triend model predistribution split model中文意思是什麼

triend model predistribution split model解釋
旅次端點運具分配模式

  • triend: 出行端點
  • model: n 1 模型,雛型;原型;設計圖;模範;(畫家、雕刻家的)模特兒;樣板。2 典型,模範。3 (女服裝店僱...
  • predistribution: 預先分配
  • split: n 斯普利特〈前南斯拉夫港市〉。vt (split;splitting)1 劈開,切開,割裂,扯裂;剖分。2 使分裂,使...

※英文詞彙triend model predistribution split model在字典百科英英字典中的解釋。

  1. The structure and operating principle of an air - charged split - type adjustable shock absorber was described, e non - linear parameterized mathematical model of this shock absorber ' s damping characteristics was established according to fluid mechanics theory and the main structural affection factors to shock absorber ' s damping performance, such as the diameter of piston valve orifice, the diameter of adjustable orifice, the initial volume of gas chamber, the diameter of piston rod, the inner diameter of oil pipe and so on, were analyzed by simulations

    摘要通過分析一種分體式充氣可調阻尼減振器的結構和工作原理,運用流體力學理論,建立了該減振器阻尼特性的非線性參數化模型,模擬分析了活塞阻尼閥孔徑、阻尼調節孔徑、氣室初始體積、活塞桿直徑、油管內徑等主要結構參數對減振器阻尼性能的影響,通過試驗測試,得到了減振器樣件的阻尼特性及其可調范圍。
  2. The flow field and pressure drops in the hydrocyclone were calculated numerically based on the k - e model modified for anisotropy and simple algorithm. the effects of operating parameters such as split ratio and feed flowrate on pressure drop were analyzed. the calculate results was compared with those obtained in experiment

    因此,本文採用各向異性-模型及simple ( semi - implicitmethodforpressure - linkedequations )演算法對水力旋流器內流場及壓力降進行了數值模擬,分別考察了溢流比、進料流量及溢流管幾何尺寸等對壓力降的影響,並把得到的數值計算結果與實驗值比較,證明本文的計算結果是可以接受的。
  3. Then this paper formulates a classification method of traffic modes, which accords to relation that different traffic modes affect mutually while moving. based on that classification of various traffic modes, this test proposes a combined modal split and trip distribution model of multinomial modes

    並根據各種交通方式運行時與小汽車流的相互影響關系,提出了交通方式分類方法,以此分類法為基礎,建立了聯合多方式劃分和交通分配模型,進行了等價性和唯一性證明,給出了模型演算法。
  4. 16 thousand kn j53 - 1600c model double - disc friction spiral press adopts international advanced structural configuration on its machine frame, that is split body with 4 - pull rod pre - stressing force structure

    J53 - 1600c型16000kn雙盤摩擦螺旋壓力機的機架採用國際先進結構形式,即分段機身四拉桿預應力結構。
  5. In order to overcome the shortages resulted from hypothesis of small deformation in radial symmetry based on thick - wall cylinder, plane stress and uniform pressure about residual stress around cold - expanded hole, a new model was proposed which takes into consideration the effect of split - sleeve, the different states along thick direction of specimen

    摘要針對目前在研究冷擠壓孔邊殘餘應力時,大都採用基於厚壁圓筒的軸對稱小變形、平面應力狀態、孔邊受力為均布載荷等假設所帶來的不足,提出了在三維真實模型狀態下,考慮襯套對孔邊受力的影響、試件在厚度方向上的應力差異等因素。
分享友人