trigger voltage 中文意思是什麼
trigger voltage
解釋
觸發電壓-
In the paper, on the basis of research of static state and transient state in the scr and series connection valve circuit, the high voltage scr changing current valve device has been developed for ac - dc - ac high voltage commutatorless motor. the series connection valve circuit has been designed and simulated. the hardware design and software programming of trigger pulse system and monitoring system in the photo - electronic - photo fashion has been completed
無換向器電動機在火電廠等工礦企業的電機調速節能領域中有十分廣闊的應用前景，本文在對晶閘管元件和串聯閥電路的靜態特性和動態特性研究的基礎上，研製了用於交直交電流型高壓無換向器電動機的高壓晶閘管換流閥裝置，進行了串聯閥電路的設計和模擬，完成了電光電方式的觸發脈沖系統和監測系統硬體設計及軟體編程，並進行了裝置的實驗調試。 -
The technology of alternating - current - boosting by way of constant current is successfully used to charge capacitors with 25 kilojoules of energy in only eight seconds. rail - gap switch with performances of long life and highly steady state are designed. and the high voltage pulse generator, which can produce low - excursion and fast - rise pulses, are designed by using double trigger circuit and hydro - thyristor as switch
在大功率恆流充電技術上，成功的應用了交流調壓式恆流技術，可以在8s內讓電容器儲存25kj的能量;設計出了長壽命、高穩定的軌道開關;採用氫閘流管做開關，使用雙觸發電路，研製出了低抖動、快前沿的高壓脈沖發生器（點火機） ;採用單片機和pld ，研製出了精度為10ns的延時同步機。 -
Using the digital technology improves the performance traditional thyristor welding machine, according to the characters of the double inverse star from rectifier circuit, set the parameters with micro - controller accurately, design the dependable trigger circuit, lead the feedback of voltage for the operation program, so the voltage of main circuit be carried out very steadily
摘要利用數字控制技術對傳統晶閘管焊接電源進行改進，根據雙反星型晶閘管整流電路的特點，採用單片機進行精確設定，設計了高可靠性觸發迴路，結合電壓反饋進行程序運算控制，實現了主電路輸出電壓的精確調整和可靠運行。 -
The control circuit of digitalized soft - starter with the three - phase ac voltage regulating was designed. the digital phase shifting trigger based on the 80c196kc mcs and gal16v8 programmable device was developed. the control method for digital phase shifting trigger was given and its principle of operation and designing was discussed
設計了三相晶閘管交流調壓數字軟起動器的硬體控制電路；研製了採用80c196kc單片機和gal16v8可編程器件構成的數字移相觸發系統；給出了數字移相觸發控制方法，分析和討論了該方法的工作和設計原理；採用了一種參數自整定的混合型模糊pid控制方法。 -
Most flashlamp applications use a trigger coil to produce high - voltage pulses of short duration, usually a few microseconds or less
大多數閃光燈使用一個觸發線圈產生瞬間高壓脈沖!其持續時間只有幾微秒或更短 -
The input voltage of the piezoresistive transducer, gain, sampling frequency and negative delay can respectively be graded through programming. the stored system is specially designed to have two modes of trigger ( namely, external trigger through wire breakage and inner trigger through overpressure signal ), reading software and interface circuit that are of
該測試系統可通過編程選擇傳感器供電電壓（兩檔） 、放大倍數（四種） 、采樣頻率（四種） 、負延遲（四種） ；同時具有斷線外觸發和超壓信號內觸發兩種觸發方式；讀數的軟體和介面電路都具有串併兼容特性；系統還具有狀態自檢和定時上電等功能。 -
High amplitude trigger pulse meets the power requirements of many thyristors connected in parallels. the voltage peak emerged in switching off inductance circuit is amortized by resistor and capacitor absorbed circuit
選取r = 54 ， c = 0 . 22 f的阻容緩沖吸收電路有效降低了快速晶閘管關斷感性負載產生的過電壓。 -
The module is composed of the vxibus interface, data acquisition and storage circuit, analog conditioning circuit and trigger control circuit. measurements such as period, frequency, voltage, pulse width are supported by the acquisition and storage of the input signals
該模塊主要由vxi介面電路，數據採集及存儲電路，信號調理電路和觸發控制電路等各部分組成，可以完成信號的採集、存儲，支持信號的周期，頻率，幅度，脈寬等參數的測量。 -
External triggering uses a high voltage trigger pulse to create a thin ionized streamer between the anode and cathode within the lamp
外部觸發使用高壓觸發脈沖在閃光燈的陽極和陰極之間產生一個較稀薄的電離流 -
As far as the choice of the 1c is concerned, the pfc and pwm controller combo that is popular at the present time is chosen, because it can simplify designs and being synchronized trigger mode adopted, it can make peak to peak ripple voltage much small even on the condition of small capacitance
在功率因數校正晶元的選擇上，選用了國際上比較流行的pfc pwm復合晶元，這種晶元不僅可以簡化設計，而且由於採用上升沿下降沿觸發方式，在輸出濾波電容很小的情況下依然可以得到很小的電壓紋波。 -
In the thesis, the detecting of current and voltage, selecting the sensor, designing peripheral circuit of microcomputer, power - semiconductor component, control circuit, trigger circuit and testing the software have been described in the more detail
作者在電壓、電流的檢測上，傳感器選型上，晶閘管的控制電路、觸發電路、單片機外圍電路的設計和選型上做了大量細致的工作。 -
The results show that the switch operates more steadily at trigger mode than at self - breakdown mode and its operating voltage range is related to such factors as the position of the trigger pin and gas pressure. it ' s also revealed that the switch has excellent operating characteristics, expecially low jitter and low misfire rate, when it operates at about eighty percent of self - breakdown voltage
研究結果表明：開關在自擊穿工作下的工作穩定性遠小於觸發工作時，開關工作范圍與觸發針位置和氣壓等因素有關；開關電壓選擇在自擊穿電壓的大約80 %時，開關抖動小、誤觸發率低，具有較好的工作特性。 -
A indirect fiber - trigger system is adopted for high voltage thyristor vale, which solves the problem of high voltage insulation and improves the capability against interfering and the reliability of the control signal. the thyristor gate electronics is also designed
論文採用間接光纖觸發方式作為高壓晶閘管閥的觸發隔離系統，很好地解決了系統的高低壓隔離問題，大大提高了控制信號的傳輸抗干擾能力和可靠性，並設計了相應的晶閘管門極電子電路。
分享友人