two-section method 中文意思是什麼
two-section method
解釋
雙段法-
In this section, applying the method, from abstract to specific and from history to present, it analyzes the operation mechanism of urbanization economy affected by market mechanism ; puts forward four theories of urbanization economy from economic perspective, including agriculture surplus and comparison advantage ; non - agricultural industry ; agglomeration economy and spillover effect, on this basis of the theories, it, on one hand, analyzes two kinds of internal mechanism in the chronologic operation of urbanization economies : increasing mechanism of urbanization economies in urban output industry ; and changing mechanism from specialization to integration, which are the representations of the evolution of " mart " development ; on the other hand, it analyzes two internal mechanism of dimensional operation of urbanization economy : internal spatial enlargement mechanism of urbanization economies from monocentric city to multi - center city, and external spatial enhancement mechanism which represents city - regionalization and city - chain connection, the later two mechanism represent the evolution of " polis " development
這一部分，按照由抽象到具體和由歷史到現代的研究方法，分析了市場機製作用下的城市化經濟運行機理，從經濟學角度提出了農業剩餘與比較優勢、非農產業、聚集經濟、外溢效應四大城市化經濟定理；在此基礎上，一方面分析了城市化經濟運行沿時間增長的兩個內在內容提要機制:城市輸出產業的城市化經濟增長機制和從專業化到綜合化的城市性質變遷機制，它們主要表現為「市」發展的延續;另一方面分析了城市化經濟運行沿空間增長的兩個內在機制:從單中心到多中心的城市化經濟運行的內部空間擴展機理和表現為城市區域化、城市連綿體的城市化經濟運行的外部空間擴展機理，它們主要表現為「城」發展的延續。 -
Section two the evaluation of biocompatibility of the acellular dermal matrix by the method of cell culture. the new born rat ' s epdermic cells were cultured with the acellular dermal matrix together as experiment group, while the epdermic cell were cultured simply as control. 24 hours later, under the invert microscope, the epidermic cells anchored well and transparent flat cells were observed in both groups. 7 days later, both cultured cells were taked out and fixed in 95 % ethanol, stained with hematoxylin and were observed under light microscope. many cleaved cells were observed in both groups. during cell culture, no pathogenic microganism was observed. so we considered the acellular dermal matrix was aseptic and had good biocompatibility. section three subdermal implantation of the acellular dermal matrix. 24 rats were used in the experiments. a piece of acellular dermal matrix ( 1. 5 x 1. 5cm2 ) was implanted beneath the dorsum skin flaps of each rat, 1 week, 2 weeks, 3 weeks and 4 weeks after implantation, 6 pieces of acellular dermal matrix were harvested and the size of implanted acellular dermal matrix were measured, the sections were used for he staining and observed under light microscope. the result were as folio wing : 1 - 2 weeks after implantation, the acellular dermal matrix began to adhere to the tissue around and turned red gradually ; 3 - 4weeks after implantation, the acellular dermal matrix adhered closely to the tissue around and could be recognized easily, 1 - 3 weeks after implantation, the size of implanted acellular dermal matrix had no statistical difference ( p > 0. 05 ). 4 weeks after implantation implanted acellular dermal matrix contracted ( p < 0. 05 ). under light microscope, l - 2weeks after implantation, the fibroblast cells infiltrated the acellular dermal matrix and a small amount endothelial cells of vessel and lympho - histiocytic cells infiltrated the acellular dermal matrix. 3 - 4 weeks after implantation, infiltrating blood vessels were evident. so we think that the acellular dermal matrix had low immunological reactions and could induce the infiltration of fibroblast macrophage cell and the endothelial cells of vessel
結果如下：皮下包埋卜周者，無細胞真皮基質漸與周圍組織粘附，顏色由蒼白轉紅；皮下包埋3周者，無細胞真皮基質與周圍組織緊密枯附，盾晰葉辯；術后卜周，包埋的基質面積變化較包埋前無統計學差異o川0引，術后4周包埋的無細胞真皮基質面積較包埋前縮小j刃刀5 ） 。光鏡下術后卜周，宿主的淋巳組織細胞、成纖維細胞浸入生長，釉附在膠原纖維上，少量血管內皮細胞浸入基質；術后34周，無細胞真皮基質內較多的血管形成，故可認為無細胞真皮基質免疫原性低，能誘導宿主的成纖維細胞、巨噬細胞浸入生長，為一種新型的真皮替代物。第四部分無細胞真皮基質與自體斷層皮片復合移棺的研究， sd大鼠10隻，在其背部卜方造成全厚皮膚缺損的創面 -
The basic theory and step of whole process analysis of reinforced concrete beam section flexural rigidity is stated, the realization program is worked out and the academic example is analyzed. 4. based on the static - state load test result of two practical projects, the application of the reinforced concrete beam system bridge structure disease examination and structure damage evaluation method is stated, and satisfaction result is gained
1 、綜述了當前混凝土橋梁結構檢測及損傷識別的各種方法體系，並簡要評價了各方法體系的應用與不足； 2 、論述了基於靜載試驗的梁分段剛度系統識別的基本原理，編制了實現程序，並進行了數值算例分析，提出基於本原理的梁橋結構損傷識別與結構評價方法體系； 3 、闡述了鋼筋混凝土梁截面抗彎剛度全過程分析的基本原理和方法步驟，編制了實現程序，並進行了相關算例分析； 4 、結合兩片工程實例梁的靜載試驗，詳述了梁橋結構損傷識別與結構評價方法的應用過程，得到了預期的效果。 -
Section ii describes the design approach and implementation of speech module on mcf5249 coldfire core. the speech codec optimizes g. 729a codes and added voice activity detection of g. 729b to save bandwidth ; the implementation of acoustic echo cancellation uses nlms algorithm and it can reduce echo though designing adaptive fir filter and speech detector ; the dtmf and cpt generate signal using two second order digital sinusoidal oscillators and detect signal by picking up the frequency information. but only get the frequency information is not enough in cpt detector, this thesis introduces a method
其中對語音編解碼器的設計採用優化g . 729a代碼達到設計要求，並在此基礎上加入g . 729b的靜音檢測模塊，以進一步降低網路傳輸帶寬;對回聲消除器的設計採用nlms演算法，通過設計自適應fir濾波器和語音檢測器達到回聲消除目的;對雙音多頻設計，信號發生端採用構造靜態參數表並通過二階正弦振蕩器產生信號，信號檢測端提取頻率信息以檢測信號;對呼叫進程音設計，除了類似雙音多頻的信號發生及頻率檢測設計外，還需要檢測信號持續時間，作者設計了一種基於匹配狀態表的方法以檢測信號持續時間。 -
The sea1 ring with complex section shape cafl be treated as a combined body made of several individual cy1 inders with di fferent dimensions. by app1ying the method used in the " edge prob1 em " of the fnoment theory of she11, the deformat ion - - - radia1 disp1acement and rotation at the two edges of each individual
應用殼體力矩理論中求解邊緣問題的方法，將密封環分解為多個等厚度、截面為單一矩形的筒體，對每一圓筒進行分析並運用殼體力矩理論求出其兩個邊緣在外載荷作用下的邊緣變形值? ?徑向位移及轉角。 -
The numerical simulation of axisymmetric two - dimensional shock tube is studied, which has a conical convergent section, and its driving gas is the hot product of hydrogen oxygen detonation. finite volume tvd scheme is adopted and the mesh is local orthogonal. the primitive equations are euler s equations of multi - component flow. the new method of eliminating numerical oscillation at the interface of two materials is extended to two dimensions. the mechanical character of this shock tube is analyzed
對由前向爆轟產生驅動氣體並具有局部錐形收縮截面的軸對稱激波管利用兩相常比熱完全氣體的歐拉方程組和有限體積tvd格式在局部正交的網格上進行了二維數值模擬。將消除兩種介質界面處數值振蕩的新方法成功地推廣到二維情況。分析了該激波管的力學特性。 -
This section firstly discusses divergence of views in academic circles of china, and, rejecting the former method of research on the instigator that did not differentiate whether the instigated committed the crime of instigation or not and distinguishing the two cases of instigation, redefines the scope and nature of the instigator
這一部分從我國學界認識上的分歧談起，拋開了學界過去研究教唆犯不分被教唆者犯與沒犯被教唆之罪而籠統地對教唆犯研究的方法，釐清了教唆犯的兩種不同情況，對教唆犯的范圍、性質進行了重新定位。 -
In order to achieve the optimized tunneling approach, first, tunneling procedures, shift length, horizontal jet grouting length, bench length and space length between c and d part of crd method are optimized ; on the basis of these results, two kinds of tunneling schemes are calculated with three - dimensional fem and the optimized tunneling scheme is achieved. as results of the optimized scheme, the conclusion is made that the gas pipe above the tunnel of sk3 + 355 section is secure. the calculation results are verified through comparison of numerical simulation results and site - monitoring measurement data
為得出適合本段工程的最佳施工路線，利用大型有限元通用軟體ansys對開挖順序、開挖進尺、水平旋噴長度、臺階長度及crd工法施工的c 、 d部相錯長度進行了有限元數值模擬和優化分析，並利用這些分析結果，進行了兩個施工方案的三維有限元動態施工模擬，得出了較優的施工方案，並利用施工后的地表沉降槽曲線，對sk3 + 355斷面處隧道上方的煤氣管線的安全性進行了分析，得出了利用此施工方案施工不會造成此處煤氣管線破壞的結論。 -
Establish is in high school mathematics the teaching is the physically, and pass two academic associations of " s " rationality of deep mathematics that education that the teaching ' s reformation, gradually to high school mathematics the teaching practice to proce ed the anti to think with the improvement, and make the teacher have the higher theories cultivated manners to educate the theories, the stronger section study the consciousness the with modern the with the the section to study the ability, aware of self make use of forerunner to thought to guide with method to practice, most the attain to enhance student mathematics the cultivated manners, and educate the student creative ability, increase to educate the purpose of the teaching quantity
數學思維能力的培養是中學數學教學的核心，探求中學數學課程的發展過程，對中學數學教學實踐進行反思與改進是中學數學教與學研究的出發點。立足於中學數學教學實際，通過「兩個學會」深化數學教學的改革，逐步對中學數學教學實踐的合理性進行反思與改進，使教師具有較高的理論素養，較強的科研意識和科研能力，自覺地運用先進的教育思想和方法指導實踐，最終達到強化學生數學素養，培養學生創新能力，提高教育教學質量之目的。 -
Fabrication of the box beam is divided into such parts as reinforcement, formwork, concreting, prestressing, moving and storing of beam, pipe grouting under pressure, end sealing of the beam, water - proof layer on the bridge surface system, protective coating etc. the paper makes description of effective box beam construction technology and workmanship which can be adopted in other projects, such technologies as : manufacturing and fixing of reinforcement, steel reinforcement fixing baseplate, web plate and top plate respectively and lifting the steel skeleton into form, requirements of design and manufacturing and way of utilization for dismantling - erection type formwork and hydraulic formwork, optimization of concrete ratio, concrete pouring process of two ends of beam in priority over the middle, in sequence of first baseplate followed by web plate and top plate at last, concrete pouring in inclined section and in horizontal layer, concrete vibration mainly by external vibrator in assistance with internal vibrator, methods and regulation for steam curing of concrete, dual controls over stress and strain to ensure quality of prestressing workmanship, construction method of effective beam moving by heavy - weight special moving facility, some regulations and key notes about construction of grouting under pressure, beam ends sealing, water - proof layer on the bridge surface system, protective coating
箱梁製造由鋼筋工程、模板工程、混凝土工程、預應力工程、移存梁工程、孔道壓漿工程、梁體封端工程、橋面防水層和保護層工程等施工環節組成。文中介紹的採用胎具製作和綁扎鋼筋，分底腹板和頂板分別綁扎並吊裝鋼筋骨架入模；拆裝式和液壓式兩種模板的設計、製作要求和使用方法；綜合考慮、優化混凝土配合比，混凝土灌注從兩端至中間、先底板、后腹板、再頂板的施工順序和斜向分段、腹板水平分層、附著式振搗為主、插入式搗固為輔的施工工藝，蒸汽養護的方法和規定；應力應變雙控制確保預應力施工質量的施工技術；採用重物移運器有效移梁的施工方法；壓漿、封端、橋面防水層和保護層施工的一些規定和注意事項等都是對箱梁製造行之有效的施工技術和施工方法，並可為以後類似施工作借鑒。 -
Considering that the characteristics of our country ' s highway tunnels are always of long spans, tabular and of various geometry, by means of thorough analysis of the different problems existed in the design of support structures of the tunnels at present, this paper pays special attention to the two key problems, optimization method of form selection of structural section of the tunnel as well as the stability and bearing capacity of the support structures, in the design of the long and large tunnel on high - class highway, introduces the simplified complex - form optimum method in the structure optimization theory, discusses the optimum design model of lining section of highway tunnel with satisfying demands in building clearance, ventilation and load conditions, puts forward an optimization method of form selection of three different kinds of lining sectional forms ( i. e. single - center circle, three - center tabular circle and three - center sharp circle ), establishes a complete set of systematic optimum design the ory and method of long and large tunnel on high - class highway, develops the corresponding computer software used on the planned xuefeng mountain highway tunnel on shaoyang to huaihua expressway in hunan province for optimization of form selections of the structural sections, and obtains a series of relatively reasonable structural design parameters
本文針對我國公路隧道多為大跨度、扁平、幾何形狀呈多樣化的特點，通過深入分析目前隧道支護結構設計中存在的各種問題，抓住高等級公路長大隧道設計中隧道結構斷面的優化選型及隧道支護結構的穩定性與承載能力兩個核心問題，引入結構優化理論中的簡易復合形優化方法，深入探討了滿足建築限界、通風條件、受力狀態約束等條件下公路隧道襯砌斷面優化設計模型，提出了三種襯砌斷面形狀（單心圓、坦三心圓和尖三心圓）的優化選型方法，建立起一套完善的高等級公路長大隧道的系統優化設計理論與方法，並開發出相應的計算機程序，用於擬建的上海至瑞麗國道主幹線湖南省邵陽至懷化高速公路雪峰山長大高速公路隧道的結構斷面優化選型，得出了一系列較為合理的支護結構設計參數。 -
By default, the 1. 4. 1 jdk divides the heap into two sections, a young generation and an old generation. actually, there is also a third section, the permanent space, which is used for storing loaded class and method objects
在默認情況下， jdk 1 . 4 . 1將堆分為兩部分，一個年輕的代和一個老的代（實際上，還有第三部分永久空間，它用於存儲裝載的類和方法對象） 。 -
A analysis of these effect to the pattern is presented. in the mean time, the method of correcting the phase errors is given by shortening or lengthening the section of sinuous feed line between couplers from the normal value. 6. the reflection characteristic of a serpentine is analyzed where the coupler is replaced by the equivalent of two ports loss network
提出了用有耗二埠網路來等效波導耦合器的方法，對由耦合器、饋電波導和波導彎頭級聯的慢波線系統的駐波特性進行了分析計算，針對慢波線在設計測射頻率上大反射問題，討論了多種解決辦法。 -
In section one, we get the boundedness in terms of two measures for impulsive hybrid systems using lyapunov ' s direct method
1主要利用lyapunov直接方法得到脈沖混合系統的關于兩個測度的有界性結果； 53 -
In this paper the basic principle of the method of characteristics is described, and is constructed an explicit scheme for dam break simulation of one - dimensional dam instant all break waves flow of a low dam with rectangle section and a huge dam with trapezia section, and of two - dimensional dam instant part break waves flow with simplest space operator splitting
本文模擬了一維矩形斷面低壩和梯形斷面巨型壩瞬間全潰的洪水波演進過程，給出了與分析解的比較，並結合運算元分裂的特徵線法對二維瞬間部分潰壩時洪水波的演進過程進行了數值模擬。 -
Many factors regarding the modifying coefficients of circular and rectangular section are analyzed : ( 1 ) it is theoretically proved that the diffusion coefficient of cl - in concrete is dependent of modifying coefficients ; ( 2 ) through analysis of the results of numerical value calculation, it is discovered that the relation between the modifying coefficients and the thickness of protection layer of concrete is linear, from which the function expression of these two variables is gain ; at the same time, the influence on modifying coefficient of the radius of circular section and the thickness of cl - on the surface of concrete ; based on these, practical calculating method of beginning corrosion time of steel of circular section is set up ; ( 3 ) to rectangular section, the diffusion of cf in concrete is two - dimension diffusion
討論了影響矩形截面以及圓形截面修正系數的因素： （ 1 ）從理論上證明了氯離子在混凝土中的擴散系數與修正系數無關； （ 2 ）通過圓形截面數值計算結果的分析，發現圓形截面修正系數與保護層厚度基本成線性關系，並建立了二者之間的聯系；分析了圓形截面半徑、混凝土表面氯離子濃度對修正系數的影響，從而建立了圓形截面鋼筋初始銹蝕時間的實用計算方法； （ 3 ）在矩形截面氯離子侵蝕下，混凝土處於二維擴散狀態。本文通過計算分析，證明二維擴散的影響區域從邊角開始向中間逐步擴散，並證明了二維擴散影響區域依賴于氯離子擴散系數與氯離子擴散時間的乘積。 -
In the aspects of choice that make the price method, because of canning compare the company analysis method with can compare the bargain analysis method must have the prosperous capital market, more case example, lack domestic current the bargain of the state - owned property to say, very much the enough case example props up. and buy the market multiple analysis method analyze first public of and buy the market bargain multiple, and usually is trading the scale to ascend to take into the restrict with the industry category, for example, can be provided as analytic bargain a bargain for being limited by this front in six months, target company in the electric power profession, the scale limit in 50, 000, 000 dollars including, this kind of method and ca n ' t provide the help of high times. but the dividends usuallies convert into cash to analyze the method to get the analysis of the bonus from the target company to the value that get the target company. the above method exsits current state - owned property make price very much the localization of the different degree, the past a text tries to use value analysis method as to lends support to the method, the cash discharge converts into cash to analyze method ( the method of dcf ) as the main method, the certain state - owned property procures the price. among them, use the cash discharge converts into cash to analyze the method makes sure the income is after procuring, value analysis the method gets of result the conduct and actions manages with state - owned property the section to make the basis of the price for the state - owned property, two kinds of methods is mutually combinative, make sure the state - owned property procure the price
以上方法對于目前國有資產的作價都存在不同程度的局限，故本文嘗試用賬面價值分析法為輔助方法，現金流量折現分析法（ dcf法）為主要方法，確定國有資產收購價格。其中，用現金流量折現分析法確定收購之後的收益，賬面價值分析法得到的結果作為與國有資產管理部門就國有資產作價的依據，兩種方法相互結合，來確定國有資產收購價格。同時論文對國有企業收購整合的模式作了積極的探索，地方電力公司投資新的水利發電項目往往同時有一部份是排灌、防洪等非經營性的，或稱為公益性的無收益項目，論文對新建項目的經營性資產與非經營性資產合理比例作了深入的探討，重慶大學碩士學位論文並建立了分析模型，對于新項目的投入資金結構進行了較為深入的分析，並建立了相應的項目融資模型。 -
In order to effectively use the vacant space beside the passenger train paths in the train running diagram of mixed passenger and freight lines and draw more freight train paths to improve the carrying capacity, the essay analyzes the reasonable drawing plan for freight train paths beside single passenger train arid two passenger trains respectively on the double tracked section with automatic blocking system according to the principle of minimal additional removal time and on the basis of the calculation method of removal coefficient table
摘要為了在客貨共線運行圖中有效利用旅客列車運行線兩側的空檔，盡可能多地鋪畫貨物列車運行線，以提高區段通過能力，在扣除系數表格計演算法的基礎上，按照附加扣除時間最少的原則，分析了在雙線自動閉塞區段單列旅客列車和2列旅客列車兩側貨物列車運行線的合理鋪畫方案。 -
The paper applies each section of fund circle and turnover, and analyies the kinds of financial exposure and relative effect factors of financial exposure extent. it uses gradation analysis method to create the model - components regression forecast model to facilitate to evaluate it comprehensivly from two aspects of quantity and quality analysis. by the model, we may find out primary factors of affecting financial states of compaany, and manage and control financial exposure objectivly
本文按照企業資金循環與周轉的各個環節，從定性分析和定量分析兩個方面分析財務風險的種類及影響財務風險大小的相關風險因素，並從我國企業的實際情況出發，運用層次分析法建立了有利於綜合評價我國企業財務風險的模型? ?多元回歸預測模型，通過該模型，可以找出影響企業財務狀況的主要因素，從而有針對性的管理與防範控制財務風險。 -
There are commonness and individuality between subdivision surface and spline surface, based on the research of the algorithm of nc tool path generation for spline surface, used in conjunction with subdivision property, two methods : cross - section method and projecting method are put forward. ( 4 ) subdivision surface is quite adaptive to arbitrary topology, so the subdivision surface reconstruction techniques has also received much attention
細分曲面和樣條曲面既具有共性，又各有個性，本文通過對樣條曲面數控加工刀軌生成演算法進行研究，同時根據細分曲面本身具有的特性，給出了採用截平面法和投影法生成細分曲面數控加工刀軌的演算法。
分享友人