介質擊穿 的英文怎麼說
中文拼音 [jièzhíjīchuān]
介質擊穿
英文
dielectric breakdown-
In the case of dielectric breakdown, a different type of acceleration occurs.
在介質擊穿的情況下，出現了一種不同類型的加速。Simulation of water pulse forming line switch with prepulse suppression ground plane
具有預脈沖屏蔽板的水介質自擊穿開關的電路模擬This paper discusses the most suitable design of the homocentric ball capacitor on the condition that the maximum pressure endurance is limited and the puncture field is strong
摘要討論了在限定最大耐壓值及介質的擊穿場強的情況下，同心球形電容器的最佳尺寸設計。Investigation of a low prepulse multi - channel self - breaking water switch
低預脈沖水介質多通道自擊穿開關實驗研究A study on heat exchange cycles of endo - reversible variable temperature in engines
介質阻擋放電擊穿場強影響因素的研究Using two - dimensional numerical simulation software, analyze the affect of isolated - trench ' s parameters on the breakdown voltages of three - class bipolar power devices ( whose ideal breakdown voltages correspond to 40v, 70v and 100v ), which include width, depth, isolated material ' s dielectric constant, fixed interface - charge and field plate located at the top of deep - trench termination
利用二維數值模擬軟體分析了影響三類典型應用的雙極功率器件（對應的理想擊穿電壓bv _ （ cro ）分別為： 40v ， 70v ， 100v ）擊穿電壓的諸多因素（主要包括阱寬度、阱深度、阱內填充介質、界面固定電荷、阱區頂端場板） 。The simulation results indicate, deep - trench junction termination with certain width, depth and filling with isolated dielectric can increase the avalanche breakdown voltage of devices to above 95 % of the ideal value
結果表明：具有一定寬度、深度且填充絕緣介質的深阱結終端結構，阻止了結的橫向擴展，並能將器件的雪崩擊穿電壓提高到理想值的95以上。Test method for evaluation of resistance to electrical breakdown by treeing in solid dielectric materials using diverging fields
應用相異場評估固體介質材料電擊穿電阻的試驗方法Experimental study on circuit parameters and breakdown properties of water switch under pulsed voltage
脈沖電壓下的自擊穿水介質開關擊穿特性和電路參數實驗研究Characteristics study of short - pulsed dielectric breakdown in liquids
液體介質快脈沖電壓下擊穿特性研究A breakdown model of dielectrics, which exists some blemish inside or on the surface, such as hole, impurity and heave at which breakdown probability is larger than that at other points, was established
建立了含有缺陷點的絕緣介質擊穿模型，指出電纜絕緣層內部及表面存在空洞、夾雜物和隆凸不平是缺陷產生的內在因素，缺陷點處的擊穿概率較大。According to the thickness of the soi film, high voltage ic based on soi material ( soi - hvic ) can be divided into thin - film and thick - film. for thin - film soi - hvic, linear drift region doping profile is adopted to satisfy a certain breakdown - voltage, but this process is too complex and its self - heating effect is obvious ; for thick - film soi - hvic, it can take advantage of cmos technology on silicon to obtain the high voltage
Soi高壓集成電路根據頂層硅厚度可分為厚膜和薄膜兩大類。為了滿足一定的擊穿電壓，薄膜soi高壓電路一般採用漂移區線性摻雜技術，但其工藝復雜，且自熱效應嚴重;而厚膜soi高壓集成電路可以通過移植體硅cmos技術來實現高壓，但是由於其硅膜較厚，介質隔離成為厚膜soi高壓集成電路的關鍵技術。A state monitoring method of power cable based on the analysis of dielectric breakdown characteristic was presented
摘要在對絕緣介質擊穿特性分析的基礎上提出了一種電力電纜狀態監測方法。Aluminium and aluminium alloys - anodizing - determination of electric breakdown potential
鋁及鋁合金.陽極化.電介質擊穿潛在性的測定Standard test method for dielectric breakdown voltage of insulating oils of petroleum origin under impulse conditions
在脈沖條件下石油成因的絕緣油的電介質擊穿電壓的標準試驗方法Standard test method for dielectric breakdown voltage and dielectric strength of solid electrical insulating materials using impulse waves
用脈沖波法測定固體電絕緣材料的電介質擊穿電壓及抗電強度的標準試驗方法10. 02 test method for dielectric breakdown voltage and dielectric strength of solid electrical insulating materials using impulse waves
用沖擊波測定電氣固體絕緣材料的電介質擊穿電壓和介電強度的試驗方法Standard test method for verifying the specified dielectric withstand voltage and determining the dielectric breakdown voltage of a membrane switch
薄膜開關的規定的介質抗電強度的驗證和介質擊穿電壓測定的標準試驗方法Aluminium and aluminium alloys - anodizing - part 17 : determination of electric breakdown potential ; german version en 12373 - 17 : 2001
鋁及鋁合金.陽極氧化.第17部分:電介質擊穿潛能測定Dielectric breakdown characteristic and state monitoring method of power cable
電力電纜介質擊穿特性和狀態監測方法分享友人