正 -
The prosthodontics office takes on the prosthodontical tasks for the patients with tooth missing problems. the diagnosis and treatment work require high professional skills, and the information - awaiting disposition - is in various forms and a large number, especially there being much content requiring dynamic monitor forthwith
口腔修復科擔負著牙體、牙列缺損或缺失患者的口腔修復工作，診療工作專業性強，需要處理的信息形式多、數據量大，特別是要求進行實時動態監控的內容多。 -
As both the meshing point and ball ' s center are on the given cylinder, a general method for developing the cam ' s profile is studied. it is proved that the profile of positive and negative transmission is unique if the face gear, the difference between face tooth number and ball number and the diameter of ball are the same. the concrete expression of meshing cam on given spatial cycloid profile, and the characteristics of the profiles are discussed
論文的主要工作包括： 1 、根據嚙合點和鋼球中心軌跡均在同一圓柱面上的特點，研究了給定端齒齒廓條件下求解凸輪齒廓的一般方法；論證了在給定端齒、齒差數和鋼球直徑相同的條件下，正負齒差嚙合齒廓的唯一性；討論了端齒為球面擺線時，凸輪齒廓的具體表達式，並研究了該齒廓的性質。 -
This paper proposes a new method to obtain any wanted stepping angle with adjustable and even subdivision. with the method, the stepping angle is n ' t restricted with different phase number and tooth number any longer. so the product arrangement of stepping motors and drives can be simplified
提出了通過任意均勻細分來實現任意步距角的新方法，從而打破步進電動機相數和齒數對步距角的限制，簡化步進電動機及驅動器的生產格局，充分發揮機電一體化的系統效果。 -
The pump gears with large module and less number of teeth are adopted by the high viscidity gear pump. when they are in mesh, meshing interference happens. in order to avoid interference of flank, tooth profile is modified
高粘度齒輪泵中的泵齒輪通常模數大，齒數少，它們嚙合時常發生干涉，為了消除嚙合干涉，需對泵齒輪進行修形。 -
For cutting the composite lock gear with unequal tooth thickness, a study is made on the design method of gear sharper cutter with nonstandard parameter involute tooth profile and noninvolute tooth profile. the cutter tooth arrangement, the choice of teeth number of the cutter and the basic method of cutter design are discussed ; and a new method of choosing deflection factor by using limited area is presented. and the curve of relationship between rear angle on tooth crest and helical angle on tooth side of the cutter is given so as to give a basis for the gear sharper cutter to choose its parameters. to design nonstandard gear sharper cutter by adopting the method mentioned above will simplify the calculation and will increase the efficiency of design
研究加工不等齒厚的非標準參數漸開線齒形，與非漸開線齒形復合的鎖閉齒輪插齒刀刀齒的排列、刀具齒數的選擇以及刀具設計的基本方法，介紹用限制區域選擇插齒刀變位系數的新方法，並給出刀具齒頂后角與側螺旋角的關系曲線，為插齒刀參數的選擇提供依據.結果表明，採用上述方法設計非標準復合齒輪插齒刀，可簡化計算和提高設計效率 -
Secondly, based on the research of flow characteristic of hydraulic motor with multi cylindrical gear, optimal conditions of tooth number are got to minimal the pulsation ratio of motor in the design of hydraulic motor
其次，通過對圓柱多齒輪式液壓馬達的流量特性進行研究分析，得出使其排量脈動率最小所必須的各齒輪齒數應滿足的設計準則。 -
Translation modes are similarly independent of the rotational support stiffnesses. large contact ratio do not mean lower mesh force. if either the number of sun or ring gear is not multiple of planet gear, system will run effectively, with lower impaction of tooth mesh in and out
研究表明：扭轉支撐剛度的變化影響系統的轉動模態，徑向支撐剛度（行星架的除外）的變化影響系統的位移模態；齒輪間重合度大並不等於輪齒間的受力情況好；行星輪與內齒圈齒數不為行星輪個數的整數被時，輪齒的嚙入、嚙出對系統的沖擊小，系統的效率高。 -
3. base on the numeric method of finite element, the influence of interrelated shift coefficient and tooth number z to bend intensity of gear is studied. with the increase of the tooth number, tooth root maximum pull stress decrease ; with the increase of the interrelated shift coefficient, tooth root maximum pull stress increase
3 、基於有限元數值計算方法，分析了不同關聯變位系數和齒數z對齒輪彎曲強度的影響：隨著齒數的增大，齒輪最大拉應力減小；關聯變位系數越大，齒輪最大拉應力越大。 -
Abstract : the measurement of asymmetric gear is discussed, especially the measurement of base tan - gent length of this kind of gear is studied in details. the formula of measuring and calculating the base tangent length and the number of tooth - jump are deduced in order to use in real production
文摘:就非對稱齒輪的測量問題進行探討，特別是公法線長度測量進行詳細研究，並推導出計算公式和跨齒數，以便於以後在生產上使用 -
When bears enough loading, actual contact tooth number will exceed theoretic contact tooth number, which makes the loading capacity of the gears increased dramatically
三環傳動在足夠大的載荷作用下，實際嚙合齒數會大於理論嚙合齒數，使得三環減速器中齒輪副的承載能力大大提高。 -
Aimed to the two deficiencies of three - ring gear transmission, the dissertation will analyze these two aspects. the first, according to the finite element model of gear pair of three - ring gear reducer, the dissertation is aimed to analyze the multi - tooth meshing effect of three - ring gear reducer using finite element method, and the number of teeth contacted simultaneously, their load distribution characteristics and the von mises stress change are gained
針對三環減速器以上兩點的不足之處，本文將對以下兩方面進行分析:首先，本文以三環減速器齒輪副有限元模型為研究對象，利用有限單元法對三環減速器多齒嚙合效應進行分析，得到三環減速器傳動時的實際接觸齒數、嚙合齒載荷分配以及vonmises應力變化規律。
分享友人