割槽 的英文怎麼說
中文拼音 [gēcáo]
割槽
英文
kerf-
During fabrication slots for the stringers flanges were flame cut into box girders.
製造時,為安裝縱梁翼緣,在箱型梁中用焰割法開槽口。Key way cutting construction on binding face of new and old concrete for dam heightening of danjiangkou project
丹江口大壩加高工程新老結合面鍵槽切割施工The dynamo runs at rull speed to drive main shaft, then the main shaft makes the emulsifying wings in emulsification grove rotate, which absorbs the liquid in its brand groove into ring groove through guide vanes on upper and lower sides of the groove. the vanes spins circularly at high speed with the main shatf as center, and the blade and emulsificaton groove cut and crush it continuously. after that. it gers squeezed by the vanes highspeed centrifugal rotation. at last, it finishes isotropt emulsification tratment within extremely short time after continuous circulating mixing
由電動機全速運轉帶動主軸,經主軸轉動乳化框槽內之乳化翼片,使其將桶槽內之液體經框槽上、下兩側之導流葉片吸入環狀框槽內,經以主軸為中心高速圓周旋轉葉片;連續使乳化翼端刀面與乳化框間極小之間系高頻率之強力切割剪斷、粉碎,再借葉片高速離心旋轉排擠,持續循環混合,以極短之時間即可完成均質乳化之處理。The notch cut into a key that corresponds to such a ridge
鑰匙的榫槽鑰匙上切割出的對應鎖眼的凸槽Cutting, notching, mitring, welding, fabricating, drilling, delivery, unloading, handing, assembling, hoisting, fitting and fixing in position, bedding, filling in solid and pointing including necessary lugs or other attachments
切割、開槽、法冠接、焊接、製造、鉆孔、交貨、卸載、處理、裝配、提升、原位裝置和固定,打底、固后填充以及勾縫,包括必需的拖線片或其它附件。A groove or notch made by a cutting tool, such as a saw or an ax
鋸縫,劈痕切割型工具如鋸或斧子所製造的溝槽或凹口Roll mat - - - can be cut and fit into different types of cavity wall, can be installed into any position of the construction, especially the long and nonblocked area, such as the roofing of metal building ; the slot of power lines, water pipes
卷氈- - -經切割可以用於任意尺寸的墻體空腔,安裝于建築的任意部位,特別是長而無阻塞的區域,如鋼結構屋頂;電線管、水管通過的槽隙等。Sawblade for ripping and cross cutting of softwoods and hardwoods up to 50mm and single or multiple chipboard panels up to 60mm with good finish. use on table saws
用於切割各種塑料雙貼面刨花板的預劃槽,以消除貼面崩裂現象。鋸片寬度從2 . 8毫米可調到3 . 6毫米。On the basis of brief introduction of danjiangkou dam extension project which is in the middle route water resources project of the south - to - north water diversion, the present construction methods and existing problems about key technology of increased artificial concrete keyway of jointing surface between new concrete and existing concrete are analyzed, and a new construction method by saw - cutting and static crack for construction of concrete keyway is researched
摘要在簡要介紹南水北調中線水源工程丹江口大壩加高工程概況的基礎上,針對大壩加高中新老混凝土結合面新增人工鍵槽施工的關鍵技術,分析了現有施工方法及存在問題,研究並提出了新的鋸割靜裂法施工法。The pipe extrusion machine set works through applying single - screw extruders to extrusion, vacuum mold to molding, cooling tank to cooling, hauling engine to drawing, and saw or planet cutter to cutting
本款管材擠出機組工作原理是:由單螺桿擠出機機頭擠出,型模真空定型,冷卻槽冷卻,牽引機引出,鋸切機或行星切割機最後進行切割。分享友人