transfer number 中文意思是什麼

transfer number 解釋
遷移數
  • transfer : n 1 移轉，轉送；調職；調任[轉學]證書；變換。2 （財產；權利等的）轉讓，讓與（證書），移轉，授受；...
  • number : n 1 數；數字；〈pl 〉算術。2 （汽車等的）號碼；第…，第…卷，第…期〈通常略作 No （復數 Nos ），用於...
  1. In this paper, using phoenics software to compute and analyze the variety rule of the convecting transfer heat at the basis of computing and analyzing the temperature and velocity field of one underfloor supply air room with a focus hot source, and concluding that the number of the hot source and the supply air outlet > the intensity of the hot source and the volume of supply air will influence convecting transfer heat, and obtained its correlativity formula

    本文針對一下部有集中熱源的地板送風空調小室，利用phoenics軟體，在計算分析小室內氣流的速度場及溫度場的基礎上，對對流熱轉移量的變化規律做了計算分析，最後得出對于下送風小室的對流熱轉移量與熱源的個數、送風口個數、熱源強度、送風量等因素有關，並且得出了其相關關系式。
  2. At the same time, i discover that the number of the return air inlet has a little influecing and it can be neglected. when there is hot resource at upperside of the room, the hot jet and supply air jet together affecting. at the same lower part heat intensity, a utmost wind speed exist, the supply air speed lower, the more heat intensity on the upside, the less convecting transfer heat, whereas

    對于上部有熱源的條件下，則其對流熱轉移量的變化關系是由熱射流與送風冷射流共同作用影響的，在下部熱源強度相同的條件下，存在一極限風速，在該風速以下，上部熱源強度越大，則對流熱轉移量越小，反之在該風速以上，上部熱源強度越大，則對流熱移量越大。
  3. In order to verify these numerical results, we analytically obtained the end positions of the phase - locked steps those have the transfer number 1 / n and found a good agreement with the numerical results

    為了驗證這一數值結果的正確性，我們解析求解了穿越數為1 / n的鎖相臺階的參數位置，發現和數值結果符合得很好。
  4. The characteristic quantity ( like the " transfer number " defined in this thesis ) that describes the higher period orbits forms a sequence of phase - locked steps on the plane formed by it and the control parameter. all the phase - locked steps form a so - called prelude phase - locking staircase to type v intermittency

    描述這些過渡高周期軌道的特徵量（如本文定義的穿越數）在這個特徵量和控制參量構成的平面上形成一系列鎖相臺階，所有的臺階構成所謂的v型陣發前奏階梯。
  5. Therefore, because the number of samples is less, but in order to successfully get orders, the printing surface treatment ( signs nameplate, etc. ) can not be lax, the usual choice of either silk screen, and pad printing or thermal transfer, but for a small number of sample products or the case is a long life cycle, cost, efficiency in my company ' s products, printing effects, the cost has obvious advantages

    因為是樣品所以數量少，但為了順利拿到定單，表面的印刷處理（標志、銘牌等）又不能馬虎，通常的選擇不外乎絲印、移印或熱轉印，但針對樣品或少量產品而言則周期長、成本高，我公司產品在效率、印刷效果、成本方面具有明顯優勢。
  6. The results indicate that : the high positioned air inflow do good to heat transfer in rotator disk ; different size of radial outflow have small effects on flow and heat transfer ; the heat transfer near rotating disk increases as rotating reynold number increases or non - dimensional mass flow rate increases

    結果表明，高位軸向進氣對轉盤換熱有利；不同的徑向出口大小對盤腔內的流動換熱影響不大；隨旋轉雷諾數和無量綱質量流量增加，轉盤盤面的換熱效果增強。
  7. By comparing the results with relative experiment data, it is shown that rng k - is more exactly than the other turbulent model. 2 ) the influences of axial inflow position, radial outflow size, rotating reynold number, non - dimensional mass flowrate and axial inflow angle on the flow and heat transfer characteristics were numerically investigated for a typical rotator - stator cavity with axial inflow, radial inflow and radial outflow. the correlations for average nusselt number vs rotating reynold number or non - dimensional mass flowrate were established

    （ 2 ）針對一典型的徑向、軸向進氣，徑向出氣的轉-靜盤腔結構，系統研究軸向進氣位置、徑向出口大小、旋轉雷諾數、無量綱質量流量和軸向垂直預旋進氣等對盤腔內流動和換熱的影響，整理出轉-靜盤腔內轉盤平均努謝爾數與旋轉雷諾數無量綱質量流量之間的準則關聯式。
  8. 4 ) in a pre - swirl rotator - stator cavities with discrete pre - swirl nozzles and blade - cooling entry holes, the influences of pre - swirl angle and flow parameter on the flow and heat transfer characteristics were numerically investigated. the correlation for average nusselt number vs rotating reynold number or non - dimensional mass flowrate were established. the results show that : advantage of per - swirl inflow is the effect of cooling the blade - cooling entry holes ; pre - swirl inflow increases heat transfer in rotating disk of pre - swirl chamber ; as pre - swirl angle increases, local nusselt number decreases in pre - swirl chamber ; the temperature of stator of inner rotator - stator chamber and per - swirl chamber decreases as rotating reynold number increases ; when the axial mass flowrate maintains constant, heat transfer in the rotating disk of inner rotator - stator cavities does n ' t change as per - swirl mass flowrate increases, while heat transfer in the rotating disk of per - swirl chamber increases ; when the pre - swirl mass flowrate maintains constant, change of the axial mass flowrate has effect on the whole cavity

    結果表明，預旋進氣的優點在於增強了葉片冷卻孔附近的對流換熱效果，局部努謝爾數隨預旋角的增大而有所減小；隨旋轉雷諾數的增加，不論是內轉靜腔室還是預旋腔室的靜盤上的溫度都不同程度的降低：當軸向中心進氣質量流量不變時，隨預旋進氣的質量流量增加，內轉靜腔室的轉盤盤面上的換熱基本沒有變化，而預旋腔室的轉盤盤面上的換熱效果增強；當預旋進氣質量流量不變時，軸向中心進氣的質量流量的改變對整個盤腔都有影響。
  9. Fixed number of year for transfer and sublease : 28 years from 2005 to april 2, 2033 ( the exact time depends on the contract

    二、租轉讓年限： 2005年至2033年4月2日計28年（準確時間以簽訂合同為準） 。
  10. The number of companies that receive special treatment or particular transfer because of the wildness of internal control system has been increasing recently. the historian arnold j. toynbee said, as for a country, even for a nation, its wane starts from the interior. the exterior force is only the ultimate strike before it deceases

    近年來，因內控失控而導致st 、 pt公司的不斷增加已成為我國上市公司中的一道風景，歷史學家湯因比說過： 「一個國家乃至一個民族，其衰亡是從內部開始的，外部力量不過是其衰亡前的最後一擊。 」
  11. Already, there have been a number of successful technology transfer cases at cuhk.

    中文大學在移動技術方面，已經有多個成功的技術轉移或與業界合作的例子。
  12. It is suggested that in the regions of aqueous soil with faster seepage velocity, either the tube - wells can be spaced adequately closer or for the same spacing the number of tube - wells and length of tubes can be reduced under the condition of assuring regular heat transfer effect

    在滲流速度較大的富水地區，在保證常規換熱效果的情況下，管井間距可適當減小，或在同樣管井間距下，可減少管井數量或減小理管長度。
  13. Results show that the influence of mainstream reynolds numbers on heat transfer coefficience is little and the heat transfer coefficience raise with the increase of reynolds numbers. the influence of the position of holes on heat transfer coefficience is complex and correlate with the mainstream speed and the balde surface curvature. and the influence of blowing ratio on heat transfer coefficience is more great ( especially to stator ), and show a complex relation to mainstream reynolds number and the position of holes

    實驗結果表明，不同孔位出流的換熱由於孔排下游表面來流速度及葉片表面曲率的不同而有不同的規律，而主流雷諾數對葉片表面特別是壓力面和前緣區域的換熱系數比的影響較小，吹風比對換熱系數影響較大（特別是導葉） ，並且隨氣膜孔位置和來流雷諾數的變化而情況復雜。
  14. The thermal visualizations of jet impingement cooling with single or double row holes inside semi - enclosed channel are measured by using infrared camera and then the impingement cooling heat transfer coefficients are deduced. the effects of flow and geometry parameters on convective heat coefficients are obtained. the results show that : for a single row normal impingement, the impingement cooling effectiveness is enhanced with the increase of impinging reynolds number or the decrease of hole space to diameter ratio, and the best effectiveness is achieved under the jet - to - surface spacing equals to 2 ; when the jet is oblique to the confined wall, the cooling effectiveness is weaken especially under the jet - to - surface spacing ratio is greater than 2 ; for double rows normal impingement cooling, the cooling effectiveness of rear row jet is weaker than the front row under lower impinging reynolds number or bigger jet - to - surface spacing

    對于單排垂直射流，沖擊冷卻效果隨射流雷諾數的增加、孔間距與直徑比的減小而得到提高，沖擊間距比為2時換熱效果最好;沖擊孔中心線向通道封閉一側傾斜后，射流沖擊冷卻的范圍變窄，當沖擊間距比大於2時駐點區的對流換熱能力明顯降低;對于雙排沖擊射流，孔排間距與直徑比的增加使沖擊冷卻范圍變大，但在兩排孔之間區域的對流換熱系數有所下降;在較小的沖擊射流雷諾數和較大的沖擊間距比下，後排射流的沖擊換熱效果要遜於前排射流。
  15. Company now have independence develop ten many china patent and many independence intellectual property ' s software copyright ' s product ; company major product : cable television consumer management control system ( but look for address 2 - 8 branches allot style, 8 - 32 gather line style ) ; shoot frequently plus unfasten harass system ( crowd plus crowd unfasten, cent two sections, point channel shan unfasten ) ; video frequency number subsections plus unfasten harass system ; cable television network burglarproof sow system ; number cable television product is with number mmds ( microwave ) systematically ; general purpose type prevent thunder supply electric appliances, shoot frequently automate supply electric appliances, but look for address control supply electric appliances ; power supply prevents thunder protection product ; pass flow branch, dispenser, split utensil, cavernous wave utensil, power supply inserts utensil, but transfer attenuator, but transfer equalizer wait for

    目前擁有十多項中國專利和多個自主知識產權的軟體版權的產品；公司主要產品：有線電視用戶管理控制系統（可尋址2 - 8戶分支分配式、 8 - 32戶集線式） ；射頻加解擾系統（群加群解、分兩段、按頻道單解） ；視頻數字分段加解擾系統；有線電視網路防盜播系統；數字有線電視產品與數字mmds （微波）系統；通用型防雷供電器，射頻自動控制供電器，可尋址控制供電器；電源防雷保護產品；過流分支、分配器，分流器、陷波器、電源插入器，衰減器、均衡器等。
  16. Bank teller operator : it can check in and check out the teller and indicate the queue ; it can call and recall the number, prioritize a number, give up a number, transfer service and suspend window scrvice

    櫃員操作器：可實現員工登錄退出有人排隊提示可按鍵實現排隊號碼呼叫重呼優先呼叫棄號業務轉移暫停窗口服務等功能。
  17. In this paper, the sensibility analysis of the factors affecting the temperature in well bore is relatively systematically made by using a large number of the data calculated with the borehole flow and heat transfer 3 ? d numerical model proposed by the author. the study shows that the thermophysical parameters of the drilling fluid and formation, etc. and the entrance temperature and circulating capacity, etc. of drilling fluid have a greater influence on the temperature in well bore. therefore, accurately mastering the thermophysical parameter values of penetrated formation and drilling fluid in well bore, considering the influence of the temperature and pressure on thermophysical parameters and accurately measuring such parameters as entrance temperature and discharge capacity of drilling fluid, etc. are of utmost importance for accurately simulating the temperature in well bore

    利用由作者提出的井內流動和傳熱的三維數值模型計算所得的大量數據，文章對影響井內溫度的諸多因素進行了較系統的敏感性分析，研究表明：鉆井液和地層等的熱物理參數以及鉆井液的入口溫度、循環排量等對井內溫度有較大影響，因此，準確掌握所鉆地區地層和井內鉆井液的熱物理參數值，考慮溫度壓力對熱物理參數的影響，準確測量鉆井液的入口溫度、排量等參數值，對于井內溫度的準確模擬至關重要。
  18. The patent application acceptance and awarding of university was studied in this paper, including patent, utility model and industrial design between 1986 and 2001, and the comparative studies with other trades have been carried out ; investigations were done on the relationship between university patent applications, the number of researchers and inventors, application of r & d advances, number of technical service personnel, investment of scientific research funds, patent transfer, number of research and development projects, and number of scientific and technological achievement awards in universities ; 547 staff members of the central south university completed the questionnaire ( 32 questions ) regarding the intellectual property right, knowledge of patents, awareness of patent protection and patent - related behaviors, those people were distributed in the departments of teaching, research, administration and management, and teaching support ; one - way anova, multivariate analysis of variance manova and linear correlation methods were used in the analysis of research - related factors concerning central south university staff members and their understanding of intellectual property right, knowledge of patent, awareness of patent protection and patent - related behaviors, the major factors affecting university patent application, awarding and transfer were identified ; countermeasures to promote university patent development in china were also proposed

    本研究旨在通過對1986年? 2001年我國高校發明專利、實用新型、外觀設計的申請受理與授權情況的分析，並且與其他行業的比較；通過研究我國高校專利申請與高校研發人員數、 r & d成果應用及科技服務人員數、科研經費投入、高校專利轉讓、研究與發展課題數、科技成果獲獎數的關系；通過對中南大學547名教學、科研、黨政管理、教輔人員的產權知識、專利知識、專利意識、專利行為的問卷調查（共32題） ，並用單因素分析法、多元逐步回歸分析法和線性相關分析法，對中南大學在職人員各研究因素與產權知識、專利知識、專利意識、專利行為的統計分析，尋找出制約我國高校專利申請、授權、成果轉讓的因素，提出加速發展我國高校專利工作步伐的對策。
  19. Unless otherwise stipulated in the cerdit ， all documents except invoices and drafts （ if any ） must not show contract number （ if any ） ， nuit price ， invoice number ， invoice date ， value of goods ， insurance percentage and transfer number

    除信用證有規定，所有單據除了匯票和發票外，不要顯示合同號單價發票號，發票日期，貨物價值，保險金額，和轉讓信用證的號碼。
  20. Abstract : a numerical model and experiments over pmma are used to evaluate the main assumptions used in the theoretical description of a diffusion flame established in a natural boundary layer. flow characteristics ( 2 - d boundary layer ) and surface thermal balance are identified as the critical assumptions to be evaluated. comparison of experiments, numerical results, and theoretical model serve to validate the assumptions leading to the definition of a mass transfer number but establish the need to model all three - dimensional features of the flow

    文摘:對pmma進行數字模擬和試驗，對描述自然邊界層擴散火焰理論的假設進行評價.我們把流動特性（二維邊界層）和表面熱平衡作為評價的關鍵假設.試驗、數字模擬和理論模型證實了對質量傳遞數值定義的假設是正確的，但研究也表明，有必要對流動特性進行三維模擬
分享友人
分享到 Line

分享到臉書