trapezoid with 中文意思是什麼

trapezoid with 解釋
曲邊梯形
  • trapezoid : n. ,adj. 1. 〈英國〉不規則四邊形（的）。2. 〈美國〉梯形（的）；【解剖學】小多角骨。adj. -al （trapezoidal thread 【機械工程】梯形螺紋）。
  • with :
  1. A trapezoid is a quadrilateral with two parallel sides.

    梯形是具有兩平行邊的四邊形。
  2. Hard alloy die is made y taking high - quality hard alloy as its nips and fastening with steel die case. it is characterized by high hardness, good thermal conductivity, brasive coefficient and strong resistant to corrosion. it is suitable for drawn metal wire, bar and pipes. the types of dies includes rectangle, hecagon, octagon, diamond, trapezoid, basin and knob, u - shaped and half round types

    硬質合金模具採用優質合金作模芯，並用鋼質模套緊固，具有硬度高，導熱性能好，磨擦系數小，抗腐蝕性等特點，適用於拉制金屬線材，棒材，管材等，另外，模具的類型有矩型、六角型、八角型、菱型、梯型、凹型凸型、馬蹄型、半圓型等各種異形模。
  3. In order to solve this problem, the distribution of the force was studied. with analyzing the data of ship launching, the paper educes seven typical distribution forms, include uniform distribution, sine distribution ( 1 / 2 amplitude ), trapezoid distribution, right triangle distribution, sine distribution ( 1 / 4 amplitude ), parabola distribution, isosceles triangle distribution

    主要有七種分佈形式，包括分佈趨勢較平緩的均勻分佈形式、正弦（ 1 2波形）分佈形式、梯形分佈形式；峰值出現在滑道最前端的直角三角形分佈、正弦（ 1 4波形）分佈、拋物線形分佈；還有峰值出現在分佈區域中間的等腰三角形分佈。
  4. Iiaccording to customers requirement, we can process common or special melted - zinc - bath with different length, depth, width, weight no more than 100 tons, and thickness 40 - 30mm, for example, flat, round, diamond, trapezoid or silo melted zinc baths, but the steel plates thickness must be from 50mm to 60mm

    二可根據用戶要求承接鋼板厚50 60mm各種長寬高鋼鍋槽板，鍋槽重不超過100噸的普通或異型鍍鋅鍋槽底部形狀各異。
  5. In the test of transmission coefficient property, semi - circle type, rectangle type, trapezoid type and concave type dyke are studied. research study is on the effect of relative water depth over the dyke to the transmission coefficient of the four different types dyke, and the comparison is done. finally, the experimental formula is given to the transmission coefficient, which are compared with the present formulae

    在潛堤透射特性的研究中，選取半圓型、矩型、梯型和槽型潛堤作為研究對象，在分析各個影響因素對潛堤透射影響的基礎上，選取最主要的影響因素，即相對堤頂水深作為研究的重點，分析研究了堤頂相對水深對四種結構型式潛堤透射系數的影響，比較分析了四種結構型式潛堤透射特性，在此基礎上，總結了計算潛堤透射系數的經驗公式，並與已存在的計算公式進行了對比，最後對潛堤的促淤效果進行了評估。
  6. The earth pressure over the pit bottom calculated by the trapezoid mode, and the result is better according with the rectangle mode of sandy foundation

    坑底以上樁側土壓力採用梯形分佈模式，計算結果與砂土地基的矩形分佈實測土壓力符合較好。
  7. This article details the arrangement relationship of independence, order, deflection order and the waterfall arrangement ways according to path number and running time, with the stress on the " trapezoid " arithmetic of batch process in parallel computer

    摘要介紹了含有獨立、順序、有偏序關系的批作業的梳理，以及批作業按作業序列路徑數、運行時間長短排序的瀑布式方法，重點講述了并行機批作業執行時的「梯形」演算法。
  8. Let be continuous and nonnegative on the closed interval. then the region bounded by the graph of, the - axis, the vertical lines, and is called the trapezoid with curved edge

    設在區間上非負、連續，由， ，以及曲線所圍成的圖形稱為曲邊梯形，其中曲線弧稱為曲邊。
  9. The results demonstrated that the weft tension and its amplitude can be effectively reduced and positively controlled to meet the requirements of weaving provided that suitable weft storage feed unit, weft feeding position and tension device are selected, modified trapezoid acceleration motion with smaller peak acceleration as the law of weft insertion motion is adopted, and the route of weft yarn motion is optimized

    結果表明：通過選用合適的緯紗儲緯器、張力器和緯紗供緯位置，選用加速度峰值較小的改進型梯形加速度引緯運動規律，優化緯紗運動路徑，可有效地降低緯紗的張力值和張力變化的幅度，達到對緯紗張力進行積極控制的目的，滿足織造工藝的要求。
  10. The ideal bemf waveform of bldcm is trapezoid with 120 ! platform width. in the 120 conduction mode, the stator current is not ideal due to the stator inductance, and the torque ripple occurs

    理想的永磁無刷直流電動機的反電動勢的波形是120平頂的梯形波，在三相六狀態120導通方式控制下，電流由於電機定子電感的存在而不是理想方波，因此產生了換相轉矩脈動。
  11. Fault location is an importrant function in distribuiton automation. in the thesis, the transferred information from feeder terminal unit is computed with load ’ s trapezoid fuzzy figure. the fault location is affirmed by the result of computation using the trapezoid fuzzy math theory. the atp and matlab softwares are used to simulate the 10kv lines in urmuqi distribution network. and the results shows the reliability and accuration of the method in the thesis

    線路故障定位是配電自動化的一項重要功能，文中提出利用線路始端電壓、電流和線路ftu （饋線終端單元， feederterminalunit ）的上傳信息，結合配電變壓器負荷的梯形模糊數模型，運用模糊數學理論通過電流計算來進行故障定位的新方法。
分享友人
分享到 Line

分享到臉書