wall ratio 中文意思是什麼
wall ratio
解釋
壁厚比-
Cleanup corrosive substance in pipe such as internal water, clean oil, methane hydrate, ferric oxide, carbide dust, carbon bisulfide, hydrosulphurice acide, etc. ; reduce corrosion damages to inner wall of pipeline caused by corrosive substance ; clarify pipe route again ; inspect pipe deformation ; check perfectness ratio of valves along pipe ; decrease working backpressure
清除管線內部積水、輕質油、甲烷水合物、氧化鐵、碳化物粉塵、二硫化碳、氫硫酸等腐蝕性物質；降低腐蝕性物質對管道內壁的腐蝕損傷；重新明確管線走向；檢測管線變形；檢查沿線閥門完好率；減小工作回壓。 -
For reinforcement concrete corbel with the shear span to depth ratio ( a / ho ) less than 1, has its performance of mechanics that is close to cantilever deep beams, it is an important kind of components in architectural structure which sustains roof trusses, brackets, tray " beams, frame " beams, wall " beams and crane " beams
剪跨比a h _ 0 1的短鋼筋混凝土牛腿，其受力性能接近於懸臂深梁，在建築結構中是支承屋架、屋面梁、托架、托架梁、框架梁、墻梁和吊車梁等的重要構件。 -
Considering the special structure of multi - ribbed slab, founding diphase body mechanical model of compound material, strengthening rib beam and rib pillar by equivalent volume ratio of concrete and slice brick, the paper drew elastic compution constant and shear constant. based on the things, the paper simplified isotropy compution model to wall, gave practical design formula of elastic mold and shear mold, provided necessary parameter for practical design formula of elastic rigidity. finally the calculating results agree well with the text results
結合密肋復合墻板的特殊構造，建立墻板的復合材料二相體力學模型，按照混凝土與砌塊體積比不變原則對肋梁肋柱同時加強，得出墻板的彈性計算常數及剪切常數，在此基礎上，進一步將墻板簡化為各向同性的計算模型，給出墻板彈性模量及剪切模量實用計算公式，為密肋復合墻板的實用彈性剛度計算公式提供必要的參數。 -
Based on the numerical simulation and accuracy analysis to previous slab ' s test with the ansys program, the study of composite wall, with various detail design under potential load action respectively or jointly is carried on and the wall ' s atress behavior and failure mode is obtained, also the influence to wall ' s stiffness and bearing capacity by kinds of factors, including wall ' s shear span ratio, member ' s section, bar arrangement, etc. based on the hammer blow test and stiffness test, a 1 / 3 scale ten - bay model ' s modality parameter and elastic deformation characteristic is analyzed
在對密肋復合墻板運用ansys ~ （ （ ? ） ）程序進行數值模擬、分析驗證的基礎上，對典型組合墻體在不同連接構造和不同荷載效應組合作用下的受力形態和破壞模式進行研究；計算分析了復合墻體剪跨比、邊框柱截面尺寸、邊框柱配筋大小以及墻板內肋梁肋柱配筋等諸多因素對密肋復合墻體承載力及剛度的影響，得出其變化規律。 -
The temperature rise at the center of a massive concrete wall is calculated by using the adiabatic rise of temperature and heat conduction equations of concrete based on the equivalent time, and considering effects of temperature on the hydration heat reaction ratio and creep characteristics of early - age concrete
摘要基於等效時間的混凝土絕熱溫升、熱傳導方程，考慮溫度對早期混凝土水化熱化學反應速率和徐變特性的影響，計算了大體積混凝土墻中心的溫升。 -
The regularities of pile - top reaction distribution, the carrying load ratio between pile and raft, the settlement and the imparity settlement of foundation in the frame - tube structure and the single wall are influenced by some factors such as the stiffness of the superstructure, the intensity of the soil under the piles, the length and radius of the piles, the distance between the piles, the thickness and the suspended width of the raft
對豎向荷載作用下的空間筒中筒結構、樁筏基礎和地基進行了三維有限元分析。研究整體結構和單片墻結構在上部結構剛度、樁端土強度、樁長、樁徑、樁距、筏板厚度、筏板外挑寬度等影響因素變化時的樁頂反力分佈規律、樁筏荷載分擔比、樁基沉降和差異沉降規律。 -
In this thesis hydraulic experimental studies and theoretical analyses on the vortex - flow drop shaft were conduced and the following results were accomplished : ( 1 ) in the model test some hydraulic characteristics including the shape of air core in the center of the drop shaft, the radial distribution of water flow velocity and the distribution of pressure on the wall of the drop shaft were measured under the condition of high water head above 250m and large discharge above 1400m3 / s. ( 2 ) a kind of computational method for the spiral water flow in the air core region of drop shaft was discussed and applied and the results agree the experimental data well. ( 3 ) the total ratio of energy dissipation in the drop shaft can reach 90 % and the energy dissipation in every region was discussed quantitatively
本文通過試驗研究與理論分析對旋流式豎井泄洪洞應用於高水頭、大泄流量情況時存在的一些水力學問題進行了研究和探討，取得以下主要成果：一、結合小灣工程導流洞改建，對高水頭（ 252m ） 、大泄流量（ 1400m ~ 3 s ）條件下旋流式豎井中的水流運動特徵進行了比較全面的測量，包括空腔形態、徑向流速分佈及井壁壓強等；二、提出了豎井空腔段螺旋水流水力計算方法，其計算結果與實測值吻合良好；三、利用試驗與計算結果，對旋流式豎井的消能機理進行了探討，對豎井各部分的消能能力有了總體認識；四、對豎井下部消力井的合理井深進行了優化試驗研究，發現消力井合理深度為0 . 9d左右；五、通過試驗研究，歸納出豎井水流總摻氣量估算方法，為導流洞排氣方案的設計提供了參考依據；六、在高水頭、大流量條件下，豎井空腔段下部流速很高，盡管水流螺旋運動引起的離心力可以確保井壁壓強保持正壓，但空化數依然較低，因此豎井的空化空蝕始終是工程界關注的重大問題。 -
The thermal visualizations of jet impingement cooling with single or double row holes inside semi - enclosed channel are measured by using infrared camera and then the impingement cooling heat transfer coefficients are deduced. the effects of flow and geometry parameters on convective heat coefficients are obtained. the results show that : for a single row normal impingement, the impingement cooling effectiveness is enhanced with the increase of impinging reynolds number or the decrease of hole space to diameter ratio, and the best effectiveness is achieved under the jet - to - surface spacing equals to 2 ; when the jet is oblique to the confined wall, the cooling effectiveness is weaken especially under the jet - to - surface spacing ratio is greater than 2 ; for double rows normal impingement cooling, the cooling effectiveness of rear row jet is weaker than the front row under lower impinging reynolds number or bigger jet - to - surface spacing
對于單排垂直射流，沖擊冷卻效果隨射流雷諾數的增加、孔間距與直徑比的減小而得到提高，沖擊間距比為2時換熱效果最好;沖擊孔中心線向通道封閉一側傾斜后，射流沖擊冷卻的范圍變窄，當沖擊間距比大於2時駐點區的對流換熱能力明顯降低;對于雙排沖擊射流，孔排間距與直徑比的增加使沖擊冷卻范圍變大，但在兩排孔之間區域的對流換熱系數有所下降;在較小的沖擊射流雷諾數和較大的沖擊間距比下，後排射流的沖擊換熱效果要遜於前排射流。 -
A new wavelet - bispectrum united detection algorithm is proposed to face with problems such as the complex structure and low signal to noise ratio of radar echo, when there exist difficulties in detecting impulses in through - wall radar systems
摘要針對沖擊體制穿墻雷達系統中回波信號結構復雜、信噪比低、信號檢測困難等問題，提出一種小波雙譜聯合檢測新演算法。 -
There was no difference in other biologic characteristic of mscs between the two separation method, such as cell anchorage ratio and clone formation ratio. ( 2 ) plga film presented uniformity frame with no protuberance and fissure under scanning electron microscopy ( sem ). big aperture with smooth wall and average 400 m i n size running - through each other was observed in porous plga substrate, around the big aperture there were many round micropores about 5 m size. all of the structure were equal and uniform, which satisfied the further research work. ( 3 ) mscs adhesion at earlier time was promoted by biotiegenrafter 3h, cell number was ( 1. 5 0. 18 ) 105 in the plga film coated with biotiegen group, which was significantly higher than that in plga film group ( p < 0. 01 ) and higher than that in coverslip group ( p < 0. 05 ), which cell number was ( 1. 04 0. 21 ) 105. after 6h and 12h biotiegen could not promote cell adhesion, and cell proliferation and alkaline phosphatase ( alp ) activity were not promoted dramatically during 9 days. ( 4 ) cell adhesion was promoted by fibronectin or collagen type i
G ） i型膠原、纖維粘連蛋白促進細胞增殖，細胞接種后3 、 6 、 gd三個檢測時間點，實驗組細胞均明顯高於對照組。與1型膠原相比，纖維粘連蛋白刺激作用更強。 ） i型膠原、纖維粘連蛋白尚能誘導mscs細胞向成骨細胞分化，不僅表達成骨細胞標志物ocn 、 alp 、 opnmrna ，而且堿性磷酸酶活性明顯增高，堿性磷酸酶及鈣結節7第四軍醫大學博士學位論文一染色均強陽性， i型膠原組mscs細胞堿性磷酸酶活性較fn組更高，有顯著性差異；同時，兔疫組化染色表明，經纖維粘連蛋白作用的mscs1型膠原表達陽性。 -
Abstract : a new waveguide which can change the wide wall of a rectangular waveguide into a symmetric arc wall is named as a cam - rectangular waveguide. comparing to sectoral waveguide, the new waveguide has the same voltage characteristics and is easier to be produced and fixed. an approximate formula of the dominant mode fields and the normalized conductance of a longitudinal resonant slot cut in the curved wall of a cam - rectangular waveguide are given. a resonant slot linear array in c & x band is designed, in which the slot voltage distribution is equiphase and the input is matched. the input voltage stationary ware ratio and the h - plane pattern of the antenna are measured. the experimental results show the conformance with theoretical results
文摘:把常用的矩形波導一個寬面改成圓弧形構成的波導稱為圓突-矩形波導.這種波導與扇面波導相比：電性能相當；波導管結構更加簡單，容易加工，便於安裝.文中給出圓突-矩形波導中主模場，圓曲面上縱向槽歸一化諧振電導近似公式.設計了c和x波段波導曲面縱向諧振縫隙線陣，縫隙電壓相位為同相分佈，輸入端匹配.實際測量了天線輸入端電壓駐波比和h面方向圖，理論與實驗相吻合 -
B. for hard and half hard drawn tubes the ratio of outer diameter to wall thickness is no more than 25
硬態和半硬態拉制管外徑與壁厚之比不小於25者。 -
The result indicates that the range of stable lean operation varies greatly for different cavity depth d and length - depth - ratio l / d, it increases with increasing d and l / d, and increases, followed by decreasing with increasing incline angle of aft wall
研究發現:凹腔深度和長深比對凹腔火焰穩定器的貧油極限影響較大，貧油穩焰范圍與深度、長深比成正比，隨後壁傾斜角的增大先增大后減小。 -
Then the probably factors which affect the arch in the wall are analyzed through the linear program in which the ratio of the height to the span of the beam is the most
然後用線彈性程序對可能影響墻梁拱效應的各個因素進行了詳細的分析，得出托梁的高跨比是影響墻梁拱效應高度的最主要因素。 -
In particular, the concealed bracings have more evident effects in improving bearing and energy - dissipation capacity of the wall slabs in coupled shear walls with lintel beams of relative smaller span - height - ratio. 4
特別是在連梁跨高比相對小的雙肢墻墻肢中增加暗支撐對雙肢墻承載力、耗能提高的作用更為明顯。 -
The influences of different reinforcement style of the concealed bracings and different span - height ratio of lintel beams on bearing capacity, stiffness and deterioration process, ductility, hysteresity capacity, energy dissipation and failure features of coupled shear wall were studied through experiment of 7 specimens under low cyclic loading
通過7個結構試件在低周反復荷載作用下的試驗，研究了不同暗支撐配筋形式、不同連梁跨高比對雙肢剪力墻的承載力、剛度及其衰減過程、延性、滯回特性、耗能、破壞特徵等方面的影響。 -
Based on the review, the fluid flow and heat transfer in the curved circular and rectangular pipes have been researched by employing perturbation method and numerical simulation with a physical model under the rotational orthogonal curvilinear coordinate in a rotating curvilinear pipe with multi - parameters. we firstly analyzed the fully developed fluid flow and heat transfer, mixed convection heat transfer, the development of flow and heat transfer in the inlet in different cross section ( circular, elliptical, annular and rectangular crossection ). the variations of the secondary flow, axial velocity, distribution of temperature, the friction force on the wall, the ratio of friction factor as well as the nusselt number with different dimensionless parameters had been examined in detailed
本文在總結和分析了一個世紀以來有關曲線管道流動和換熱特性的研究成果的基礎上，以旋轉正交曲線坐標系統下的多參數旋轉螺旋管道中的對流傳熱為物理模型，通過攝動方法和有限體積法，首次對各種截面（圓截面、橢圓截面、環形截面、矩形截面）旋轉曲線管道內充分發展流動的流動結構和傳熱特性（包括耦合對流傳熱特性）以及旋轉曲線管道開口段發展流動的流動結構和換熱特性進行了系統的數值模擬和理論分析，詳細討論了各種無量綱參數對管道內軸向速度分佈、二次流結構、溫度分佈、壁面摩擦力、摩擦系數比以及管道nusselt數的影響，獲得了若干創新性成果。 -
Determinaton of cotton maturity coefficient by lumen width - cell wall thickness ratio method
中腔胞壁比值法測定棉纖維成熟度系數的討論 -
The capillary vessel number in every unit area increased and the microvascular wall incrassated gradually with aging. the number ratio between capillary vessels and seminiferous tubules were on the trend of increase from 3 weeks to 3 months and decrease from 3 months to 12 months
隨著增齡，單位面積內微血管數目逐漸增多；管壁也明顯增厚；微血管數與生精小管數的比值從初生後到3月齡逐漸增大，從3月齡到24月齡呈減小的趨勢。 -
The adding of process - control agent can effectively keep the powder from sticking to the milling ball and the inner wall of containers. the increase of rotating velocity and the ratio of ball to powder can accelerate the phase transformation and thus shorten the alloying time
加入過程式控制制劑，可以有效地防止粉末粘覆磨球和罐內壁；球磨轉速的提高和球粉比的增加，都會加速相轉變過程，從而縮短合金化時間。
分享友人