torsion failure 中文意思是什麼
torsion failure
解釋
扭轉斷裂-
Research has been done on the calculating methods of lateral stiffness and bearing capacity of the frame. according to experimental studies, finite element analysis and theoretical analysis, it develops to calculate lateral stiffness of frame with special - shaped columns of greater height - width ratio by using frame with rigid zones, and considering shear deformation of beam and columns. without considering the torsion of the whole structure, assuming the special - shaped column in the rc frame is flexural failure under uniaxial eccentricity force, putting forward the calculation method of flexural strength of special - shaped columns and the shear strength in a story for r. c
對異形柱框架分別按普通框架和壁式框架進行分析，並與空間有限元分析結果和試驗結果進行比較，提出了異形柱框架結構側向剛度的計算方法；在整體結構不產生扭轉且異形柱為彎曲破壞的假定下，提出了異形柱的受彎承載力及受剪承載力計算公式；提出了根據異形柱框架結構的破壞機構確定其樓層受剪承載力的方法。 -
Analysis of torsion failure of motor shaft
電機主軸扭斷原因分析 -
Also the failure modes and the cracking torque, original stiffness, ultimate torsion strength and ductility are discussed in this case. the factors affected torsion bearing capacity of high - strength concrete frame column is analyzed too. the seismic performances of normal - strength and high - strength concrete frame column subjected to biaxial eccentric compression, shear and reversed torque are studied
以軸壓比和相對偏心距為主要研究參數，揭示高強鋼筋混凝土構件在單向、雙向偏壓剪單調、反復扭矩作用下的破壞特徵、開裂扭矩、剛度、強度、延性等特性，分析了影響高強混凝土框架柱抗扭承載力的因素。 -
And the theoretical a nalyses done in this paper are listed below : first, the experimental data on the members of varied parameters under torsion demonstrate the general rule of the deformation while the tubular is under torsion. the paper establishes three phases of the deformation of the tubular under torsion, namely, the elastic deformation, the elastic - plastic deformation, and ultimate failure. through regression analysis, a simplified method is proposed for calculating the capabilities of the tubular under elastoplastic torsion, and the formulary for bearing value, is also recommended as a reference in engineering design
本文根據不同參數的構件受扭性能試驗結果，研究了該結構受力變形全過程的基本規律，提出了受鈕全過程的三個工作價段，即彈性變形階段，彈塑性變形階段和極限破壞階段，經分析回歸得到扭轉全過程彈塑性的簡化分析方法及承載力計算公式，可供工程設計參考；同時根據本文的彎扭試驗結果以及對離心鋼管混凝土構件進行的理論分析，推導了彎扭試驗相關承載力的關系。 -
By tests of 9 specimens subjected to biaxial eccentric compression, shear and reversed torque, the failure modes and the varying laws of cracking torque, original stiffness, ultimate torsion strength and ductility are discussed, with the change of axial stress level and relative eccentricity. then, the cracking bearing capacity, the ultimate capacity and the deformability of the specimens are obtained
通過9根承受雙向偏壓、彎、剪構件在反復扭矩作用下的試驗研究，以軸壓比和相對偏心距為主要研究參數，揭示鋼筋混凝土構件中雙向偏壓剪反復扭矩作用下的破壞特徵、開裂扭矩、剛度、強度、延性等特性和耗能性能，從而確定其開裂承載能力和極限承載能力及變形性能。
分享友人