噴嘴體 的英文怎麼說
中文拼音 [pēnzuǐtǐ]
噴嘴體
英文
nozzle body-
This paper deriving the theory work inflection point in the static stage characteristics curve of small measurement range linear dimension measurement. by the way of high pressure and back pressure pneumatic measure and designed the parameter of the mainly and measure spray head, which are the key component in the spray head - baffle pneumatic sensor. the different groups for the main - spray head and the measure spray head, will effect the dynamic and static stage characteristic parameter. the author have done contrast experiment and optimization design to test and verify the theory derivation whereby made the rang of show valve of pneumatic measure system measure range up to 40 u m, the sensitivity up to 100mv / u m, resolution up to 0. 05 p m, the uncertainly of measure is less than 0. o2 u m, satisfaction of requirement of groups the carboy hatch thickness size precise measure of soft shims
對高壓背壓式氣動測量用於小量程線性尺寸測量的靜態特性曲線的理論工作拐點進行了推導，對氣動測量系統中的噴嘴-擋板型氣動傳感器中的關鍵部件? ?主噴嘴和測量噴嘴的參數進行了理論設計，對主噴嘴和測量噴嘴的不同組合，將影響測量系統靜、動態特性指標的噴嘴參數進行了對比實驗和優化設計，並通過實驗驗證了理論推導，從而使氣動測量系統量程的示值范圍達到40 m ，靈敏度達到100mv m ，解析度達到0 . 05 m ，測量不確定度小於0 . 2 m ，滿足了壓縮機缸蓋軟體墊片厚度尺寸精密測量分組的要求。As to the work about theory analysis, at first, the paper describes the atomizing and humidifying process of the centrifugal nozzle with firing pin type, high pressure and little aperture and liquid physical properties. later, combining with the structure characters of this kind of nozzle, the paper studies on the theory of the atomizing and humidifying process by three phases, which is water film forming phase, water film falling into pieces phase, and heat and mass transfer between water and air phase in turn
理論工作方面，首先描述了撞針型高壓小孔徑離心式噴嘴的霧化加濕過程和液體的物理性質，然後結合撞針型高壓小孔徑離心式噴嘴的結構特點，將其霧化加濕過程分三個階段進行機理上的研究，這三個階段依次為液膜形成、液膜初次破碎及二次霧化、水與空氣的熱濕交換。Through the special studies on impacts to atomizing and humidifying effect from such factors as the firing pin type, centrifugal structure, higher spraying pressure, less aperture, initial water temperature and original state of the air, some conclusions are obtained, such as : the centrifugal nozzle with firing pin type, high pressure and little aperture has bigger air eddy and atomizing angle. the spaying liquid has high velocity. the droplet is small, and the heat and mass transfer velocity is high
通過對撞針型結構、離心式結構、較高的噴水壓力、較小的噴嘴孔徑、噴水初溫及待加濕空氣初狀態對霧化加濕效果的作用原理的重點分析，得到：撞針型高壓小孔徑離心式噴嘴具有較大的空氣渦與霧化角，噴出的液體流速高、液滴小、水與空氣傳熱傳質速率高，撞針型結構提高了霧化加濕效率，高壓小孔徑的特點為霧化加濕提供了較大的能量，而噴水初溫的升高會減小水的粘性力和表面張力，從而優化加濕效果。Therefore the output magnetic torque of torque motor can be increased. in this paper, mathematical model of hydraulic flapper - nozzle servo - valve is introduced. the mathematical model of magnetic fluid is built according to the reference introduction
本文給出了噴嘴擋板伺服閥的數學模型，對作用於伺服閥力矩馬達的磁流體數學模型進行了推導，給出了添加磁流體的噴嘴擋板伺服閥的數學模型。Ultrasonic has being attracted much attention gradually in fuel atomization because of some specialities of cavitation and infection on liquid flow. in the course of atomization of pitchy oil, especially, does it show greatly its advantage, but its material atomizational mechanism need research ulteriorly. the primary content of this thesis is about adding cantilever reed to effervescent atomizer so as to combine ultrasonic and effervescent. this thesis has discussed ultrasonic some mechanism, ultrasonic dynamical procreator, effervescent and liquid mucosity infection on atomization, at the some time we make some experiments and discuss atomization rule following some machinery parameter and run parameter so as to find some rule about ultrasonic atomization and to rich the research of ultrasonic atomization mechanism. all that will be beneficial to the design about ultrasonic atomization atomizer
超聲波由於其空化機理及對液體的流變性影響等特性，在燃油霧化燃燒中逐步引起人們的重視，尤其在重渣油等高粘度液體的霧化過程中逐步顯示出其優越性，但其具體的霧化機理還需要做進一步的研究在氣泡霧化噴嘴基礎加入懸臂式簧片哨，將超聲波與氣泡霧化相結合是本文討論的主要內容本文從研究超聲波的一些機理入手，討論了超聲動力發生器氣泡霧化以及液體粘度對霧化質量的影響，並通過具體的實驗，根據實驗數據來討論霧化質量隨各種結構參數運行參數的變化規律，以便找到超聲霧化的一些規律，豐富對超聲霧化機理的研究，對超聲霧化噴嘴的設計具有一定的指導意義。Strong and high effective mixing of swzzero gravity particle mixer can meet your demand. two mixing axles make a equal speed and reverse rotation in horizontal tube. oars on mixing axle make the materials do radial motion, circular motion and axial motion. in a short time, the particle can be stirred homoginously. nozzel on cover of tube can be used when the solid is mixed with liquid
無重力粒子混合機（以下簡稱無重力）以強烈、高效混合而來滿足用戶需求，臥式筒體內兩根攪拌軸等速反向旋轉，攪拌軸等速反旋轉，攪攔軸上特殊布置的漿葉確保物料徑向、環向、軸向三向運動，形成復合循環，在極短的時間內達到均勻混合，筒蓋上布置霧化噴嘴供你固液混合時使用。According to rigorous procedures, an experimental study was carried out to investigate the effects of jet exit velocity, flow direction, fluid subcooling and nozzle diameter on hysteresis of boiling heat transfer with impinging circular submerged jets of highly - wetting liquids
摘要系統地研究了液體在圓形斷面噴嘴浸沒射流作用下沸騰熱滯后與射流沖擊速度大小、液體流動方向、液體過冷度和噴嘴直徑等因素的影響。Measurement of gas flow by means of critical flow venturi nozzles
用臨界流量文丘里噴嘴測定氣體流量Gas flow by means of critical flow venturi nozzles, measurement of
利用臨界文氏流量噴嘴測量氣體流量The experimental results showed that the maximum pressure drop and the operational pressure drop were related with particles diameter, bed height and superficial velocity, and the latter was also related with bed structure
實驗表明：雙噴嘴矩形噴動床的最大噴動壓降和操作壓降與顆粒粒徑、床層高度及表觀氣速有關，而操作壓降還與床體結構有關。A reasonable position of driving nozzle helps to achieve the maximum material flow that also depends on other parameters such as backpressure, properties of conveyed material and driving gas. it is observed that, an increase of convergent section angle is harmful to the pneumatic conveying system, and also influences on the mass flow rate of conveyed material, the distribution of static pressures in injector and the pressure drops of conveying pipe. in addition, within a reasonable scope of air mass rate, increasing the driving jet velocity is more advantageous than enlarging the dimension of driving nozzle
試驗研究發現，氣體噴嘴位置對氣固噴射器的輸送能力影響最大，氣體噴嘴存在某一最佳位置，而這一最佳位置與背壓、輸送物料特性和輸送風特性相關聯；氣固噴射器的收縮角對其輸送能力、內部靜壓分佈和輸送管阻力特性均有適量影響，收縮角增大對整個輸送系統均不利；在適當的輸送風范圍內，提高氣體噴嘴出口速度比擴大氣體噴嘴尺寸更為有利，但氣體噴嘴出口速度過高會增加氣固噴射器和輸送管內的能量損耗，給輸送帶來不利的影響；系統背壓與氣固噴射器的氣體噴嘴出口速度的選取有關。Measurement of fluid flow by means of pressure differential devices inserted in circular cross - section conduits running full - nozzles and venturi nozzles
用插入圓截面管道中的壓差裝置測量流體流量.噴嘴和文杜利噴嘴Measurement of fluid flow by means of pressure differential devices - guidelines for specification of nozzles and orifice plates beyond the scope of iso 5167 - 1
用壓差裝置測量流體流量. iso 5167 - 1規定范圍之外的噴嘴和節流孔板規范指南Through the controls of geometric dimension of micro - nozzle and driving frequency to obtain the volume of droplets in the grade of pico to femto litre, which is applicable to make high density micro - array
通過微噴嘴幾何尺寸控制和驅動頻率控制獲得從飛升到皮升級樣點體積，可以用於製作高密度的微陣列。Low frequency micro - vibration causes the micro - fluid to produce uniform dispersion and injection which carried out a hydrophobization treatment on the inner wall of micro - nozzle, thus eliminated the spontaneous flowing of micro - fluid inside the micro - nozzle due to wet ting effect so as to let the micro - injection be provided with a digitalized and volume controllable character
壓電陶瓷低頻微振動使得微流體產生均勻的離散和噴射；對微噴嘴內壁進行疏水化處理，從而消除微流體由於濕潤作用在微噴嘴內部的自發性流動，使得微噴射具有數字化量可控的特徵。Petroleum and related products - determination of spray ignition characteristics of fire - resistant fluids - spray flame persistence - hollow - cone nozzle method
石油和相關產品.耐火液體噴射點燃特性的測定.噴射火焰持久性.空心錐形噴嘴法Petroleum and related products - determination of spray ignition characteristics of fire - resistant fluids - part 1 : spray flame persistence - hollow - cone nozzle method
石油和相關產品.耐火液體噴射點火特性的測定.第1部分:噴射火焰持久性.空心錐噴嘴法Based on the induction phenomenon caused in gas hydrate formation, the influential rules of its gas entrance mode, temperature, pressure, water resources and nozzle on the induction time are analyzed by means of experimental study on the induction time of gas hydrate formation obtained by water spray and enhancement
摘要以氣體水合物形成過程中的誘導現象為基礎，通過對噴霧強化方式制取天然氣水合物的誘導時間進行試驗研究，考察分析了系統進氣方式、溫度、壓力、水源及噴嘴等因素對誘導時間的影響規律。Quantitatively analyses the concrete influences on atomizing humidifying performance of the nozzle aperture, initial temperature and the pressure of spray water and the water - air ratio through a single factor experiment
通過單因素試驗定量分析了噴嘴孔徑、噴水初溫、噴水壓力以及水氣比對霧化加濕的具體影響。Road vehicles - shapes and dimensions of fuel injection nozzle holders for diesel engines - size " p
道路車輛.柴油機燃油噴嘴體的形狀和尺寸.規格p分享友人