wear tester 中文意思是什麼

wear tester 解釋
地毯耐磨試驗機
  • wear : vt （wore ； worn ）1 穿著，戴著，掛著，佩著，帶著。2 留著（胡須等）；有著（記憶等）。3 帶著（某...
  • tester : n. 1. 試驗者，檢驗者，化驗者。2. 檢驗器，化驗裝置。3. （試驗用的）對照物。n. （床，佈道壇等上的）天蓋，華蓋。n. （一面有頭像的）古銀幣；〈古、謔〉六辨士。
  1. The friction and wear properties of pa6 composites filled with different contents of nano - al2o3 sliding against 45 steel and cu counterface in dry conditions are evaluated by using an mmw - 1 friction and wear tester. the findings show that incorporation of nano - al2o3 into pa6 serves as physical joints with the molecular chain of pa6 matrix, and helps reduce wear mass loss of pa6

    對于銅摩擦副而言，尼龍6 nano - al _ 2o _ 3復合材料的摩擦系數在載荷一定時，隨納米al _ 2o _ 3填料粒子填充量的增加摩擦系數呈上升趨勢，此變化規律對于復合材料與45 ~ #鋼對摩時則不明顯。
  2. Gas permeability tester and mechanical folding device were developed to study the barrier property and deformation failure behaviors. the surface characterization, chemical structure, optical, mechanical properties of pet coated with dlc have been investigated by x - ray photoelectron spectroscopy ( xps ), contact angle measurement, light transmission analysis, nanoindentation and friction wear tests

    通過x射線光電子譜分析、接觸角測定、光學透過率分析、納米壓痕、摩擦磨損試驗、機械彎折試驗、氣體透過率試驗，對膜層的表面特徵，光學、力學及氣體阻隔性能進行了系統的研究。
  3. The erosive wear behaviors of five engineering materials, include a3 steel, 1crl8ni9ti stainless steel, high chromium cast iron, ptfe and corundum, were studied by an air blast tester under ambient

    採用氣流噴砂型實驗裝置測試了a _ 3鋼、 1cr18ni9ti不銹鋼、高鉻鑄鐵、聚四氟乙烯和剛玉五種工程材料的耐沖蝕性能。
  4. From the viewpoint of the characteristics of two - phase liquid sand slurry wear, combined with the examination and study on easily damaged workpieces, the wear failure ' s basic rules are pointed out, of the pump shell and the cutter - piece on service, and the general principles of material wear - resistant designs put forward. the sand slurry abrasion tester has been designed and developed which can simulate general dredging conditions. summarized and presented are the position - exchange measuring method of sand slurry abrasion test and the experiment specification of sand slurry wear test of dredging conditions

    文中系統論述了作者在疏浚工況泥沙磨損機理及其耐磨新材料課題研究中的工作成果，主要研究內容和創新點如下：總結分析了磨損研究動態和提高材料耐磨性的方法；從兩相流泥沙磨損的特點出發，結合對失效易損件的考察研究，分析指出了現役泥泵殼和絞刀片磨損失效的基本規律，提出了材料耐磨損設計的基本思想；設計研製了能模擬疏浚工況的泥沙磨損試驗機，總結提出了泥沙磨損試驗換位測試法和疏浚工況泥沙磨損試驗規范。
  5. Based on an experiment performed on the piston ring - cylinder bore wear tester, liquid - solid lubrication is investigated in this thesis. the wear of the samples under different lubrication conditions ( the solid concentrations are 0 %, 0. 02 % and 0. 1 % by weight ) are discussed. the variations of the surface topography, especially the statistical parameters and functional parameters are studied, and the reasons that cause the variations are analysed

    本研究基於活塞環-缸套摩擦磨損臺架實驗研究了液-固二相流體潤滑的問題，探討了潤滑油中不含固體顆粒、含有0 . 02和0 . 1納米顆粒三種潤滑狀態下的磨損情況，並進一步研究了液-固二相流體潤滑狀態下試件表面形貌特性的變化，主要是統計參數和功能參數的變化，並探討了引起變化的原因，為更深入的液-固二相流體潤滑問題的研究以及表面形貌設計提供理論上的參考。
  6. Load - wear index an index of the ability of a lubricant to prevent wear under applied loads as determined in the four - ball ep tester

    負荷-磨損指數是衡量潤滑油在四球極壓試驗中所施加的負荷下所表現出的抗磨能力的一項指數。
  7. The signal processing software was developed by vc + + tools. the modules of the software including board controlling, signal input, data saving, figure display, statistic computing, filter design, spectrum analysis, etc. based on the experiment performed on the piston ring - cylinder bore wear tester, the friction force and max scuffing load under different liquid - solid lubrication ( the solid concentrations are 0 %, 0. 02 % and 0. 1 % by weight, the type of particles are mos2 and udp ) is investigated in this thesis

    然後，以內燃機中的活塞環-缸套摩擦副為目標，在活塞環-缸套摩擦副實驗臺架上進行模擬實驗，考察在不同二相流潤滑（潤滑油分別為純潤滑油、含納米級金剛石粉（ udp ） 、二硫化鉬粉（ mos _ 2 ）的濃度為0 . 02和0 . 1的液-固二相潤滑油）條件下摩擦副的摩擦力及極限擦傷載荷的變化。
  8. The dry sliding wear properties of ptfe composites filled with surface treated and untreated nano - alaoa were tested on the model mm - 200 tester, the effects of filled nano - abos content >

    利用mm - 200型磨損試驗機考察了納米al _ 2o _ 3含量、載荷和對摩時間對表面處理納米al _ 2o _ 3填充ptfe復合材料在干摩擦滑動條件下摩擦磨損性能的影響。
  9. Testing of lubricants ; testing by the shell four - ball tester ; determination of wear characteristics for consistent lubricants

    潤滑劑檢驗.用殼牌公司的四球試驗儀檢驗.潤滑脂磨損
  10. Plain bearings - testing of friction and wear of precision engineering bearings in the slpg - tester

    滑動軸承. slpg試驗機精密工程軸承的摩擦和磨損測試
分享友人
分享到 Line

分享到臉書