匹配負載功率 的英文怎麼說

中文拼音 [pīpèifùzǎigōnglǜ]
匹配負載功率 英文
matched load power
  • 匹 : Ⅰ動詞（比得上; 相當; 相配） be equal to; be a match for Ⅱ形容詞（單獨） lone Ⅲ量詞1. （用於馬、騾等） 2. （用於整卷的綢或布）
  • 配 : Ⅰ動詞1 （兩性結合） join in marriage 2 （使動物交配） mate （animals） 3 （按適當的標準或比例加以...
  • 負 : Ⅰ名詞1 （負擔） burden; load 2 （虧損） loss 3 （失敗） defeat Ⅱ動詞1 [書面語] （背） carry on th...
  • 載 : 載Ⅰ名詞（年） year : 一年半載 six to twelve months; six months to a year; 三年五載 three to five ...
  • 功 : 名詞1 （功勞） exploit; merit; meritorious service [deed]: 戰功 military exploits; 立功 render me...
  • 率 : 率名詞（比值） rate; ratio; proportion
  • 匹配 : 1. [書面語] （婚姻配合） mate; marry 2. [電學] matching
  • 負載 : [電學] load
  1. Thirdly, it simulated the pumping circuit & dividing circuit with the widely used software matlab / simulink. the displacement of the rod piston and the impact of hydraulic are analyzed in the different input flow ( frequency of pump ) and different reversing time. it found out the cause of hydraulic impact ( one - to - one incorrespondence between the response time of dividing circuit and the operation time of rod piston ), and gave some methods to weaken hydraulic impact. in the final part of the paper, the reliability of the theory analysis is further verified by the experiment of hydraulic system

    首先在流變學原理的基礎上，深入分析混凝土在輸送管道內的流動狀態，得出混凝土泵的負載特性方程；然後根據功率鍵合圖的建模方法，建立泵送迴路和分配迴路的數學模型，並運用模擬軟體matlab simulink對泵送和分配迴路模型進行了模擬，分析了在不同的輸入流量（泵送頻率）和換向時間下，活塞桿的位移和系統的液壓沖擊情況，找到了引起液壓沖擊的根本原因（即分配迴路的響應時間（固定值）與活塞桿的運動時間（變化值）不相匹配） ，並提出了相應的改進方法。
  2. 3 > the power - load matching control of pump and diesel is also investigated in this paper, which includes economic working control and load limit control of diesel

    3 、對液壓泵與柴油機之間的功率匹配控制進行了研究，其中包括柴油機經濟工作點的控制和防止柴油機過載的全程極限負荷控制。
  3. Using its two characteristics - fully automatic and rapid, this system can accomplish simultaneous, rapid, stable and repeatable matching with the load impedance, especially the dynamic load impedance ( eg : plasma load ). at the same time, it maintains the reflection coefficient at the desired value ( eg : 1. 2 ) to assure that the microwave transmission is at its best

    此系統可利用它全自動化和快速的特點，實時的為負載尤其是動態負載（比如:等離子體負載）提供快速，穩定，可重復的匹配，自動將反射系數保持到工程理想值，從而實現微波功率的最佳傳輸。
  4. The ic modulation circuits and microprocessor are used in the control unit. on the side of input of inverter, the maximum power point tracking of solar module is well realized by using a kind of thought of self - optimizing control ; on the side of output of the inverter, a kind of approximate optimum v / f control strategy is used in order to optimize the match between the output of the inverter and load of motor - pump

    在逆變器輸入側，採用自尋優控制思想實現太陽能電池最大功率點跟蹤（ mppt ） ；在輸出側，採用了v / f近似優化的控制策略，以優化逆變器輸出與機泵負載之間的匹配。
  5. Finally, the design and the test experiment of a high power matching load are introduced. the load has a steady resistance of 5. 82

    最後，介紹了實驗中設計並研製的大功率低電感匹配負載，該負載冷測電阻值5 . 82
  6. In this paper, it introduces an automatic impedance matching system that can accomplish matching with the dynamic load impedance in highpower microwave system

    本文構建了一個能為大功率微波系統的動態負載提供匹配的自動阻抗匹配系統。
  7. Load conduct power integration andproportional control of the hydraulic system

    液壓系統負載傳感功率匹配與比例控制研究
  8. After you make sured the loudspeaker, will choose the enlarger, then make can with accuracy start this this loudspeaker. not only the enlarger s power want enough and big, but also the enlarger s electric voltage the electric current characteristic must also load the with loudspeaker to match. 100 w powers lose into the enlarger that a loudspeaker ambition for 8 ws need that enlarger, with 100 it is same that w powers lose into a loudspeaker for 2 ws

    當你確定了揚聲器之後，就要選擇放大器，以使能正確地啟動這此揚聲器。不僅放大器的功率要足夠大，而且放大器的電壓電流v - 1特性也必須與揚聲器負載相匹配。 100w功率輸進一個8w的揚聲器志需要的放大器，與100w功率輸進一個2w的揚聲器的放大器是相同的。
分享友人
分享到 Line

分享到臉書