written-out program 中文意思是什麼
written-out program
解釋
輸出程序-
The building builds careful material : commodity house beforehand ( annul ) carry out licence or room change written reply to a subordinate body ; build project program licence ; build engineering construction permit ; build licence of the program that use the land ; state - owned land uses card ; propose careful ichnography and floor plan
房屋建審資料：商品房預（銷）售許可證或房改批復；建設工程規劃許可證；建設工程施工許可證；建設用地規劃許可證；國有土地使用證；建審平面圖及樓層平面圖。 -
In the hardware design, the paper completes modules ’ design like outside memory, patulous a / d, patulous d / a, rs232 communication, ecan communication, led control, keyboard control, distant control, emulation, reset, logic voltage switch, dsp supply power regulate and ac - dc power circuit, as well as room layout design like anterior panel, back panel etc. and dsp transfers data with peripheral equipments except outside memory using serial ports. besides, the whole circuit is configured in interrupt response. thus, it can meet system demand as well as take full advantage of tms320f2812 ’ s hardware resource. in the software design, the paper finishs programs like the interface programms intercommunicates with people, the distant control program, ad and da modules ’ control program, in addition, the paper select the velocity and acceleration state - feedback algorithm and is written in the program. the software design uses dsp integrate exploiting environment named ccs2. 2 of ti inc. as software instrument, and programs with the combination of c language and assembly language. moreover, in order to maintenance or modify the software expediently and shorten software ’ s exploitation time, the design adopt software modularization technique. finally, some air cylinder experiments are carried out to proved that the pneumatic controller is very practical
在硬體設計中，本文完成了片外存儲器擴展、 a / d擴展、 d / a擴展、 rs232通信介面、 ecan通信總線介面、液晶顯示控制、鍵盤控制、遠程控制、模擬、復位、邏輯電平轉換、 dsp工作電源校正電路和ac - dc電源等模塊設計以及控制器前面板、後面板等的空間布局設計。其中dsp與除外部存儲器的外圍設備之間的數據傳送全部採用串口通信，同時系統電路配置成中斷響應方式，這樣既滿足了系統要求，又充分利用了tms320f2812的硬體資源。在軟體設計中，本文完成了人機界面功能模塊、遠程控制模塊、 ad擴展模塊、 da擴展模塊、速度和加速度狀態反饋的控制演算法的程序設計。 -
In this paper, the relation among highway alignment, vehicle operating velocity, vehicle fuel consumption and vehicle dynamics is discussed synthetically. to evaluate and optimize the design of highway alignment, a " high alignment - vehicle move and system dynamic response " model has been established. by using the computer program of the system, which is written with visual c + + 6. 0, one could easily draw out the variation curves of vehicle operating velocity, vehicle fuel consumption and some certain vehicle dynamics index
公路線形設計以汽車行駛規律為出發點，本文嘗試以汽車系統動力學的觀點研究道路線形設計問題，針對目前設計中存在的一些問題，建立了「公路路線? ?汽車運行響應模型」 ，分為行駛速度、耗油量預測和動力學響應計算兩大模塊，主要是為了克服傳統汽車理論在指導公路路線設計時過于簡化汽車，只考慮計算行車速度的弊端，力圖通過建立「路線方案? ?行駛車速? ?力學響應」相互之間的量化關系模型，為公路線形指標的選取和優化提供一定的參考價值。 -
If the program turns out to be reasonable to generalize a bit, generalize it, and you will have written a utility
如果事實證明該程序更通用化一點是合理的，那就通用化它，這樣您就編寫了一個實用程序。
分享友人