working fluid 中文意思是什麼
working fluid
解釋
泵浦工作液-
Function of acetic acid in acidizing working fluid
乙酸在酸化工作液中的作用 -
On the basis of the manufactured new aluminium heat pipe sets and research work done in the refrigeration lab of chongqing university, a new thermal syphon cooling machine made of aluminium has been designed. this text is to study this kind of thermal syphon to use working fluid methanol, ethanol and acetone
在重慶大學製冷實驗室已有研究工作及新型的鋁質cpu重力熱管散熱器基礎上，本文著重研究此種重力熱管使用天然工質甲醇、乙醇和丙酮時的工作特性。 -
But when the wind - speed becomes above 1m / s hereafter, wind - speed increase for the cpu thermal siphon of transmit heat the ability ' s gain result the deceleration. so it is considered perfect when the wind - speed is 1m / s. through this experimentation we found that when the cpu thermal syphon cooling machine used acetone as working fluid, wind - speed 1m / s, cpu chip caloricty 60w, its volumetric heat release rate came to 1. 3 104w / ( m3k )
通過本次實驗測出所使用的cpu重力熱管散熱器在使用丙酮為工質，風速1m / s ， cpu晶元發熱量為60w時，其體積散熱率達到1 . 3 104w / （ m3k ） ，能保證晶元溫度與環境溫度之差小於40 ，能很好的適應pentium -計算機長期運行的要求。 -
Using the opened thermosiphon of 38x3 as experimental element and water as working fluid, the characteristics of dynamic low load boiling, stable severe boiling heat transfer coefficient and critical heat flux are gotten for the opened thermosiphon at the pressure of 0. 02 - 0. 1mpa and 0. 1 - 0. 8mpa respectively, which makes up the drawback that the opened thermisiphon has not yet accurate boiling heat transfer relationship formulas. by means of experimental results, an opened thermisiphon waste heat recovery boiler is designed for the high temperature gases that the positi e electrode copper refining furnace exhaust, which overcomes effectively the drawback of short life, little capacity and unable to inspect that the closed steel - water thermosion has
本文以工程上常用的38 3的開口封底為實驗元件，以水為工質，對開啟式熱管內的動態低負荷沸騰、穩態旺盛沸騰及臨界沸騰特性進行系統的可視化實驗研究，實驗壓力為0 . 02 0 . 8mpa ，實驗得出了38 3的開口封底管在工作壓力為0 . 02 0 . 8mpa和0 . 1 0 . 8mpa下的管內沸騰傳熱系數及臨界熱負荷計算關聯式，彌補了開口封底管? ?這一新型傳熱元件尚無準確的沸騰換熱關聯式的缺陷。 -
The analysis indicates that in the absorbing refrigeration cycle using tfe - tegdme working fluid under the same evaporating temperature and condensation temperature, the performance of the simplicity cascade cycle is the best while the heat burden of the generator is the maximum, the performance of the mid - pressure double - effect cascade cycle is the worst while the heat burden of the generator is higher than the basic gax cycle
分析結果表明，採用以tfe - tegdme為工質吸收式製冷循環，在同樣的蒸發溫度和冷凝溫度下，單純復疊循環性能最為優越，但發生器的熱負荷也最大；中壓雙效循環性能最差，而且發生器的熱負荷要比基本gax循環大，運行的經濟性差。 -
Ceramic fuel cells are electrochemical devices that directly convert fuels such as gasified coal or natural gas into electricity without the limitation of the carnot cycle ( an ideal thermodynamic cycle in which heat is taken onto a working fluid at a constant upper temperature and rejected at a constant lower temperature )
陶瓷燃料電池是一種電氣化學裝置，能直接將煤氣、天然氣等燃料直接轉化為電能而不會受到卡諾循環（一種理想的熱力循環，熱量在恆定高溫下轉化成工作流體，在恆定低溫下被釋放）的限制。 -
With experiments and theoretical analyzing, we find when the heat discharge is smaller than the entrainment limited, what influences the ability of heat - transmitting of work quality is the quantity of injection and dry limit fluid inventory, the optimum quantity of injection of the three working fluid is 8 ~ 14g ; and the delivering factor that transmission coefficient is determined by capillary limit, not the heat transmission ability of the thermal syphon. therefore, among the three working fluid, acetone is the best. low wind - speed has the obvious function in heat transmission of the thermal syphon
本文通過實驗研究和理論分析，認為在熱流量小於攜帶極限時，影響工質傳熱能力的是cpu重力熱管的充液量和其乾涸極限，此次所實驗的三種工質，最佳充液量應當在8g ~ 14g ；傳輸因素主要決定普通熱管的毛細極限，而不是重力熱管傳熱能力的決定因素；三種工質中的最佳工質是丙酮；小風速時風速的變化對cpu重力熱管的傳熱有明顯的作用，但在風速大於1m / s以後，風速增加對于cpu重力熱管的傳熱能力的增加效果減緩。 -
From chapter 4 to chapter 7, the effects of the irreversibility of mass - transfer, the internal irreversibility inside a cyclic working fluid and mass leakage on the optimal performances of chemical cycle devices are investigated
第四章至第七章研究傳質不可逆性、工質內部不可逆性及質量漏對化學循環設備優化性能的影響。 -
Shanghai haiying chemical co., ltd is a new technology enterprise specialized in the production of metal working fluid. we have a strong technology power and high development and production capacity. our goal is to be a complex integrated the science research with production and sale
上海海營化工工貿實業公司是專業從事生產金屬加工液的新技術企業，公司技術力量雄厚，具有較強的開發和研製能力，公司的宗旨「集科研、生產、銷售服務於一體」 ，以質量第一、服務第一、為冶金、汽車、機電、軸承、造船等行業提供機械設備加工潤滑冷卻液。 -
The working parameters ( specific enthalpy, entropy, flux of working fluid, reynolds number, etc. ), the configuration parameters of the main components, such as steam turbine - generator group, evaporator and ehd condenser and system efficiency were calculated on the base of thermodynamics theory
文中以熱力學理論為基礎，計算了低溫余熱發電系統的運行參數（比焓、熵、工質流量、雷諾數、管路壓力等）和各主要組件如汽輪機-發電機組、蒸發器和ehd冷凝器的結構參數，並計算了系統的效率。 -
During operation of coal fueled power plant boiler, heat exchange surfaces will be polluted by soot accumulation. this seriously weakened the heat transfer capability from gas to working fluid
在電站燃煤鍋爐的運行過程中，受熱面必然會產生積灰污染，這就大大削弱了煙氣對工質的傳熱能力。 -
Simultaneously how to reduce the quantity consumed by the system of refrigerating is also a forward question for study in thermal - physical engineering. at the basis of analyzing thoroughly the stirling - cycle, the thesis puts forward a new refrigerating cycle in house - hold refrigerator, which adopts the two - state, two - component working fluid
本文在對stirling循環深入分析的基礎上，利用其定溫吸熱、放熱的優點，同時採用相變工質作為製冷劑，利用其在低溫下氣化吸熱製冷單位質量工質的製冷量大的特點，提出了採用雙相雙組份工作介質的新型家用冰箱的製冷循環。 -
Whereas, the research on torque characteristics, working fluid, two - phase flow in lvc has n ' t been mature by now. further study is undertaken based on former researches in this paper
但是目前對于液體粘性聯軸器的轉矩特性、工作流體特性以及硅油空氣的兩相流體流動與傳熱特性的研究，並不十分成熟。 -
This technology uses alkali metal ( such as lithium, potassium and sodium ) as the working fluid, base ( " - a1 _ ( 2 ) o _ ( 3 ) solid electrolyte ) as the medium. this technology is based on the unique properties of base that is an excellent ionic conductor but a poor electron conductor
Amtec利用堿金屬（鋰、鉀、鈉）作為工作物質， base （ - al _ 2o _ 3solidelectrolyte ）作為介質，這種陶瓷材料對離子是良導體，對電子幾乎是絕緣體，這一點也是這種能量轉換技術的基礎。 -
In chapter 2, a new irreversible cycle model is presented for an absorption refrigerator, in which not only the irreversibilities of heat conduction and heat leakage but also the irreversibilities resulting from the friction, eddy and other irreversible effects inside the working fluid are taken into account
第二章建立了不可逆吸收式製冷循環新模型，模型不僅考慮了熱傳導和熱漏不可逆性，而且也考慮了循環工質內部由於摩擦，渦流及其它不可逆效應所引起的內不可逆性。 -
This paper describes a hj 60 - y, y / 2. 5, 2. 5 - q type heat - pipe stove by beijing changxin lantian technology development co., ltd, which use an composite inorganic material as working fluid to heat oil and use natural gas as heat source. experiment is conducted to investigate heat - transfer performance of the special working fluid
本文的研究對象是北京長新藍天科技發展公司設計製造的hj60 - y ， y 2 . 5 ， 2 . 5 - q型熱管加熱爐，爐內採用一種復合高效無機傳熱材料作為傳熱介質，加熱源選用天然氣，被加熱的工質為原油。 -
Two heat - pipe with the same construction are produced by the special and common working fluid. during the experiment, the comparison of temperature distribution starting speed and transmit heat speed are tested, the effect of different heat length is observed at the same time. through compared and analyzed results of the test, its heat - transfer performance is known initially
本文首先對這種未知物性的特殊工質進行了實驗研究，把特殊工質和一種以知物性的普通工質製成兩根結構相同的熱管，在同樣條件下進行溫度分佈、啟動和傳熱速率等性能對比實驗，同時觀察了不同加熱段通過實驗結果的對比和分析，對這種特殊工質的傳熱性能有了初步了解。 -
1. the author designs special equipment with double - deck, based on the ultimate analysis, caloric, thermodynamic characteristic parameter of layer boiler, working fluid parameters in and out of boiler, exhaust temperature, thermal loss, excess air coefficient, etc. according to processing technology, make special combustion equipment. and it is installed and debugged as required
根據生物質成型燃料的燃燒特性、層燃鍋爐熱性能及熱力特性參數為設計依據，設計出雙層爐排生物質成型燃料專用燃燒設備；根據燃燒設備的加工工藝製造出生物質成型燃料專用燃燒設備；按照燃燒設備安裝方法及調試方法對該燃燒設備進行了安裝與調試。 -
According to the theory of engineering thermodynamics and phase change, heat - transfer process of the special working fluid heat - pipe stove is analyzed. some hypotheses are postulated and with the help of equation of mass - conservation, energy - conservation, the dynamic concentrative parameter model is built, the change of each parameter is prescribed at any stage from starting to stopping. with the thermodynamic calculation of burnable process, the parameter of device, such as heat - transfer coefficient / thermal efficiency etc, are achieved under steady state ; based on theoretic calculation, observing the actual running circumstance of the heating stove in person, with some performance comparison between the new and the old, the high efficiency and reliability of heat - pipe stove is proved, the project which expend it in the oil - filed is feasible
對充入該工質的熱管加熱爐，本文根據工程熱力學和相變傳熱學及相關知識，對其進行了傳熱分析，經過適當假設，運用質量守恆和能量守恆定律，建立了裝置動態集中參數模型，描述了加熱爐從開機到穩定運行這一動態過程各參數的變化情況，同時對燃燒過程也進行了熱力計算，最終得到了穩態工況下裝置的換熱系數、熱效率等熱力參數；在理論計算的基礎上，親赴現場觀察該爐的實際運行情況，通過與原有的加熱爐的各項性能進行對比，最終證明新爐的高效性和可靠性，為其在油田中推廣的可行性提供了依據。 -
In this paper, the working fluid is air. experimental study of the nine different structure parameters of 3 - d ift with staggered arrangement fins in the reynolds number range of 250 to 30000 is performed to investigate the characteristics of heat transfer and flow friction behavior. analyses and reduces the experimental data by the least square method, obtains the nusselt and fanning friction fitting criterion equations
本文以空氣為工質，在re 250 30000范圍內對九根具有不同肋形結構尺寸的肋叉排三維內肋管的換熱及流動特性進行了研究，並運用最小二乘法分析和處理實驗數據，獲得努謝爾特數，范寧摩擦系數與雷諾數，肋幾何參數的準則方程式。
分享友人