torque-angle 中文意思是什麼

torque-angle 解釋
轉矩角
  • torque : n. 1. (古代條頓人、高盧人戴的)金絲項圈。2. 【物理學】扭(力)矩,轉(力)矩。
  • angle : n 【英史】盎格魯人〈cf Angles〉。n 1 角,隅,角落;棱,嬗角。2 【數學】角,角位,角的度數。3 【機...
  1. At first, according to the concrete requirement of the servo control system, a collective scheme, which provide guarantee to meet the requirements of the global performance, is established. in this scheme, the structure of gimbal and the torque motor driven mode are adopted, and angle measurement is accomplished by inductosyn and velocity measurement is accomplished by dynamically tuned gyro respectively

    首先,根據目標真值測量設備伺服系統的具體要求,確定了地平式常平架結構,力矩電機驅動,分別採用動力調諧式速率陀螺儀及圓盤式感應同步器作為速率及位置反饋元件這一總體方案,為伺服系統滿足整體性能指標要求提供了保證。
  2. Secondly, the effects of the crest width of the back - emf waveform to the torque ripple in the 120 ? conduction mode are analyzed, among which the effects of the advance commutation angle to the torque ripple are quantificationally analyzed for the bldcm drives whose back - emf waveform crest width is less than 120 ?,

    其次分析了120導通方式下反電動勢平頂寬度對轉矩脈動的影響,對于平頂寬度小於120電角的非理想梯形波反電動勢,定量分析了換相超前角對換相轉矩脈動的影響。
  3. For the bldcm which has a pseudo - sinusoidal back - emf waveform, this dissertation presents a svpwm control method using six discrete position signals for minimizing the torque ripple. the main aspects for the implementation of this method are analyzed, including the initial orientation of the voltage vector, reasonable choice of the impedance angle and the advance commutation angle, and estimation of the successive rotor positions

    針對反電動勢類似正弦的準正弦波反電動勢無刷直流電動機,本文提出一種基於六個離散位置信號的自同步svpwm (電壓空間矢量法)控制方法,用以削弱電磁轉矩脈動,分析了實現這種方法的主要控制環節,包括起動時電壓空間矢量的初始定位,阻抗角與電流超前角的合理選擇以及連續轉子位置的估計等。
  4. Most of the fin stabilizers we use now are angle - feedback system, whose control torque is gotten by the calculation of fin angle

    目前使用的絕大多數減搖鰭都是角度反饋系統,它通過鰭的轉角來計算控制力矩。
  5. Fin stabilizer is a kind of active stabilizer, which is designed on the principle of torque counteraction. fin stabilizer applied at present is an angle feedback system which calculate the controlling torque through the fin angle. because the relationship between the lift produced by fin and the fin angle is mainly determined by the hydrodynamic experiment, so there are some defects

    目前使用的減搖鰭是一個角度反饋系統,它通過鰭的轉角來計算控制力矩,這樣就存在一些不足之處,因為鰭上產生的升力和鰭角的對應關系主要靠鰭模的水動力試驗來求得。
  6. Because the relationship between the lift on the fin and the fin angle is gotten by the static hydrodynamic experiment, which has great error, especially dynamic hydrodynamic experiment, the control torque gotten by the experiment can not counteract the wave torque well and the stabilization result is not perfect

    而鰭的水動力試驗存在著很大的誤差,特別是在動態條件下,鰭的水動力特性測試更困難,所以這種通過計算求得控制力矩的方法產生的鰭升力無法很好地抵消波浪力矩,因而影響了減搖效果。
  7. This dissertation mainly investigates some robust control strategies of the electromechanical actuator which is supposed to be activated by the sinusoidal permanent magnet synchronous motor ( pmsm ) and limited angle torque motor ( latm )

    本文主要研究了基於正弦波永磁同步電機( pmsm )及有限轉角力矩電機( latm )驅動的電動舵機的魯棒控制策略。
  8. After the construct of the motion simulation model, genetic algorithm is used to do the adjustment of pid parameters of the control system of the joint motors, integral separation pid control and angle error analysis is finished, and three force / torque sensors, touch sensors, distance sensors and photoelectric switches are calibrated and installed

    在建立了機器人關節控制系統模型后,使用遺傳演算法對其關節電機控制系統進行pid參數整定,進行機器人關節的積分分離的pid控制策略和轉角誤差的理論分析,並進行了機器人三維力/力矩傳感器、接觸傳感器、測距傳感器和光電開關的標定與安裝。
  9. 5. no parts and components warranty will be delivered if customer or non - warranty - taker dismantles disassemble and adjusts parts, assembly of the diesel and components that are not allowed to be adjusted such as injection pump assembly lead sealing, and reassembles them within the warranty term, which however, fails to meet technology demand such as torque and advance angle of major bolts, resulting in failure and damage of relevant components, assembly and parts

    在保修期內,顧客或非承擔保修者拆卸解體調整柴油機的部件總成和規定不得調整的部位如噴油泵總成鉛封等,重裝后又未達到技術要求如重要螺釘的扭矩噴油提前角等,導致部件總成和相關聯零部件失效和損壞,由此涉及的零部件
  10. Chapter three makes clear the importance of preload, and deals with the theories on the relationship between preload and torque, angle and extension of the bolt from various aspects

    第三章由扭矩控制的實質? ?預緊力,點明了預緊力的重要性,預緊力與擰緊力矩、螺母轉角、螺栓伸長的關系,對其進行了理論方面的研究和探討。
  11. Several strategies are shown in this thesis to minimize the torque ripple and achieve the performance. these strategies include dtc control of srm and a fuzzy - logic - based torque ripple reduction method for switched reluctance motors using a turn - off angle compensator approach. simulations show that these strategies can reduce the torque ripple

    本文介紹了能夠消除srm的轉矩脈動,提高srd性能的幾種新型控制策略,即srm的直接轉矩控制、基於模糊邏輯的關斷角_ ( off )的優化控制,並進行了模擬。
  12. Based on the model of a three - phase hybrid stepping motor, the torque expression is deduced. the effect of subdivided driving on operating performance is analysed. it is illustrated that sine wave subdivided driving can make stepping angle and torque equal

    本文以三相混合式步進電動機數學模型為基礎,推導出其轉矩解析式,分析了細分驅動對于改善步進電動機運行性能的作用,論述了正弦波細分驅動可以實現等步距角、等力矩均勻細分驅動的原理。
  13. The results of iem and fem show the effectiveness and advantages of iem for pmss. on the basis of field analysis of pmss, the paper describes the calculation of torque of pmss using maxwell stress method ( msm ). the torque - angle characteristic of pmss is also analyzed by msm

    在對永磁步進球形電動機磁場分析的基礎上,本文採用麥克斯韋張量法,建立了永磁步進球形電動機轉矩的計算方法,在matlab環境下編寫程序對電機實例的矩角特性進行了分析。
  14. A variable - speed dtc pmsm system is set up to verify the dtc theory in pmsm, that is to control the toque by controlling the torque angle of motor if the stator flux linkage keeps constant. this paper points out the function of the space voltage vector by which the torque angle can be changed according to the need of torque of the motor

    主要作了以下開創性的工作:系統地闡述了永磁同步電機直接轉矩控制理論,發展了原有的控制理論,明確了空間電壓零矢量在控制系統中的重要作用? ?保持電機轉矩輸出,減小轉矩脈動,據此提出了包括零矢量的新型控制方法。
  15. Firstly, this paper proposes the mathematical model and finite - element analysis model of torque motor with mf and without mf. secondly, the electromagnetic field of torque motor is analyzed using the ansoft maxwell software ; static output torque of torque motor with mf and without mf is calculated. then the rotary angle of torque motor with different input electric current and mf is measured using three - coordinate measurement device

    本文首先給出了添加磁流體和不添加磁流體的力矩馬達磁路數學模型及有限元分析模型,其次,利用ansoft公司的maxwell電磁場分析軟體進行了力矩馬達的二維和三維磁場有限元分析,對添加磁流體和不添加磁流體的力矩馬達靜態輸出力矩進行了計算,並採用三坐標位移測量儀對不同輸入電流作用下、添加不同特性磁流體時力矩馬達的轉角進行了測量,從而對輸出力矩特性進行了實驗研究。
  16. The method of torque - angle is adopted as the control method of the intelligent screw tightening machine on the basis of analyzing the excellence and deficiency of all kinds of control methods and taking practical situation into account. secondly, the design of the machinery of the tightening machine is explained in detail, almost all parts of the structure principle diagrams are given and an introduction of function of each part in the diagram is made concisely

    文章首先對螺紋擰緊的控制方法進行了探討,在分析各種方法優缺點和結合實際情況的基礎上採用扭矩轉角法為螺紋自動擰緊機的控制方法。然後,文章詳細地介紹了擰緊機的機構部分設計,給出了擰緊機的各部分的結構原理圖,並對原理圖中的各個環節的功能作了簡要介紹。
  17. Torque angle gauge

    盤頭螺絲扭力角度規
  18. Fasteners - tightening performance - torque angle simplified test method

    緊固件.緊固性能.扭矩角度簡易試驗方法
  19. Fasteners - tightening performance - torque angle simplified test method ; german version en 14831 : 2005

    緊固件.上緊性能.扭矩角度簡化試驗法
  20. Direct torque control using space vector modulation ( svm - dtc ) scheme is discussed and the detailed designed, including space vector choosing and modulating, to overcome the control difficulties coming with the characteristic of low inductance. comparing with the basic dtc, the simulation results confirm the feasibility and good performance of this strategy. in order to reduce the torque error in dynamic state resulted from the nonlinear relationship between the torque and torque angle, a proportional - plus - integral ( pi ) torque controller with variable proportion is presented to ensure exact and quick control of torque in dynamic state

    系統的闡述了永磁同步電機直接轉矩控制理論,分析了改進后的svm - dtc控制策略,並具體設計了控制技術的實現方案,包括參考矢量的生成和空間電壓矢量調制的方法;為減小電磁轉矩與轉矩角非線性關系這一因數給電機電磁轉矩動態調節造成的誤差,本文實現了變比例系數轉矩pi調節器的方案,確保了系統穩定性的同時,實現了電磁轉矩在動態過程中快速而準確調節。
分享友人