ultimate modulus 中文意思是什麼
ultimate modulus
解釋
極限模量-
According to elasto - plasticity theory, with the help of finite - method program ansys, the paper undertakes the computer analogue tests about the bearing capacity of pile tip arranged by orthogonal principle, and attains the relations of pile - tip bearing capacity to embedment depth, pile diameter, cohesion, internal friction angle and modulus of deformation. by the means of mathematical statistic, regression equation of the ultimate bearing capacity calculated by finite element method is gained through the regression analysis of 81 group data from the computer analogue tests. by comparison and analysis of the values calculated by finite - element regression equation and the values of in situ loading test, the regression equation is gained which calculates the size effect for base resistance of large diameter pile
根據彈塑性理論，運用大型有限元軟體ansys按正交設計理論對樁端承載力進行模擬計算，獲得樁端承載力與樁長（埋置深度） 、樁徑、粘聚力、內摩擦角及變形模量等主要影響因素的關系，並採用數理統計方法，對81組ansys模擬試驗結果數據進行回歸分析，得到有限元法確定樁端極限承載力的回歸公式，並將有限元法回歸公式計算值與現場小壓板載荷試驗值進行比較分析，得到大直徑樁端阻的尺寸效應系數計算公式。 -
The static triaxial test of two engineerings shows that the breaking strength of asphalt concrete declines significantly as the temperature rises and the strain increases noticeably when breaking. increase in the asphalt content leads to decrease in tangent modulus and cohesion, but the internal friction angle tends to increase. increasing confining stress results in the augment of the maximum stress and the ultimate value of volumetric strain
兩個實際工程的靜三軸變形與強度試驗表明，隨著溫度升高瀝青混凝土破壞強度明顯降低，破壞時應變明顯加大；瀝青含量的增加會導致切線模量和凝聚力降低，但內摩擦角趨于增加；周圍壓力增大會導致最大應力_ d增大，其體變壓縮極限值也越大。 -
On the basis of relative researches in the world, according to the study status of steel - concrete composite slab, which would be widely used in modern bridge, modified equivalent inflexibility of steel - concrete composite slab was deduced by use of conversion section principle in this paper ; based in this, this paper put forwards the theory of ultimate flexural capacity of steel - concrete composite slab in consideration of slip effect, and introduces the practical simplified method for calculating flexural deformation of steel - concrete composite slab in consideration of the effect of steel studs and welded wire, and conclude that the methods in this paper is veracious and reliable, comparing with the traditional calculating mode ; morever, this paper put forwards the calculating theory and program of the effect analysis of creep and shrinkage to steel - concrete composite slab, using conversion elastic modulus principle, and testifies that the theory is right and the program is reliable and practical
本文在國內外研究成果的基礎上，針對壓型鋼板與混凝土組合板結構在現代橋梁建設中廣泛應用前景和研究現狀，利用換算截面法導出了壓型鋼板與混凝土組合板結構的修正等效慣性矩；在此基礎上，又推出了考慮壓型鋼板與混凝土之間的相對粘結滑移影響的壓型鋼板與混凝土組合板結構極限抗彎承載能力計算理論，並介紹了考慮栓釘、聯結件影響的壓型鋼板與混凝土組合板結構簡化實用撓曲變形計算公式，而且通過與傳統計算理論的分析比較，表明本文提出的計算理論公式的準確可靠性；此外，採用換算彈性模量比法著重提出了壓型鋼板與混凝土組合板結構的徐變、收縮效應分析的計算理論和程序，並通過實例分析計算證明了理論的正確性、程序的可靠性和實用性。 -
The multi - purpose tester developed here is aim at testing the mechanics performance of the brittle material, which bases on modular design thought, it contains several modules as the machinery load component, platform of supporting, the function modules and the software system, they can be combined in different function modules to satisfies the need of different application situation. the tester can be used to measure not only general material properties such as elastic modulus, ultimate strain, strength, hardness and toughness, fatigue properties but also various special properties such as the local strength, and surface residual stress at the different location of the brittle component with non - destructive methods. thus the security and reliability of the brittle component can be evaluated and predicted
本文基於模塊化設計思想，研製了一臺專門針對脆性材料力學性能測試的多功能脆性材料試驗儀，其主要包括機械加載模塊、支撐平臺、功能模塊、測控系統、軟體系統等模塊，通過對這些模塊的不同組合可實現不同的功能及滿足不同應用場合要求;系統除了具有測試脆性材料的彈性模量、極限應變、強度、硬度、韌性等常規性能外，還具有無損測試玻璃構件不同位置的局部強度和表面預應力，進而對玻璃構件的安全可靠性和壽命進行預測等功能。 -
1. experiments on uniaxial tensile of cfrp and gfrp are carried out, in which the tensile strength, young ' s modulus and ultimate deflection of frp are measured. the influence on tensile behavior caused by different adhesives is analyzed, and the standardization problem on tensile test methods is discussed
設計了加載裝置和測量應變裝置，測試6種不同纖維片材和粘結劑組合的抗拉強度、彈性模量、極限應變，並分析不同粘結劑對纖維片材拉伸性能的影響，最後對纖維片材拉伸試驗的標準化問題進行了簡單的探討。
分享友人