wear testing 中文意思是什麼
wear testing
解釋
耐磨試驗-
Testing the wear and effectiveness of metallic abrasives by centrifugal blasting
用離心噴砂法試驗金屬磨料的磨損情況和效果 -
The physical properties of the knitted fabric made of soybean protein composite fiber and cotton are tested, wear comparison testing on knitted underwear is made, and the wear comfortability of the two kinds of fabric is evaluated
摘要測試了大豆蛋白復合纖維針織物與棉針織物物理性能，同時對其針織內衣進行了穿著對比實驗，並主觀評價了兩種面料的穿著舒適性能。 -
Implants for surgery - wear of total knee - joint prostheses - loading and displacement parameters for wear - testing machines with displacement control and corresponding environmental conditions for test
外科植入物.全部膝關節假肢的磨損.帶位移控制和相關試驗環境條件的磨損試驗機械的負載和位移參數 -
Implants for surgery - wear of total knee - joint prostheses - part 1 : loading and displacement parameters for wear - testing machines with load control and corresponding environmental conditions for test
外科植入物.全膝關節假體的磨損.第1部分:試驗用有負荷控制和相應環境條件的磨損試驗機的負荷和位移參數 -
The characteristics and shortcomings of high temperature sliding wear testing machine for roll materials in china and a broad were analyzed in this paper
摘要文章分析了國內外軋輥材料高溫摩擦磨損試驗機的特點及其存在的不足，在此基礎上，研製開發了一臺材料高溫滑動磨損與熱接觸疲勞試驗機，並進行了初步的實驗。 -
Standard test method for durability wear testing of separable electrical connector systems using electrical resistance measurements
可拆卸電插接件耐耗試驗的電阻測量標準試驗方法 -
Then we can estimate the lubrication state between the friction faces. with the old large numbers of testing numbers the wear parameter k of every point on the steady work ' s cam can be decided
通過計算凸輪表面各位置潤滑油膜厚度，判斷其潤滑狀態，結合以前大量的實驗數據，確定出凸輪各位置在穩態下工作時的磨損系數k值。 -
05. 02 calibration and operation of the alpha model lfw - 1 friction and wear testing machine, method for
型lfw - 1摩擦和磨損試驗機的校準和操作方法 -
Standard test method for calibration and operation of the falex block - on - ring friction and wear testing machine
法列克司環塊磨擦試驗機和磨損試驗機的校準和操作標準試驗方法 -
Implants for surgery - wear of total hip joint prostheses - loading and displacement parameters for wear - testing machines and corresponding environmental conditions for test
外科植入物.全部髖關節假肢的磨損.磨損的負荷和位移參數.磨損試驗機和相應環境條件 -
Implants for surgery - wear of total hip - joint prostheses - part 1 : loading and displacement parameters for wear - testing machines and corresponding environmental conditions for test
外科植入物.全髖關節假體的磨損.第1部分:試驗用磨損試驗機和相應環境條件的負荷和位移參數 -
Implants for surgery - wear of total knee joint prostheses - loading and displacement parameters for wear - testing machines with load control and corresponding environmental conditions for test
外科植入物.全部膝關節假肢的磨損.磨損試驗機的負荷和位移參數.帶有負荷控制和相應控制條件的試驗機 -
The friction and wear behavior of dlc gradient film on tj6a14v alloy substrate sliding against ultra - high molecular weight polyethylene was investigated by comparing with that of ti6a14v alloy against the same counterpart under the same testing conditions
研究了dlc梯度薄膜材料與uhmwpe組成的摩擦副的生物摩擦學性能，探討了摩擦磨損機理。 ti6a14v基dlc梯度薄膜材料具有較好的減摩特性和耐磨損特性。 -
3. the diamond segment wear process was analyzed by testing the weight of segment before and after sawing. the patterns of wear and breakage of diamond grits and bond wear mechanism of the blade were analyzed based on the observation on the working surface of the saw blade by stereo microscope and scanning electronic microscope
採用稱重法測量鋸切過程鋸片節塊磨損量，並通過計算磨削比，分析了混凝土鋸切過程金剛石節塊的磨損特性及其影響因素，並採用sem和體視顯微鏡觀察節塊不同部位工作表面和金剛石的磨損破壞情況，研究了金剛石磨損破壞的主要形式和胎體材料的磨損形態。 -
Standard test method for wear rate and coefficient of friction of materials in self - lubricated rubbing contact using a thrust washer testing machine
用止推墊圈試驗機測定自潤滑磨擦接觸中材料磨損速率和摩擦系數的標準試驗方法 -
05. 02 wear rate of materials in unlubricated rubbing contact using a thrust washer testing machine, test for
用止推墊圈試驗機測定在非潤滑摩擦接觸中材料的磨損率的試驗 -
The wear mechanism of tungsten carbide particle reinforced steel matrix composites was studied according to the frictional and wear characteristics and the scanning electron microscopy photographs of worn surfaces after wear testing. the effect of heat treatment and tungsten carbide content on wear resistance was investigated as well
結合磨損特性曲線和不同磨損時間的摩擦面sem照片，分析了wc鋼復合材料的磨損機理，並討論了不同熱處理工藝和wc顆粒含量對wc鋼復合材料磨損性能的影響。 -
Standard test method for wear testing with a pin - on - disk apparatus
用針盤儀進行磨損檢測的標準試驗方法 -
Standard test methods for wear testing rotary operators for windows
窗磨損試驗旋轉操作器的標準試驗方法 -
By adopting the sliding wear testing method, the wear behavior of no 45 steel testing pieces with different diameters and distribution densities of pits treated by laser were studied under temperatures of 200 and 400
摘要採用滑動磨損試驗方法研究在200 、 400溫度下，經激光處理后不同凹坑尺寸和分佈密度的45鋼試件的磨損性能。
分享友人