wafer type 中文意思是什麼

wafer type 解釋
對夾式（薄片型）
  • wafer : n 1 薄脆餅；薄餅一樣的東西；【物、無】圓片；薄片；晶片；【醫學】糯米紙〈包藥用的干糊片〉。2 （封...
  • type : n 1 型，類型，（工業產品的）品種；風格，型式。2 典型，榜樣，樣本，樣板，模範，範本；典型人物；具...
  1. Conductivity type - the type of charge carriers in a wafer, such as “ n - type ” and “ p - type ”

    傳導性（電學方面） -一種關于載流子通過物質難易度的測量指標。
  2. To find out the effective slurry with suitable type of oxidizer and concentration, chemical etching experiment was applied to the litao3 wafer. the chemical etching effects were analysed by measuring etching rate and x - ray spectrum

    採用化學腐蝕實驗方法研究拋光液中氧化劑種類和濃度以及拋光液ph值對鉭酸鋰晶片化學去除的影響。
  3. Wafer type rubber - seated butterfly valves

    圓片形橡膠座節流閥
  4. However, to minimize the maximum completion time for the wafer probing scheduling problem ( wpsp ) is very important for equally utilizing the capacity of parallel - machine, while satisfying the requirements of product types, product family, sequence dependent setup time, product - type dependent processing time, due dates of jobs, and capacities of machines

    然而求解晶圓針測排程問題最大完工時間的最小化以均勻的利用平行機臺的產能是非常重要的，該問題尚考慮以下的問題特性：產品別與產品族、順序相依設置時間、決定於產品別的工作處理時間、工作交期與機臺產能限制等。
  5. The cmp experiment was carried out systematically on litao3 wafer. the polished surface foughness and material removal rate in different polishing conditions were measured and the effects of polishing pad material and its condition, pressure, rotating speed of the polishing plate, the type and size of abrasive, and the properties of the polishing slurry on the surface routhness and material removal rate were analysed in details

    通過對鉭酸鋰晶片的化學機械拋光過程的實驗研究，通過測量鉭酸鋰晶片在不同拋光條件下的表面粗糙度和材料去除率，詳細分析了拋光墊材料和狀態、拋光壓力、拋光盤轉速、磨料種類及粒度、拋光液組成等幾個因素對拋光表面質量和材料去除率的影響規律。
  6. The main contents of the thesis are as following : ( 1 ) thermal neutrons irradiating the silicon wafer gives rise to fractional transmutation of silicon into phosphorus and dopes the silicon n - type. the method of p - type doping zno by proton transmutation doping was presented by reference to that of the silicon

    本論文的主要內容和結果如下: （ 1 ）借用「熱中子輻照矽片使部分硅嬗變為磷，從而將硅摻雜成n型」的思想，從質子嬗變角度討論了實現zno材料的p型摻雜方案。
  7. Wafer type butterfly valves with rubber itning

    對夾式襯膠蝶閥
  8. Specification for steel and copper alloy wafer check valves, single - disk, spring - loaded type

    彈簧加載型鋼和銅合金單盤壓片止回閥規范
  9. Secondary flat - a flat that is smaller than the primary orientation flat. the position of this flat determines what type the wafer is, and also the orientation of the wafer

    第二定位邊-比主定位邊小的定位邊，它的位置決定了晶圓片的類型和晶向。
  10. Wafer type check valve

    對夾式止回閥
  11. Wafer type check valves

    板式止回閥
  12. Wafer type component

    圓片型元件
  13. Ships and marine technology - butterfly valves for flanges extra light duty wafer type and flanged type - dn 50 to dn 125, pn 10

    船舶和航海技術.法蘭連接的超輕型晶片式和有法蘭的碟
分享友人
分享到 Line

分享到臉書