tooth pressure 中文意思是什麼
tooth pressure
解釋
齒廓-
On the base of the basic structure study of the tooth - locked quick closure vessel of middle and low pressure with crown head, the optimization method of parameterized whole device is presented in this paper, the emphases of research is put on optimization of the tooth - locked quick closure device whose structure and load distribution is complicated, the wall of vessel, however, is designed according to the existing strength formula
本文對帶有球冠形封頭的中、低壓齒嚙式快開容器的基本結構進行研究的基礎上，提出了齒嚙式快開容器的參數化整體優化方法，研究重點放在結構和受力復雜的齒嚙式快開裝置的優化，對于容器簡體壁厚仍採用現有強度公式設計。 -
The influence law of gear ' s bending stress affected by nominal pressure angle and technological angle of tooth profile has been summarized and obtained a conclusion that the maximum bending stress before running in period occurred at the waist place of the tooth, thus provided a theoretical foundation for the design and application of double arced gears
總結了名義壓力角和齒形工藝角對輪齒彎曲應力的影響規律，並得出跑合前最大彎曲應力發生在齒腰處的結論，為雙圓弧齒輪的設計和使用提供理論依據。 -
The equation of pressure angle, width coefficient, and contact ratio are calculated and the influences of these parameters on contact are analyzed. based on ordinary involute gear, the diametral deflection principle of curvilinear - tooth
最後針對現有文獻的不足，研究了刀具壓力角、齒寬系數和重合度等參數的計算方法，並分析了這些參數對弧齒線圓柱齒輪嚙合的影響。 -
Firstly, based on research of the asymmetric involute gear cutter and the gearing theories, the universal tooth flank curve equations of asymmetric gear with two pressure angles and the tooth transmission curve are derived by the gear shape nomal method, then the fea model of asymmetric involute gear with main parameters is automatically generated with ansys parametric design language ( apdl )
本文首先建立非對稱漸開線刀具的方程，根據齒形法線法建立非對稱漸開線齒輪的齒廓曲線方程，並利用apdl參數化建模語言建立全參數的非對稱漸開線齒輪有限元模型。討論了非對稱漸開線齒輪的嚙合特性，對非對稱漸開線齒輪傳動特點作了詳細的分析。 -
Inverted tooth silent chains with 30 pressure angle
30壓力角的逆齒無聲鏈 -
Symptoms of calcium deficiency include muscle cramps, tremors, or spasms, insomnia, nervousness, joint pain, osteoarthritis, tooth decay and high blood pressure. severe deficiency results in osteoporosis or porous bones
人體從35歲左右開始，每天就會丟失30 - 50毫克的鈣質，到了50歲，骨頭的總重量減輕至0 . 7公斤左右。 -
Taking gear without tooth face invalidation such as agglutination and abrasion as a precondition, and according to the relation between minimal oil film thickness and tooth face roughness of elastic liquid dynamic pressure lubrication theory, viscosity of gear lubrication oil was educed by reliability method in this paper, and the calculation formula has been elicited and applied
摘要以齒輪傳動不發生膠合、磨損等齒面失效為前提，根據彈性流體動壓潤滑理論的最小油膜厚度與齒面粗糙度的關系，用可靠性方法確定齒輪潤滑油的粘度，給出計算公式並進行了實例計算。 -
This paper deduced the involute gear total tooth profile equations of unsymmetric teeth with double pressure angles, proposed the calculation formulas of coordinates and load angle at the upper and lower points of single and double teeth mesh areas, and programmed the relevant parametric programs
摘要推導出雙壓力角非對稱漸開線齒輪系統全齒廓方程，以及在單、雙齒嚙合上、下界點處坐標和載荷角的計算公式，編制了相應的參數化程序。 -
By considering the contact between the teeth and utilizing the face to face contact model with contact element and coulomb friction model, the author have developed a computing method for plastic load of tooth - locked quick actuating pressure vessel based on finite element stress analysis and stress categorization
摘要通過接觸單元來數值模擬嚙合齒的接觸過程，建立了基於整體有限元分析的齒嚙式快開壓力容器塑性載荷計算方法。 -
In the process of use and repair, before the confirmation of reliable connection of valve stem and handle, tooth disk or drive head and other parts, the valve can not access to medium to bear pressure, otherwise the valve stem may dash out, causes dangerous accidents
使用或維修過程中，在閥桿與手柄、齒盤或傳動頭等部件確認可靠連接前，閥門不能通入介質承壓，否則可能使閥桿沖出，造成危險事故。
分享友人