waste steam boiler 中文意思是什麼

waste steam boiler 解釋
廢汽鍋爐
  • waste : adj 1 荒蕪的，不毛的，荒廢了的；未開墾的；荒涼的。2 廢棄的，無用的；多餘的；身體內排泄的。vt 1 糟...
  • steam : n 1 蒸汽，水蒸氣，水氣，霧，蒸氣壓力。2 〈口語〉精神，精力，氣力；怒氣。3 輪船，乘輪船旅行。vi 1 ...
  • boiler : n. 1. 煮器（壺、鍋等）；熬煮東西的人。2. 汽鍋，鍋爐；〈美俚〉酒類干餾器。3. 〈俚語〉導彈。
  1. The influence concerning calorific value of municipal solid waste ( msw ) fuel upon the boiler efficiency, and the problem of steam turbine ' s suitability for variabe operation condition have been analysed by using practical calculation example

    摘要針對垃圾燃料熱值對鍋爐效率的影響及汽輪機的變工況適應性等問題，結合實際算例進行了分析。
  2. The three - wastes fluid - bed multifuel burner utilizes the characteristics of fluid - bed burning and the blow gas waste heat boiler for recovery, and burns the waste gas, ash and residue from the gasifier to produce hot flue gas, which, after dust settling in the multiple dust collector, enters the waste heat boiler to recover waste heat for the generation of high - grade steam to be used in production

    摘要三廢流化床混燃爐系運用流化床燃燒特點，採用吹風氣餘熱鍋爐回收模式，對造氣產生的廢渣、廢灰、廢氣混燃，產生熱煙氣，經組合式除塵器除塵后，進入餘熱鍋爐回收餘熱，生產高品質蒸汽供生產用。
  3. Further, waste heat recovery boiler and steam turbine are combined to improve system efficiency, resulting combined cycle generation. main characteristics of this technology are as follows

    為進一步提高系統效率，可利用氣化系統和內燃機產生的余熱，通過余熱鍋爐和蒸汽輪機實現聯合循環發電。
  4. This essay has touched upon the following work : 1. has built up theoretic models including static mathematic models of air compressor, combustion chamber, gas turbine, waste heat recovery boiler and steam turbine which are deduced according to the feature and theory of the equipment of the object of study. upon establishment of each model based on the actual conditions, a method of multiple imitation and combination is applied to parts which have already got characteristic curves to have achieved quite accurate curves whilst the method of neural net is applied to the parts which have no characteristic curves for establishment of models

    本文進行了以下的主要工作：建立理論模型，根據對象的實際設備的特點和理論關系推導壓氣機、燃燒室、燃氣輪機、余熱鍋爐、汽輪機的靜態數學模型；根據本研究的實際情況，在建立各部件模型時，對已有特性曲線的部件，採用多項式擬合的方法，得到較為準確的特性，而對部分沒有曲線的特性，則採用神經網路的方法建立模型。
分享友人
分享到 Line

分享到臉書