wear curve 中文意思是什麼
wear curve
解釋
磨損曲線-
The fourth chapter introduces the theory of fractional brown movement ( fbm ). the image texture of turning workpiece is analyzed using fbm model. after abstracting the texture character, the cutting tool wear status can be determined according to fractal dimension and average slope of the fitting curve of the logarithm power spectrum
第四章採用分數布朗運動（ fbm ）的基本理論，對切削工件表面紋理的圖像進行分析，提取紋理特徵參數，根據分形維數和圖像上對數功率譜的擬合曲線的平均斜率來判斷刀具的磨損狀態。 -
The main contents of the experiments includes such items as follows : design of the new wear - resisting cast steel ' s chemical composition, determination and analysis of the new wear - resisting steel ' s quench degree and cct curve, ananysis of the cast structure, study of t he new wear - resisting steel ' s heat treatment process
在此基礎上，對chme鋼的淬透性，熱處理工藝、耐磨性進行了試驗研究，並制定了熔煉、鑄造、熱處理工藝，進行了生產小試和裝機試運行。試驗結果表明，設計的chme鋼淬透性良好，能滿足大型球磨機襯板的淬透性要求。 -
This article introduces the fundamental theory and the characteristics of the radial truck, points out the distinct advantages in high adherance, curve negotiating, low wear and low noise
與傳統的旋轉電機轉向架相比，具有非摩擦高粘著、小半徑曲線、低磨耗、低噪聲、小型化等優點，適合現代化城市快速小曲線、陡坡道、立體化軌道交通的需要。 -
The image of the curve is obtained by planar ccd system. the author independently works on : ( 1 ) the image processing : ( 2 ) the imaging model of the ccd cameras, that is the coordinate transforming relationship between the image coordinates and the corresponding world coordinates : ( 3 ) the method of curve connection : ( 4 ) the experiments of the figures of the wheel trackside profile and calculation of the flange thickness related to the wheel wear
作者獨立完成的工作包括： （ 1 ）對車輪輪廓的激光曲線圖象進行處理； （ 2 ）建立了左、右ccd攝像機的實際攝像模型，推導出圖象坐標到物方實際坐標的變換關系； （ 3 ）研究了幾種曲線拼接方法； （ 4 ）通過實驗，應用曲線拼接方法確定輪廓曲線的形狀，最終算出反映車輪磨損的重要參數。 -
There will appear a very uneven flow field, and appear a very big velocity magnitude distribution and ash concentration distribution near back wall. thus, the velocity magnitude is far bigger than that of optimal design velocity magnitude, which will lead to serious wear and tear in metal face of heater. especially, because of curve structure in front of heat pipe air preheater, there is more serious wear and tear
由於靠近豎井后墻面的煙氣流速很大，飛灰濃度也較大，斷面速度分佈的最大速度大於最佳設計速度的2 - 3倍，這樣將造成受熱面的嚴重磨損，特別是熱管空氣預熱器前端煙道的幾何結構有一定的轉角，更增加了磨損的程度。 -
The meeting when some people move feels bust bodice is an encumbrance, because this does not wear bust bodice, make so easily bosom curve go out of form
有些人運動時會感到胸罩是個累贅，因此不戴胸罩，這樣輕易使胸部曲線走樣。
分享友人