vs heat 中文意思是什麼
vs heat
解釋
精采表現-
The adsorption isotherm of neptunium on silica gel correspond to the form of langmuir isotherm. according to clausius - claperon equation, from the slope in inkd vs 1 / t plot, adsorption heat could be estimated. from the data of adsorption heat it is concluded that the adsorption of neptunium on silica gel in nitric acid solutions belongs to chemical adsorption and the adsorption process is an endothermic reaction
三種價態的鎿在硅膠上吸附的等溫線符合蘭格繆爾吸附等溫線的形式，是單分子層吸附；根據克勞修斯-克拉柏龍方程，以1nkd對1 t作圖，通過直線斜率計算出吸附熱，從吸附熱的數據可判斷三種價態的鎿在硅膠上的吸附屬于化學吸附，是吸熱的過程；對npov ） 、 np （ v ）和np （ vd在硅膠上的吸附進行了比較，提出了三種價態的鋒在硅膠上吸附的機理。 -
By comparing the results with relative experiment data, it is shown that rng k - is more exactly than the other turbulent model. 2 ) the influences of axial inflow position, radial outflow size, rotating reynold number, non - dimensional mass flowrate and axial inflow angle on the flow and heat transfer characteristics were numerically investigated for a typical rotator - stator cavity with axial inflow, radial inflow and radial outflow. the correlations for average nusselt number vs rotating reynold number or non - dimensional mass flowrate were established
（ 2 ）針對一典型的徑向、軸向進氣，徑向出氣的轉-靜盤腔結構，系統研究軸向進氣位置、徑向出口大小、旋轉雷諾數、無量綱質量流量和軸向垂直預旋進氣等對盤腔內流動和換熱的影響，整理出轉-靜盤腔內轉盤平均努謝爾數與旋轉雷諾數無量綱質量流量之間的準則關聯式。 -
4 ) in a pre - swirl rotator - stator cavities with discrete pre - swirl nozzles and blade - cooling entry holes, the influences of pre - swirl angle and flow parameter on the flow and heat transfer characteristics were numerically investigated. the correlation for average nusselt number vs rotating reynold number or non - dimensional mass flowrate were established. the results show that : advantage of per - swirl inflow is the effect of cooling the blade - cooling entry holes ; pre - swirl inflow increases heat transfer in rotating disk of pre - swirl chamber ; as pre - swirl angle increases, local nusselt number decreases in pre - swirl chamber ; the temperature of stator of inner rotator - stator chamber and per - swirl chamber decreases as rotating reynold number increases ; when the axial mass flowrate maintains constant, heat transfer in the rotating disk of inner rotator - stator cavities does n ' t change as per - swirl mass flowrate increases, while heat transfer in the rotating disk of per - swirl chamber increases ; when the pre - swirl mass flowrate maintains constant, change of the axial mass flowrate has effect on the whole cavity
結果表明，預旋進氣的優點在於增強了葉片冷卻孔附近的對流換熱效果，局部努謝爾數隨預旋角的增大而有所減小；隨旋轉雷諾數的增加，不論是內轉靜腔室還是預旋腔室的靜盤上的溫度都不同程度的降低：當軸向中心進氣質量流量不變時，隨預旋進氣的質量流量增加，內轉靜腔室的轉盤盤面上的換熱基本沒有變化，而預旋腔室的轉盤盤面上的換熱效果增強；當預旋進氣質量流量不變時，軸向中心進氣的質量流量的改變對整個盤腔都有影響。 -
Smooth tempered glass is manufactured by heating up float glass to swiftly and uniformly, with this special heat treatment and quenching process which increases glass strength up to four to five times vs, annealed glass, in case stresses beyond its capacity, smooth tempered glass simply disintegrates into innumerable small pieces, significantly reducing the risk of serious injury
鋼化玻璃是將浮法玻璃經過物理性淬火處理，使其表面形成均勻的壓應力，而內部則形成張應力，從而有效的提高了玻璃的抗彎和抗沖擊性能，強度達到了普通玻璃的3 - 4倍，當其破碎時則分裂成均勻純角不易傷人的小顆粒，使其成為一種現代生活中理想的安全玻璃。 -
The performances such as air flow, airside pressure drop, waterside heat exchange and power consumed by compressor vs. frosting time under different condition, were simulated and analyzed by using the ashpwch model developed
採用該模型對機組在不同工況下的性能進行了模擬分析，得到了風量、空氣側壓降以及水側換熱器換熱量、壓縮機的軸功率等隨結霜時間的變化。 -
The sensor is calibrated, then the relative curve of heat flux vs thermal voltage is determined. moreover, the test of responses of steady state and transient state has been done and the results are compared with predecessors ? results, and proved to be advanced in response speed
在此基礎上對薄膜熱流計進行了穩態響應測試和瞬態響應測試，並與國外的結果進行了比較，結果表明，該熱流計在響應速度方面較快，在靈敏度方面稍低。
分享友人