供油噴嘴 的英文怎麼說

中文拼音 [gōngyóupēnzuǐ]
供油噴嘴 英文
feed nozzle
  • 供 : 供Ⅰ名詞1 （供品） offerings 2 （口供; 供詞） confession; deposition Ⅱ動詞1 （供奉） lay （offerin...
  • 油 : Ⅰ名詞1 （脂肪; 油脂） oil; fat; grease 2 （姓氏） a surname Ⅱ動詞1 （用桐油、油漆等塗抹） apply t...
  • 噴 : 噴動詞1. （液體等受壓力而射出） spurt; spout; gush; jet 2. （噴灑） spray; sprinkle
  • 嘴 : 名詞1. （口的通稱） mouth 2. （形狀或作用像嘴的東西） anything shaped or functioning like a mouth 3. （指說話） talk; speak
  1. The main achievements are as follows : 1 it ' s for the first time to extensively investigate effects of main combustion system parameters such as plunger diameter, plunger stroke, fuel delivery advanced angle, valve opening pressure of nozzle on performance of dme engine. the parameters are optimized

    取得的主要成果有： 1系統地研究了油泵柱塞直徑和行程、供油提前角、噴嘴啟噴壓力等發動機燃燒系統主要參數對二甲醚發動機性能的影響，優化了這些參數。
  2. Using compressed air and transformer oil as working substance, this paper studied the pressure characteristic of internal - mixing nozzle and acquired the experimental relation on the pressure in the mixing chamber of internal - mixing nozzle against the operation parameters and structure parameters according to the method of step by step regression

    摘要以壓縮空氣和變壓器油為工質對內混式介質霧化油噴嘴的流量特性進行實驗研究，並通過逐步回歸分析的方法獲得了內混式介質霧化噴嘴油、氣流量系數與運行及結構參數的實驗關系式，可供設計使用部門參考。
  3. The construction of conical nozzle is used by pump ' s delivery - valve, making use of the dynamic characteristics of conventional. short pipe to enhance injection pressure. there are three parameters of fuel injection system : response pressure, injection - advanced angle, injection valve bulge high degree, the best match was found by adjusting them

    在油泵出油閥端，採取漸縮管結構措施，利用管路動態效應提高噴油壓力；對于噴油系統參數：噴油壓力、靜態供油提前角和油嘴凸出高度，三個參數進行調整試驗，找到它們的最佳匹配。
  4. However, by comparison with flap nozzle servo valve which has been used widely and popularly by now, the torque motor of jet pipe servo valve has a larger rotary inertia. this causes low natural frequency of servo valve, and thus the response speed of jet pipe servo valve is slow. moreover, the jet pipe of servo valve has large flexibility, and it is easy to excite oscillations and noise in the valve, which is named self - excited oscillations and noise

    然而與目前普遍使用的噴嘴擋板伺服閥相比，射流管伺服閥的銜鐵組件轉動慣量大，導致力矩馬達部分固有頻率低，從而響應速度慢，此外，射流管供油管柔性大，容易產生自激現象，這些缺點都使得射流管伺服閥的動態特性差，從而影響了它的工作性能。
  5. It ' s the first time to question extensively the influences of fuel delivery advance angle and injection pressure on performance of e30 engine

    首次系統地研究了供油提前角、噴嘴啟噴壓力對e30混合燃料發動機性能的影響。
  6. Heating boilers. part 2 : heating boilers with forced draught burners. special requirements for boilers with atomizing oil burners

    供暖鍋爐.第2部分:強制送風噴嘴式供暖鍋爐.帶霧化油燃燒器的供暖鍋爐的特定要求
分享友人
分享到 Line

分享到臉書