兩軸間旋動 的英文怎麼說

中文拼音 [liǎngzhóujiānxuándòng]
兩軸間旋動 英文
rotate between two axes
  • 兩 : Ⅰ數詞1 （數目） two 2 （表示不定的數目） some; a few Ⅱ量詞（市兩的通稱） liang a unit of weight ...
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  • 間 : 間Ⅰ名詞1 （中間） between; among 2 （一定的空間或時間里） with a definite time or space 3 （一間...
  • 旋 : 旋Ⅰ動詞1 （旋轉） whirl 2 （用車床切削或用刀子轉著圈地削） turn sth on a lathe; lathe; pare Ⅱ名詞...
  1. Strong and high effective mixing of swzzero gravity particle mixer can meet your demand. two mixing axles make a equal speed and reverse rotation in horizontal tube. oars on mixing axle make the materials do radial motion, circular motion and axial motion. in a short time, the particle can be stirred homoginously. nozzel on cover of tube can be used when the solid is mixed with liquid

    無重力粒子混合機（以下簡稱無重力）以強烈、高效混合而來滿足用戶需求，臥式筒體內兩根攪拌軸等速反向旋轉，攪拌軸等速反旋轉，攪攔軸上特殊布置的漿葉確保物料徑向、環向、軸向三向運動，形成復合循環，在極短的時間內達到均勻混合，筒蓋上布置霧化噴嘴供你固液混合時使用。
  2. Abstract : the calculation of the rigidity for the ball screw transmission system was discussed, including the axial rigidity of the screw, the axial rigidity of supporting bearing, the contact rigidity between ball and groove. the influence of the rigidity variation on the transmission accuracy was analyzed

    文摘:本文系統地討論了滾珠螺旋傳動系統的剛度計算，包括螺桿本身的軸向剛度、螺桿兩端支承軸承的剛度以及滾珠與滾道間的接觸剛度，並分析了剛度變化對傳動精度的影響。
  3. The dynamo runs at rull speed to drive main shaft, then the main shaft makes the emulsifying wings in emulsification grove rotate, which absorbs the liquid in its brand groove into ring groove through guide vanes on upper and lower sides of the groove. the vanes spins circularly at high speed with the main shatf as center, and the blade and emulsificaton groove cut and crush it continuously. after that. it gers squeezed by the vanes highspeed centrifugal rotation. at last, it finishes isotropt emulsification tratment within extremely short time after continuous circulating mixing

    由電動機全速運轉帶動主軸，經主軸轉動乳化框槽內之乳化翼片，使其將桶槽內之液體經框槽上、下兩側之導流葉片吸入環狀框槽內，經以主軸為中心高速圓周旋轉葉片；連續使乳化翼端刀面與乳化框間極小之間系高頻率之強力切割剪斷、粉碎，再借葉片高速離心旋轉排擠，持續循環混合，以極短之時間即可完成均質乳化之處理。
分享友人
分享到 Line

分享到臉書