判定型節點 的英文怎麼說

中文拼音 [pàndìngxíngjiédiǎn]
判定型節點 英文
decision type node
  • 判 : Ⅰ動詞1 （分開; 分辨） distinguish; discriminate 2 （評定） judge; decide 3 （判決） sentence; con...
  • 定 : Ⅰ形容詞1 （平靜; 穩定） calm; stable 2 （已經確定的; 不改變的） fixed; settled; established Ⅱ動詞...
  • 節 : 節構詞成分。
  • 點 : Ⅰ名詞1 （液體的小滴） drop （of liquid） 2 （細小的痕跡） spot; dot; speck 3 （漢字的筆畫「、」）...
  • 節點 : [電學] panel point; hybrid; packing; node; nodal points; joint of framework; pitch point; point pitch
  1. In anchoring effect, in addition to the influence of high and low anchor points on subjects price estimates, we also consider the moderating role of the operation of anchor points ( one - way / two way ), the reinforcement of anchor points ( normal / intensified ), and the relevancy between anchor and target ( relevant / unrelevant )

    在定錨效應的實驗中，除了考慮高低錨點值對受測者價格估計判斷之影響，同時亦探討錨點運作方式（雙向單向） 、錨點強化作用（強化一般） 、以及錨點訊息與估計標的物之間的語意相關性（相關不相關）等三個變數，是否會扮演錨點類型對決策者估計影響之調節角色。
  2. To analyze some key technologies of optical network relative with rwa in detail, such as transmission, switching and internetworking ; to emphasize on the research of function, fabric and performance of optical cross - connection ; to carry out numerical simulations for crosstalk introduced by optical cross connect and to present measurements for suppressing it such as doubly filtering, fixing optimum decision threshold and appropriately choosing the number of multiplexed wavelengths ; 3. to research the fundamental principle and some problems relative with rwa, including the type of optical network, the type of traffic, the type of service, the survivability of optical network ; to classify and compare rwa algorithms and particularly research some dynamic rwa algorithms ; 4. to present reserved light - path and classify network resource such as used, unused and reserved status, to emulate establishment of all - optical connection in optical network through modified rwa algorithm and show effectively reducing setup time of all - optical connection utilizing reserved light - path ; to research rwa algorithms of multi - fiber network, to present new link weight functions dependent on node degree, unused fiber ( s ) per wavelength - layer and routing policies, to perform emulation of rwa based wavelength layer graph applying new link weight functions and show them make algorithms better performance and network lower blocking rate ; 5

    詳細分析了與rwa相關的光網路關鍵技術，包括傳輸、交換、組網等，重點研究了光交叉連接的功能和結構、性能，對其引入的串擾進行了詳細分析，選擇恰當的器件參數進行了數值模擬，並提出了抑制措施（如雙重濾波、優化判決門限、選擇恰當的復用波長數） ; 3 .研究了光網路的r認叭的基本原理、與r認叭的幾個相關問題（光網路類型、業務類型、流量類型、光網路生存性） 、 r認人演算法的分類和比較，具體研究了幾種動態r場人演算法; 4 .研究了以全光連接建立時間為優化目標的r認認演算法，提出預置光路的概念，對網路資源進行狀態分類（佔用、未佔用、預置） ，利用改進的r認叭演算法模擬，預置光路可為部分新到的連接請求快速建立連接，從而提高網路性能;研究了以多光纖網路連接阻塞率為優化目標的r認城演算法，提出了以節點度數、每個波長分層的空閑光纖數以及路由策略決定的幾種鏈路權重函數，利用基於波長分層圖模型的并行r場人演算法模擬，利用新的鏈路權重函數使得演算法具有更優的性能，使網路具有更低的連接阻塞率。
  3. Thirdly, subspace iterative method is adopted in the paper, and natural periods and modes of preceding fifteen steps of zhongshan no. one bridge are solved, dynamic characteristics of this kind of structural system are obtained, inherent link between dynamic characteristics and structural rigidity is discussed deep, the viewpoint is provided that dynamic characteristics of a structure are considered as important basis whether structural scheme is rational ; in addition, the author brings out some own views and opinions about calculational methods of prestress value of different sorts of tie rods, simulation of local rigidity region, foundation of a local finite element model of a node

    另外，提出在施工階段中某些構件的應力有可能比成橋狀態的應力還大，需防止在施工狀態中構件因強度不足而破壞；再次，採用于空間迭代法，求解了拱式組合體系橋梁的自振周期和振型，得出該種結構體系的動力特性，深入探討了動力特性和結構剛度之間的內在聯系，提出了把結構的動力特性作為判斷結構方案是否合理的重要依據。此外，本文還就系桿預應力值的確定方法、局部剛度區域的模擬、節點局部有限元分析提出了作者的見解和看法，對解決類似問題得出了一些有參考意義的結論。
  4. Based on the model, the thesis proposes the algorithm deciding the important manufacturing process, which can be used to decide the important parts of manufacturing process ; and proposes the algorithm affecting unqualified index of manufacturing quality, which can be used to find the process affecting the unqualified index

    基於該模型，提出了重點工序確定演算法，用於確定製造過程中需要重點控制的質量環節;提出了不合格指標相關工藝判定演算法，用於快速找出質量檢驗中影響不合格指標的相關工序。
分享友人
分享到 Line

分享到臉書