位置控制迴路 的英文怎麼說

中文拼音 [wèizhìkòngzhìhuílù]
位置控制迴路 英文
position control loop
  • 位 : Ⅰ名詞1 （所在或所佔的地方） place; location 2 （職位; 地位） position; post; status 3 （特指皇帝...
  • 置 : 動詞1. （擱; 放） place; put; lay 2. （設立; 布置） set up; establish; arrange; fix up 3. （購置） buy; purchase
  • 控 : 動詞1 （告發;控告） accuse; charge 2 （控制） control; dominate 3 （使容器口兒朝下 讓裏面的液體慢...
  • 制 : Ⅰ動詞1 （製造） make; manufacture 2 （擬訂; 規定） draw up; establish 3 （用強力約束; 限定; 管束...
  • 路 : 1 （道路） road; way; path 2 （路程） journey; distance 3 （途徑; 門路） way; means 4 （條理） se...
  • 控制 : control; dominate; regulate; govern; manage; check; cybernate; manipulate; encraty; rule; rein; c...
  1. Pre - data gathering module achieves the collection and communication of sixteen - route temperature signal. speed measuring and controlling module realizes the control of refolw soldering transfer speed by manipulating transducer. on - off outputting module fulfills calefaction control of calefaction tube by solid state relay. above position operator software programs by delphi, and realizes pid parameter automatic timing and no - oversnooting temperature control. software has friendly interface, convenient operation, complete functions

    前置數據採集模塊完成16路溫度信號的採集和通訊；速度測量模塊與速度控制模塊通過控制變頻器來調節迴流焊的傳輸速度；開關量輸出模塊通過固態繼電器對加熱管進行控制；上位機軟體採用delphi編程，實現了pid參數自整定以及無超調的溫度控制。
  2. A new full - wave measurement circuit structure is put forward that would increase distribution automation system reliability and veracity. the distributed protection and monitoring unit in this paper can instead of general instruments of low voltage distribution system. it not only combines ampere meter, voltage meter, active power meter, reactive power meter and power meter, frequency meter into a meter, but also increases monitoring position switch, control bus switching alternately and monitoring energy

    本文研製的保護和測控單元，可替代低壓配電系統中所使用的常規儀表，將原來迴路需要的電流表、電壓表、有功功率表、無功功率表和功率因數表、頻率表簡化為一塊表，並增加了位置開關量檢測，控制母線投切和電度監測功能，從而極大的簡化了低壓配電二次儀表設計、安裝調試，提高了運行、維護和管理水平。
  3. The proposed control system includes the attitude controller acting on the rigid hub, designed by using pulse - width pulse - frequency ( pwpf ) modulation integrated with command shaping technique based on csvs method, and the piezoelectric material elements as sensors / actuators bonded on the surface of the beam appendages, designed by the optimal positive position feedback ( oppf ) control technique, in which the selection of ppf gains is determined via introducing a cost function to be minimized by feedback gains which are subject to the stability criterion at the

    設計的控制器僅利用輸出信息，從而避免設計撓性模態狀態觀測器以及引入狀態觀測器誤差;在此基礎上，採用分力合成方法設計命令成形控制器來抑制撓性附件的振動，設計的優化命令成形控制信號在理論上可以對系統的各階撓性模態完全抑制。但考慮到模型不確定性和外部擾動，在內迴路又設計了最優正位置反饋（ oppf ）補償器以增加撓性結構的阻尼，使撓性結構的振動能夠很快衰減。
  4. Finally, signal waves of every part of the system were tested and adjustment of the position loop and velocity loop control parameters were finished

    最後，測試了系統中各部分電路的信號波形，完成了速度迴路和位置迴路控制參數的整定。
  5. Two control circuits were designed in the paper : gear control circuit and throttle control circuit. and corresponding fuzzy control arithmetic was studied to control engine work point

    對發動機工作點的控制，本文設計了兩控制迴路（擋位控制迴路和油門位置控制迴路）實行調節控制，並研究了相應的模糊控制演算法。
  6. Control arithmetic of position loop and velocity loop has been realize in the digital controller, whose output is pwm signal with adjustable occupy rate which is put in the driving circuit to realize motor ’ s position and velocity control

    在數字控制器中實現位置迴路和速度迴路的控制演算法，其輸出為可調占空比的pwm信號經驅動電路實現電機的位置和速度控制。
  7. Taking the industrial computer as the kernel, the system structure was simplified by extending the multi - channel in one piece of cpld, the servo - control precision and working stability were improved effectively by the full digital sample of the signal for speed circuit and position circuit. and the advantages of the system are simple 、 low ? cost and stable

    以工控機為核心，在位置反饋信號採集調理過程中對單片cpld進行多通道擴展以簡化系統結構，並通過對速度迴路和位置迴路的信號的全數字采樣，有效的提高了伺服控制精度及工作穩定性，使系統具有結構簡單、成本低廉、性能可靠等特點。
  8. Mounts motors, transformers, controllers and lighting fixtures into position and completes circuits according to diagram specifications

    安裝電機、變壓器、控制器和照明器材到指定位置，並根據圖紙描述完成整個迴路。
  9. Adopted in computer vision detection, the single - needle quilting controlling system possesses brilliant future because of three points : on the one hand, it conducts real - time supervision on processing track, which equals to importing computer vision to location controlling loop, on the other hand, it is easy to generalize to processing and controlling field of common flexible workpiece

    在單針絎縫控制系統中把計算機視覺引入位置控制迴路，實現對加工軌跡的實時測控，在國內未見有相關成果報道。這種方法推廣到一般的柔性工件加工控制領域，將具有廣闊的應用前景。
分享友人
分享到 Line

分享到臉書