winding number 中文意思是什麼
winding number
解釋
繞數-
Analysis for magnetic field of srm is very complicated since the flux waveforms in different parts of the motor vary with motor phase, stator pole and rotor number, also with the winding connections, etc, which results in the srm losses, especially iron loss calculation difficult. the temperature analysis due to the losses has become a study hot spot
Sr電機鐵心的磁通波形不僅與電機的相數有關，還與定、轉子齒極數、定子繞組連接方式等密切相關，從而使得sr電機磁場分析很復雜，復雜的磁通密度波形導致電機損耗特別是鐵損的計算非常困難。電機的損耗又會引起電機的溫升，因此高性能的sr電機的熱分析也成為目前的研究熱點。 -
Product disqualification rate caused by machine itself shall be no more than1 （ phenomenon of disqualification are as follows : incorrect winding circle number 、 inter - circle short circuit 、 wire fail to embed into the slot ， enameled wire not hitched the commutator ' s hook ， or thrum and wire ends loosens after being pulled ）
因機器本身導致的產品不合格率1 （不合格現象為繞線匝數不準、匝間短路、線未嵌入槽內，漆包線未掛入換向器掛鉤上，線頭或線尾拉斷后松脫） 。 -
4. to get the motor ' s performance by calculation with known formulas, as a result an adjustment for the motor ' s configuration can be practised. when a combined method of altering the length of armature, the number of turns in the winding and the dimension of permanent magnet is used. 5. to get the motor ' s performance when it is driven by the power converter. finally, the calculated data are compared with the experimental measurements, so as to verify the rationality and reliability of the method
Q採用數值分析直軸負載磁場和交軸電樞反應磁場的方法來計算，得到較為準確的結果；根據電機工作特性的計算公式計算電機性能，由計算結果調整電機的結構，而調整工作使用改變電機鐵心長度、繞組匝數和永磁體尺寸相結合的方法，這樣可以得到較為理想的結果；對變頻電源供電時電機的工作特性進行計算，以檢驗其變頻時的性能。 -
Firstly, considering the molecular pump is small and the elimination of heat condition is bad, this paper presents the structure of the mb, including the material of the rotor and stator, the number of magnetic poles, the stator slot shape of mb, the layout of the magnetic poles, the coins winding and so on
首先綜合考慮了分子泵體積小、磁軸承散熱條件不好的特點，設計了分子泵磁懸浮軸承的結構，選擇了軸承鐵芯的材料，設計了磁極的布置、槽的形狀、磁極數目和線圈纏繞方式。 -
First, the complete machine is controlled by the germany siemens programmable local controller ( plc ). secondly, mitsubishi e - 540 variable frequency main shaft stepless speed regulation function is provided. thirdly, siemens chinese td - 200 text panel indicator is used for parameter set. the winding number, tension and velocity can be modifies at real time. in addition, the complete machine has high degree of automation. the work of filling in workpiece, clamping, moving workpiece to the winding position, winding, trimming and holding line head etc can be finished for one time
參數設定採用西門子中文td - 200文本面板顯示器，可對匝數繞線張力、繞線速度參數進行實時修改。整機自動化程度高。從工件放入工件夾緊送工件至繞線位繞線剪線並夾住線頭… …一次性完成。 -
This numerical simulation is not limited by number of cooler, winding at each pole, directed area, and horizontal duct in each directed area, and not limited by geometrical size of discs and ducts
數值模擬對變壓器所配冷卻器臺數、每柱線圈數、各線圈導向區間數、每區內水平油道數以及線餅、油道的幾何尺寸沒有特別的限制。
分享友人