treatment axis 中文意思是什麼
treatment axis
解釋
治療軸-
The nitriding is an important heat treatment process to boring axis in cnc floor - type milling / boring machine
摘要氮化處理是數控落地銑鏜床上重要部件鏜軸的常用最終熱處理工藝。 -
Moreover, the two - step heat treatment method was utilized in the preparation of the films, the films prepared by the first coating with 550 ? heat - treatment and the second coating with of with 500 ? heat - treatment ( b type films ) were highly c - axis oriented with smooth, dense and uniform surface morphology
此外，結合高溫和低溫熱處理方法優點的兩步熱處理法得到的b型薄膜同時具有較好的c軸擇優取向性和更為平整均勻的表面形貌。另外，在硅基板上也制備出了良好的c軸擇優取向性的摻雜氧化鋅薄膜。 -
Prepared technical parameters were optimized by l9 ( 34 ) experiment analysis. a unique method for cleaning and drying of substrate - cleaning used by scour, drying used by infrared light was fished out by large numbers of experiment. chemical mechnism of zno thin film prepared by sol - gel technique was discussed by dta for the first time. by the measurements of sem, xrd and uvs, the thin film was analysed. the result proved that the thin film with strongly preferred orientation of c - axis perpendicular to the substrate surface which surface was homogenous, dense and crackfree was the crystalline phase of hexagonal wurtzite. the thin film was composed of plentiful asteroidal crystal which crystal dimension approximately 10 30nm. the average transmittance of thin film in visible region was above 90 %. the results of measurements else also proved that the thickness of single dip - coating was 75 240nm, this films resistivity was found to be 3. 105 102 3. 96 105 ? cm. the thickness and resistivity of thin film influenced by dope - content, withdrawal speed, pre - heat - treatment, anealing were reseached respectively
利用xrd 、 sem以及uvs光譜儀等分析方法對薄膜進行了研究，結果顯示，所制備的薄膜為六方纖鋅礦型結構，具有高c軸擇優取向性；表面均勻、緻密，薄膜材料由許多星狀晶粒組成，晶粒尺寸大約為10 - 30nm左右；薄膜可見光透過率平均可達90 % ；對薄膜厚度以及電學性能進行了測定后發現：單次鍍膜厚度約為75 - 240nm ， al ~ （ 3 + ）離子摻雜型氧化鋅薄膜的電阻率在3 . 015 102 - 3 . 96 103 ? cm范圍內；分別研究了摻雜濃度、提拉速度、預燒溫度、退火溫度等工藝參數對薄膜厚度和電阻率的影響。 -
To the simplification of the kind of special medical treatment fiber, a study on the optical fiber at the output angle 90o relative to the central axis of the fiber is presented. this article includes the following segments : 1 the basic theories are offered which include the optical transmission theory in fiber and tilt effect on the fiber end
針對目前專用醫療輸出光纖品種較少的現狀，利用光纖金屬化:研磨-活化-鍍膜-熱處理等一系列成熟工藝，研製了一種可以改變光路、使激光束能沿著垂直光纖中心軸的方向輸出的一種新型的90o出光輸出光纖。
分享友人