位置線 的英文怎麼說
中文拼音 [wèizhìxiàn]
位置線
英文
line of position, lop-
Based on these theories, this paper discusses the method of design of the rectangular gunn integrated active microstrip patch antenna in detail. the size of the active antenna and the location of the device in the antenna is obtained at the specified operation frequency
根據這些理論,詳細討論了一種集成gunn二極體的矩形有源微帶貼片天線的設計,得到了在給定的工作頻率下的有源天線尺寸和有源器件的位置。Position the aerial for the best reception.
把天線安裝在接收效果最好的位置上。Secondly, programmed the image processing arithmetic code which include the bottom arithmetic for the general condition comprises threshold division, region combination and informate and the middle level arithmetic for the given task comprises detecting the line dation creirection according to the hough transform in order to fix on the hole ’ s azimuth angle, detecting the aiguille tip position according to the image movement according to the environment and the image format
然後,根據目標環境要求和攝像機採集圖像格式,開發了圖像處理演算法程序。圖像處理演算法包括底層演算法和中層演算法兩部分,底層演算法針對通用情況,包括閾值分割、區域合併和信息生成。中層演算法針對具體任務設計,包括利用hough變換檢測棱線的方向,從而確定圓孔的方位角和利用基於圖像運動檢測鉆頭尖端位置。On the basis of the basic theory of metal distortion, using round steel alit rolling as entity model and combining with production practice, the selection of slit location, slit mode and the design parameter of slit pass system were analyzed, and the area calculation model of pre - slit rolled piece and slit rolled piece was built
摘要基於金屬塑性變形基本理論,以圓鋼雙線切分為基本實體模型,結合生產實踐,對切分位置、切分方式的選擇和切分孔型系統的設計參數進行了分析,並建立了預切分軋件和切分軋件的面積計算模型。The riding position of signal wire was not always in the vertex of the impression from the conclusions of production, but in the position in which aluminous liquid tilted at last
由生產實踐總結出信號線的安放位置不一定在型腔最高點,而應在金屬液最後充填的位置。Besides, the paper presents a simple but useful method of isoline labeling, azimuth angle judgement algorithm
在等值線標注部分,採用簡單實用的向量判斷法,確定標注的位置。This paper describes an automatic contest robot from the cctv holding “ the first robot tv contest all over the academician ”, describes the function and the realization of the robot in greater detail. the robot adopts two stepper motors in the stepped driving control system and putting - ball control system like fishing, with the control of at89c52 single - chip microcomputer, it can synchronously produce driving pulse for two stepper motors and control the moving of the robot along the predetermined line
該競賽機器人採用步進電機作為行走驅動,釣魚桿式的放球控制系統,在at89c52單片機的控制下,分別為左、右步進電機產生脈沖,控制機器人按照預設的固定路線行走,待機器人到達預定的目標位置后,同時控制多個放球機構,從而能分別將賽球準確地放入到比賽圓筒中。Detecting ice blockage position of gas pipeline
輸氣管線冰堵段位置測量的研究Nibco iron body check valves may be installed in both horizontal and vertical lines with upward flow or in any intermediate position
尼伯科鑄鐵閥體止回閥可以安裝在水平管線或流向朝上的垂直管線中的任何位置上。Loran position line
羅遠位置線Position line standard error
位置線標準誤差According to more effect, when the hore component is placed in a gradient field, at the same time the direction of the current is perpendicular to the direction of the voltage, then between the two parallel side face come out the hore voltage. when hore component is set in this kind of uni - gradient magnetic field and the electric current is unchanged, the voltage output of hore component will be proportional to the position of the hore component in the magnetic field. so we can use the hore component to measure the movement of hore component against magnetic field
根據霍爾效應可知,置於磁場中的霍爾元件若電流方向與磁場方向垂直,則在霍爾元件垂直於磁場和電流方向的兩個側面將產生電勢,將霍爾元件置於強度隨空間位置線性變化的磁場中,且控制電流恆定,輸出就正比于霍爾元件處于磁場中的位置,因此可以用霍爾元件來測量磁場與霍爾元件間的相對位移量。Use, installation and maintenance 1. align the white colored timing scale mark on engine timing gear with the position line of engine timing scale mark
將發動機正時齒輪上正時刻度白色標記線撥至與發動機正時標記位置線對齊。Visual line of position
目測位置線Position line by distance difference
距離差位置線Position line by distance
距離位置線In addition, the response character of solenoid valve was analyzed for different structure and lead diameter of solenoid valve
分析了電磁閥在不同的線圈視窗尺寸及位置、線徑及匝數下電磁力的大小及其對電磁閥響應特性的影響。The hot austenite grain distribution and the phase composition at normal temperature were obtained with the aid of metallographic analysis method after the rolled workpieces were divided at the specified position on the linear cutting machine
對軋后工件進行指定位置線切割取樣,並用金相分析法得到變形后工件的高溫奧氏體晶粒尺寸分佈及低溫相組成。Gradient of position line
位置線梯度Position line transferred
轉移位置線分享友人