匯編程序單位 的英文怎麼說

中文拼音 [huìbiānchéngxùdānwèi]
匯編程序單位 英文
assembly unit
  • 匯 : Ⅰ動詞1 （匯合） converge 2 （聚集; 聚合） gather together 3 （通過郵電局、 銀行把款項劃撥到別處）...
  • 編 : Ⅰ動詞1 （編織） weave; plait; braid 2 （組織; 排列） make a list; arrange in a list; organize; gr...
  • 程 : 名詞1 （規章; 法式） rule; regulation 2 （進度; 程序） order; procedure 3 （路途; 一段路） journe...
  • 位 : Ⅰ名詞1 （所在或所佔的地方） place; location 2 （職位; 地位） position; post; status 3 （特指皇帝...
  • 匯編 : 1 （把文章、文件編在一起） collect and edit; compile; assemble 2 （編在一起的文章、文件等） assem...
  • 程序 : 1 （進行次序） order; procedure; course; sequence; schedule; ground rule; routing process 2 [自動...
  1. They clearly identified 27 words / syllables in specific brain wave patterns and produced a computer program with a brain wave vocabulary

    他們清楚的證明了27個單詞位元組的特定腦電波模式並編制了一個關于腦電波詞匯表的電腦程序。
  2. This paper introduces the development process of wastewater disposal, it ' s auto control system, the level of nowadays and several new techniques of china and foreign countries. the immanent structure, control rules, main features and design methods of auto control systems in wastewater disposal process are studied in this paper. aiming at four typical parameters, such as temperature, dissolved oxygen, ph and the planes of water, the distributed control system is designed, composed by pc called epigyny computer and scm 8098 called hypogyny computer, and some sensors, shift deliver utensils and related meet orifices of parameters gathering and figures communication

    本文介紹了國內外污水處理及其自動控制系統的發展過程、當今水平和提高自動化程度的若干新技術；研究了污水處理自動控制系統的內在結構、控制規律、主要特點和設計方法；選取污水處理中的典型參數溫度、溶解氧、 ph值和液位等為控制對象，設計了以個人計算機為上位機、以8098單片機為下位機，並輔之以傳感器、變送器及相關介面單元所構成的二級集散控制系統（ dcs ） ；介紹了幾個主要程序模塊的設計思路、工作過程，這些程序模塊是：用高級語言visualbasic6 . 0開發的上位機人機交互界面程序、數據處理和圖表輸出程序，用執行效率高的匯編語言開發的下位機數據採集與系統監控程序、上位機與下位機之間的數據通信程序，匯編語言與vb之間的轉接程序，等等。
  3. The lower computer system software was developed with 8098 assemble language of mcs - 96 series and composed of modules of main program, time interrupt service routine, receiving interrupt service routine, data collection subroutine, data processing subroutine and control subroutine

    下位機系統軟體採用mcs - 96系列的8098單片機匯編語言來開發，主要由主程序模塊、定時中斷服務程序模塊、接收中斷服務程序模塊、數據採集子程序模塊、數據處理子程序模塊和控制子程序模塊組成。
  4. In hardware system design, we adopted the microcontroller of at89c51 as the main controller of inferior processor, it is used to connect the modem with the data acquisition module. mcs - 51 assemble language is used to program the software of the device to realize the data transmission between modem and inferior processor. when the electric power in the run is beyond the specified value, the inferior processor can dial the phone number of central computer automatically to send the alarm message through the communication line. using a single - chip microcomputer to control a modem to transmit remote datas are introduced in detail

    隨后詳細地介紹了系統的總體設計思想和具體的實現過程。在硬體系統設計中，採用了at89c51單片機作為下位機主控制器，用於連接modem和數據採集模塊。通過使用mcs51匯編語言編寫程序，實現了下位機與modem之間的數據傳輸，同時實現了自動檢測負荷，進行撥號報警的功能，其中重點介紹了單片機控制modem進行遠程數據傳輸的方法。
  5. Based on the requirements of the system the power source, amplify circuits, data gathering and storage circuit and reset circuit were designed. the software of this system was programmed with c language of mcs - - 51 single chip microcomputer that is a language of structijral programming language, cofltains many " characters of advanced ianguages and has the functions of assemble 1anguage. the software of the system was designed with structural program module that make the sttucture of software clear and convenience debug and modify

    其中系統硬體設計主要是採用mcs ? 51單片機為肌肉嫩度測量儀的核心，進行了系統電源設計、放大電路設計、數據採集和存儲電路設計、復位電路設計；軟體設計使用單片機c ? 51語言，它是一種結構程序設計語言，兼顧了多種高級語言的特點，並具備匯編語言的功能，根據程序設計原理，採用結構化程序設計，使軟體結構清晰。
分享友人
分享到 Line

分享到臉書