wedge effect 中文意思是什麼
wedge effect
解釋
楔效應-
With account for the effect of temperature and shock - boundary layer interaction, the forebody / inlet with plane lip and wedge lip are designed by using the design methods of constant shock wave intensity and constant shock wave angle. in the design, the incidence angle of the first ramp, height of isolator, length of forebody and total turning angle of the designed forebody / inlet models are given
另外，根據優選結果，給定前體長度、前體預壓縮楔角、總壓縮轉角及隔離段高度，分別用等激波強度和等激波角度的方法設計了唇口平直和唇口帶楔角的前體進氣道。 -
The characteristics of high pressure gyratory sprayed pumping discusses is presented, which is applicable in wide range of scope and ground layers, convenient for construction, long durability, wide source of materials. mechanism for subgrade strengthening : complex foundation of cement solid and earth between piles was formed by pulsant load of flowing pressure and spraying flow, water wallop, cavitation phenomenon, water wedge effect, extrusion force and air flow agitation etc so as to enhance foundation bearing force and reduce settlement and deformation
高壓旋噴注漿技術具有適用范圍、適用地層較廣，施工方便，耐久性好，材料廣闊等特點；其加固地基機理主要是通過流動壓、噴射流的脈動負荷、水塊的沖擊力、空穴現象、水楔效應、擠壓力、氣流攪動等效應形成水泥固結體與樁間土的復合地基，從而提高地基承載力，減少沉降變形。 -
Secondly, the effect of transverse deforming on the property of the wedge pressing was studied. the results showed that : the wedge pressing stock with the transverse deforming amount of 10 % acquired the best performance. the highest density got the biggest rate of slope while with the amount of 30 % the curve was more some special structure and performance as following : the large porosities was crushed into small or linear ones with the high - direction deformation amount of 20 % ; as the increasing of the high - direction deforming, the particles got a further deforming, the porosities got a further crushing, the small porosities were mergered by the large ones and the former then disappeared ; when the amound reached 60 %, the quantity of the porosities would obviously decrease which made the materials compact, the microstructure more uniform and the density and hardness curves more horizontal, the relative desity could reach 99. 7 %, the tensile strength b of the as - compacted samples reached 408mpa with the yield strength s teached 289mpa and the elongation percentage reached 13. 6 %. in addition, the microstructure of the wedge pressing stock under the pressing temperectureof 450 was uniform, the porosities and the boundries of the grains basically disappeared and the conjunction between particles was great
採用雙向楔形壓制，大尺寸噴射沉積5a06鋁合金楔壓坯的組織和性能變化具有如下特點:當高向變形量為20 %時，大的孔洞變形破碎為小的孔洞，或呈線狀孔;隨著高向變形量的增加，顆粒進一步變形，孔洞進一步破碎，大孔「吞併」小孔，小孔塌陷並逐步消失;當高向變形量達到60 %時，孔洞量大為減少，材料基本緻密，組織趨于均勻，楔壓坯料的密度、硬度變化曲線接近水平線，坯料的相對密度達99 . 7 % ，抗拉強度_ b = 408mpa ，屈服強度_ （ 0 . 2 ） = 289mpa ，延伸率= 13 . 6 % ;對比其它的壓制溫度，在450楔形壓制的坯料組織均勻，孔洞及顆粒邊界基本消失，顆粒之間冶金結合良好。 -
Wherefore, other two energy - based fracture parameters are put forward : the stable fracture energy gfs, indicating the average energy dissipation during the crack stable propagation and the unstable fracture energy gfu, corresponding to the crack unstable fracture stage. wedge. ? splitting specimens are tested with a view to understanding those two parameters " size effect in terms of the initial crack length a0
本文提出兩個能量型斷裂參數即穩定斷裂能g _ （ fs ）和失穩斷裂能g _ （ fu ）分別表示裂縫穩定擴展和失穩擴展階段的能量損耗，並採用楔入劈拉試件（ ws ）對這兩個參數相對初始縫長_ 0的尺寸效應進行了分析。
分享友人