zero point error 中文意思是什麼
zero point error
解釋
零點誤差-
The algorithm and its implementation of the leading zero anticipation are very vital for the performance of a high - speed floating - point adder in today s state of art microprocessor design. unfortunately, in predicting " shift amount " by a conventional lza design, the result could be off by one position. this paper presents a novel parallel error detection algorithm for a general - case lza
目前國際上已有很多演算法對前導0預測演算法進行了研究，但是出於設計方法和延遲等方面的限制，大部分前導0預測演算法都為非精確演算法，其預測結果可能與真實加法結果中前導0的個數產生一位的誤差，這個誤差需要在浮點加法的后規格化過程中進行修正，因此反過來又增加了浮點加減演算法的關鍵路徑延遲。 -
For these reasons, we can apply the theory of the model reference self - adaptive control syetem design based on the theorem of balance point stabilization in the force system of asymmetric cylinder controlled by symmetric valve. the main idea of model reference self - adaptive controller is to make the self - adaptive control error incline to zero as time passed. the task to design adaptive controller is to find the control input that can make the output of the controlled system to follow that of the reference model
因此將基於平衡點穩定定理的模型參考自適應控制系統設計理論應用於閥控非對稱缸力系統中，其基本原理是使自適應控制誤差隨時間的推移而趨向于零，自適應控制器設計的目的是尋找使被控系統的輸出漸近一致的跟隨參考模型的輸出的控制輸入，以此來改善被控系統的性能。 -
A resolution method in software is applied to calibrate zero point and full scale of the circuit. software approach to nonlinear correction for sensor and circuit is presented. therefore system error is eliminated, and measurement accuracy of temperature is improved. the signal of acidity electrode is detected by a differential amplifier circuit, which consists of operational amplifiers tlc2254 with high input impedance and low drift
採用橋路和單運放差動放大電路對溫度傳感器信號檢測放大，軟體校正溫度傳感器和測量電路的非線性，軟體校準測量電路的零點和滿度，消除測量電路的系統誤差，提高補償溫度的測量精度；採用高阻、低漂移運放tlc2254組成高阻差動放大電路用於酸度電極信號測量。 -
Then one of the methods of rotor position detection - bemf zero crossing point detection is explained in detail. in succession, the chapter dissertates the method of measuring phase voltage and supply voltage, and analyses the error of rotor position using this method
對轉子位置檢測方法中的反電勢過零點法作了比較詳細的介紹，討論了反電勢法中相電壓和端電壓的檢測方法，並分析了利用該方法時而產生的轉子位置檢測誤差。 -
Second, as currently study of hot point, back ? emf, it will discuss the principle of the sub - position examination in detail. based on the principle, it put forward a kind of improving back - emf method of crossing - zero checking turns position. but this did n ' t resolve to the root problem that the speed scope is very narrow and it need an in expiation of speed error and so on. thus it put forward a new improvement method at next chapter
其次，就目前所研究的熱點? ?反電勢法，詳細討論了其轉子位置檢測的原理，在此基礎上提出了一種改進的反電勢過零點檢測方法，其可直接從電機端部得出反電勢對地的電壓值，而不是通過電機中心點電壓來得到反電勢。 -
The figure below shows the magnitude of the error that results from a 1 % error in recording either i0 ( intensity of fluorescence at zero - pressure oxygen ) or the intensity at the high calibration point
下圖表明了誤差值，記錄中結果為1 %誤差或i0 （在零壓力氧下熒光強度）或在高校準點下的強度。
分享友人