working conditions temperature 中文意思是什麼

working conditions temperature 解釋
工作環境溫度
  • working : adj 1 工作的，從事勞動的。2 操作的，作業的。3 工人的。4 （用於）實際工作的，任事的；使用（中）的...
  • conditions : （旅遊合同中）條件或服務項目
  • temperature : n. 1. 溫度，氣溫。2. 體溫。3. 〈口語〉發燒，高燒。
  1. This article aims at the boiler ' s problems in operation : 1 ) under nominal load, the smoke temperature at the outlet of hearth reaches 1200, far more exceeds 1050 the original designed temperature. this will always result in slag inside boiler and the temperature of overheater ' s pipe superheat, so that boiler cannot take nominal load and all these influence boiler ' s nomal operation heavily, 2 ) this article also studied the reason why the assistant oil becoming necessary when coal changes. during the nomal operation, many factors ( makeup of combustor and its disposal, smirch and encrust of water wall, excessive air coefficient, temperature of primary air, coal type and density of coal dust ) can deviate the designed working conditions, then affect the boiler ' s nomal operation

    本文針對該鍋爐在實際運行中存在的問題：在額定負荷下，爐膛出口超溫、低溫段過熱器前煙溫高達936 ，遠遠超過815的設計值；噴燃器四周水冷壁結焦嚴重，過熱器管壁溫度超標，無法帶上額定負荷；甚至有時因燃煤質量的變化，必須投油助燃的嚴重情況進行了分析研究。在實際生產過程中，燃燒器的結構、布置，水冷壁的粘污、結垢，過剩空氣系數、一次風溫、煤種及其濃度變化等許多因素都會偏離鍋爐的設計工況，從而影響爐內的傳熱和燃燒，造成爐膛出口超溫、水冷壁結渣等問題。
  2. Borrowing ideas from design theory and structure type of oil hydraulic proportional throttle valve and taking domestic and overseas correlative development as reference, this paper determines working conditions of the valve, designs its structure, selects suitable materials of its components, and performs corresponding intensity and temperature check

    在借鑒油壓比例節流閥的設計理論、結構型式以及參考國內外相關研究成果的基礎上，確定了水壓比例節流閥的工作條件，設計了水壓比例節流閥的結構型式，選取了合適的元件材料，並進行了相應的強度和溫升校核。
  3. They will short down the working life of air compressor because they are always started or stopped when we want to make the railway carriage stay in a fixed temperature. now, automatic and intelligent control systems are being applying in bus air - conditions control. in this way, computers control the work of air compressor, the turnaround speed of fan, the open degrees of wind controlled doors and so on

    我國大多數客車空調仍然採用簡單的壓縮機開關控制及循環離合控制系統，如：離合器?熱力膨脹閥系統（ cctxv ）和離合器?節流管系統（ ccot ） ，這些控制方式的精度低，當進行恆溫控制時壓縮機處于頻繁的開、停狀態，縮短了壓縮機的工作壽命。
  4. Abstract : based on the operation data, the cold start - up and warm start - up curves of a czecho 200 mw steam turbine are worked out according to the operation rules ; the fem calculating models of the temperature field and stress field of the high pressure rotor are established, and the suitable boundary conditions are given ; the temperature field and stress field of the high pressure rotor are calculated and analysized during these two working situation

    文摘:在現場實測數據的基礎上，根據運行規程擬定捷制200mw機組的冷態啟動和溫態啟動曲線；建立高壓轉子溫度場和應力場有限元計算模型，確定相應的邊界條件；計算分析在這兩種工況下高壓轉子的溫度場和熱應力場。
  5. On the basis of the analysis of fundamental principle of thermoelectric refrigeration, the steady state mathematical model of the thermoelectric system was founded. according to the model, the theoretical analysis and calculation are made on various working conditions, and analyzed theoretically the effects on thermoelectric system which caused by hot and cold temperature difference, the device ’ s effective system figure of merit, the properties of the heat changers, which established theoretical basic for the opening up and design of the thermoelectric system and its performance test

    在分析熱電製冷基本原理的基礎上，建立了熱電裝置的穩態系統數學模型，並依據該模型對熱電裝置系統進行了不同的工作狀態下的熱力分析計算，並就熱電裝置的冷熱端溫差、電堆片的優值系數、散熱器的散熱性能與熱電熱泵裝置性能的影響進行了理論分析，為熱電裝置的開發設計和現有熱電裝置的性能測試建立計算理論基礎。
  6. There was a stiff breeze blowing at game time. the temperature was in the low 40s, and a steady drizzle made for some uncomfortable working and viewing conditions

    球賽進行時冷鋒颼颼的吹。溫度約華氏40度，持續的毛毛雨讓投球與視線狀況不佳令人不舒服。
  7. Specially designed for the cylinder of the carding machine, fsm model motor is suitable for big rotating inertia and long staring time under the working conditions of plentiful dust, short fibers, high temperature and high humidity

    本型電動機專為梳棉機錫林（大滾筒）配套設計，主要適用於轉動慣大、起動時間要求長、多塵埃、短纖維、溫濕度較高的條件下工作。
  8. The working condition of nylon shaft liner is determined by many factors, for example : the different formula, shaping technique, the design of shaft liner, installation method, loading features, running speed, lubricant condition, the working environment of shaft liner temperature, humidity and the influence of impurity, abrasion when working etc. so, when designing shaft liner, it is necessary to take consideration of all conditions

    鑄型尼軸套的許用工作情況是由很多因素決定的，例如不同配方和成型工藝所制得的材料物理機械性能，軸套的設計裝配方法，負載特點，運轉速度，潤滑情況，軸套的工作環境溫度濕度雜質的影響，工作時的摩擦條件，對磨材料的性能等。因此，在設計軸套時，應綜合考慮各個方面的因素。
  9. We primarily do theses works : first, for the rtcvd equipment that we required has a big chamber, high working temperature and fast temperature ramp rate, the energy that required for the high temperature working conditions was computed ; then the reflector material and the shape of the reflector were chosen. through computer simulation we designed a reflector that can reflect the energy of each lamp individually through each half - cylindrical - face

    針對本課題要求的rtcvd設備的反應腔大、工作溫度高和升溫速度快的特點，首先對設備升溫條件進行能量計算；接著從反射腔材料選擇和形狀設計等方面出發，利用計算機模擬最終設計出為每根燈管分別反射輻射能的圓柱面形反射罩。
  10. The relationship between sputtering conditions and the depositional speed shows : with working pressure 1. 2 pa, sputtering power 180w, the depositional speed of tio2 thin film is 40nm / h, and increases with the increasing of sputtering power. it can be also founded that the depositional speed is nearly proportional to the working pressure : within the range of 0. 3pa to 1. 6pa, the depositional speed increases linearly with the increase of ar pressure. with the enhancement of the substrate ' s temperature of sputtering or annealing, the resulted thin films show a tendency of decreasing in thickness, and increasing in refractivity

    本實驗是採用磁控濺射方法，在不同的溫度下制備了tio _ 2薄膜，並對薄膜進行了不同溫度和時間的退火處理，通過原子力顯微鏡（ afm ） 、 x射線衍射（ xrd ） 、掃描電鏡（ sem ）等檢測手段對薄膜的表面形貌和組成結構進行了分析，結果如下： （ 1 ）濺射工藝條件與薄膜沉積速度的關系表明：採用1 . 2pa工作氣壓， 180w的射頻功率tio _ 2薄膜的沉積速率為40nm h ，並隨射頻功率的增加而提高，呈近似的線性關系，在0 . 3pa 1 . 6pa氣壓范圍中，氬氣壓強升高沉積速率迅速增加，濺射溫度提高和退火處理能使薄膜的厚度減小和折射率提高。
  11. The project based on the present level of technology to control exhaust of car, and the shortage application for cool egr in our country, aimed to research a kind of cool egr system which could adjust egr temperature automatically according to different working conditions of internal combustion engine. so the intelligent cool egr would be realized to decrease nox from car, which can satisfy the roul of low emission in our country

    本課題基於我國當前汽車排放技術相對落後的現狀，針對我國現階段汽車發動機冷卻廢氣再循環（ egr ）應用較少的問題，研製開發出一種能根據發動機不同工況調節egr冷卻溫度的外部冷卻egr系統，以實現冷卻egr的智能控制和精確控制，減少汽車尾氣中nox的含量，滿足國家的排放法規，減少汽車尾對環境的污染。
  12. Designed for long time working in severe conditions, such as high temperature, humidity and dustiness

    能在高溫、潮濕、多塵等惡劣條件下長時間工作；
  13. Corundum mullite product adoprs electrocast refractories. through high pressure formation and high temperature burning, this product has comparatively high refractoriness, mechanical strength and slftening temperature under load. it can be widely used as inner lining. of various industrial furnace under such hard working conditions as high temperature, flushing and erosion

    剛玉莫來石製品是採用電熔合成原料，高壓成型，高溫燒成的具有較高耐火度及機械強度，較高荷重軟化濁的可廣泛應用於各類工業爐高溫、沖刷、侵蝕條件較苛刻的窯爐內襯的耐火製品。
  14. 150 psig ( 10. 3 bar ) max. working pressure. 150 f ( 65 c ) max. working temperature. applications outside of these conditions require special design considerations

    最大工作壓力。 65 c最大工作溫度。在這些環境以外應用需要特殊的結構設計。
  15. Uses aluminum foil as the heating transfer carrier, clings electrifying heating linear component or other shape components to aluminum foil and consequently makes into electric heating groupware. usually the needed temperature is obtained by controlling power density, insulating materials and working heat dispersion conditions etc

    用鋁箔作為傳熱的載體，將加熱線通過輔助粘合劑粘合在鋁箔上，組成的片狀加熱器，從結構上可分為雙層鋁箔粘貼型單層鋁箔熱熔型。
  16. With high mechanical indexes, jfo3 series motor is of enclosed, self - cooling type, suitable for textile machines of cotton, wool, linen and silk in the working conditions of plentiful dust, short fibers, high temperature and high humidity. its two - speed motor is purposely designed for the spinning machine

    本系列電動機為封閉自扇冷式，具有較高的力能指標，適用於棉、毛、麻、絲等紡織機械，適宜在多塵埃、短纖維、溫濕度較高的環境中工作，其雙速電動機主要為細紗機設計配套。
  17. It is also found that the concentrations of reactant, catalyst, the time and temperature of action and the working conditions have perceptible effects on its membrane performances. in this paper, the application of these membranes is also introduced

    探討了原料濃度、交聯劑種類和濃度、催化劑、添加劑、反應時間和反應溫度對膜性能的影響，初步計算了聚乙烯醇/ 5102一a12o3復合納濾膜各膜層的阻力。
  18. Three - dimensional finite element model for the calculation of steady temperature field and thermal stress of the cws nozzle were established according to the structure of cws nozzle and its working conditions

    根據水煤漿噴嘴的結構和噴嘴工作情況，建立了水煤漿噴嘴三維穩態溫度場和熱應力的有限元模型，確定了邊界條件，分析求解得到陶瓷水煤漿噴嘴的溫度場、溫度梯度和熱應力。
  19. The engine is tested on the dynometer using the software that can monitor the ecu ( electronic control unit ) internal dataflow. and the electronic control fuel injection system parameters ( e. g. position of throttle valve, engine speed, air temperature, engine temperature, duration of injection ) are acquired at many different working conditions of engine

    本文以hirth3203二沖程汽油發動機為研究對象，利用開發的ecu內部動態數據流監測軟體進行發動機臺架試驗，獲取了在不同的油門開度和轉速下電控燃油噴射系統的一系列工作參數，如節氣門開度、發動機轉速、進氣溫度、氣缸溫度、蓄電池電壓以及噴油脈寬。
  20. No rise in temperature : the temperature will not increase as the materials are pulverized under the working conditions of pneumatic expansion and the temperature in the milling cavity is kept normal

    4不升溫，由於物料是在氣流膨脹狀態下粉碎，所以粉碎腔體溫度控制在常溫狀態，溫度不會升高。
分享友人
分享到 Line

分享到臉書