嚙合條件 的英文怎麼說

中文拼音 [niègětiáojiàn]
嚙合條件 英文
meshing condition
  • 嚙 : 動詞[書面語]1. （鼠、兔等用牙啃或咬） gnaw （at） 2. （侵蝕） erode
  • 合 : 合量詞（容量單位） ge, a unit of dry measure for grain （=1 decilitre）
  • 條 : Ⅰ名詞1 （細長的樹枝） twig 2 （條子） slip; strip 3 （分項目的） item; article 4 （層次; 秩序; 條...
  • 件 : Ⅰ量詞（用於個體事物） piece; article; item Ⅱ名詞1. （指可以一一計算的事物） 2. （文件） letter; correspondence; paper; document
  • 條件 : 1. （客觀的因素） condition; term; factor 2. （提出的要求） requirement; prerequisite; qualification
  1. On the basis of the engage efficiency and lubricious conditions, theoretical transmission efficiency with the different drive ratios ( 1 / 50 and 6 / 31 ) of involute cylinder worm gears is analyzed. at the same time, the change trend of engage efficiency and transmission efficiency with different design parameters is discussed. the experimental investigation on transmission efficiency

    從漸開線蝸輪蝸桿傳動的嚙合效率和潤滑條件兩個方面對不同傳動比的漸開線圓柱蝸桿的傳動效率進行理論分析，並通過傳動比分別為1 / 50和6 / 31的漸開線圓柱蝸桿設計參數得到蝸桿潤滑條件的理論分析結果和蝸桿嚙合效率、傳動效率的變化趨勢，同時利用電測法對蝸桿傳動的傳動效率、潤滑油平衡溫度進行測試，將測試數據與理論計算結果進行對比分析，得出理論分析結果的正確性。
  2. On the condition of “ many - head ” and “ small drive ratio ” ， the plane double enveloping hourglass worm can not settle the problem of undercutting and sharpening simultaneously. it has devoted to a new type hourglass worm _ sphere double enveloping hourglass worm. the coordinate system is established according to the frock. the meshing equation and the tooth equation of worm and gear have been developed and the distribution of contact line on gear tooth is analyzed. to evaluate the meshing quality ， four meshing quality indexes and five original parameters are put forward. through mass programming computing ， the relations between meshing quality and original parameters are derived and depicted by graphs

    考慮到平面二次包絡環面蝸桿傳動在多頭小傳動比條件下根切與齒頂變尖的矛盾很難同時解決且嚙合性能較差，介紹了一種新型環面蝸桿傳動? ?球面二次包絡環面蝸桿傳動.在研究過程中，根據工裝建立了坐標系，根據一二包過程的運動關系推得了嚙合方程和蝸桿與蝸輪的齒面方程，分析了蝸輪齒面上的接觸線分佈.為了評價嚙合性能，提出了4項性能指標和5項原始參數，通過大量編程計算得到了嚙合性能指標與原始參數之間的關系，並以圖表直觀的表示
  3. ( 3 ) in the condition of invariable instantaneous speed ratio, the equations of teeth surface of all key components, such as end face gear, oscillating teeth, wave producer, et al, are deduced

    （ 3 ）在保證瞬時傳動比恆定的條件下，由空間嚙合原理出發，重點推導了活齒端面諧波齒輪傳動裝置的主要傳動部件? ?端面齒輪、活齒以及波發生器端面凸輪的齒面方程。
  4. As both the meshing point and ball ' s center are on the given cylinder, a general method for developing the cam ' s profile is studied. it is proved that the profile of positive and negative transmission is unique if the face gear, the difference between face tooth number and ball number and the diameter of ball are the same. the concrete expression of meshing cam on given spatial cycloid profile, and the characteristics of the profiles are discussed

    論文的主要工作包括： 1 、根據嚙合點和鋼球中心軌跡均在同一圓柱面上的特點，研究了給定端齒齒廓條件下求解凸輪齒廓的一般方法；論證了在給定端齒、齒差數和鋼球直徑相同的條件下，正負齒差嚙合齒廓的唯一性；討論了端齒為球面擺線時，凸輪齒廓的具體表達式，並研究了該齒廓的性質。
  5. 2. the flux characteristics of ordinary helical gear pump are lucubrated by theory for the first time, on this condition the selective qualification of the helical gear pump is gained

    首次對普通斜齒齒輪泵流量特性進行了深入的理論研究，在此基礎上研究了全齒廓嚙合斜齒齒輪泵流量特性，首次得到了完全消除斜齒齒輪泵流量脈動的螺旋角的選擇條件。
  6. Equations of mesh, shorting contact line, undercutting limit line, meshing limit lines and the existence conditions, angle between the direction of relative speed and the direction of contact line, induced normal curvature about every point on the contact line are established. moreover, the paper also theoretically analyzed the error of the grinded gear surface. on the basis of the theory, the computer program is worked out to automatically produce the contact line and the boundary curves of mesh. analysis of meshing circs under different parameters can be done so that we can gain the best process condition

    首先對漸開面二次包絡理論進行了深入的探討，推導出了兩次嚙合的嚙合方程式、瞬時接觸線方程式、根切界限線方程式、嚙合界限線的方程式及其存在條件，相對運動速度方向與接觸線方向的夾角及接觸線上各點的誘導法曲率；此外，還對磨齒后工件的齒面誤差進行了理論分析；並在理論基礎上編制了相應的計算機程序，自動生成接觸線族及嚙合界限線，對不同參數條件下的嚙合情況進行分析，可以使工藝條件達到最佳狀態；最後研究了磨齒裝置，設計了磨齒機的傳動系統。
  7. Although the flux per revolution of the optimized pumps is a little smaller than that of tatsuno combined pumps, other characteristics, such as fluctuation rate, maximum pressure angle and velocity fluctuation rate etc, are much better. the methods to cut gears are proposed in the theory for the practical produce in the future

    雖然，在體積相等的條件下，優化出來的外圓弧包絡線內嚙合齒輪泵的排量略小於tatsuno組合泵的排量，但其它性能（如：流量脈動率、最大壓力角、速度波動量）都更優。
  8. Through systemic analyzing on spiral helical gear transmission with different basic parameters, the essay found out rules of how can such basic parameters influence spiral helical gear engagement characteristics. so it brings forward the auxiliary assembling mode of adopting one straight gear and one helical gear on condition of little axial angle as well as treasures to ameliorate ill engagement performance on condition of large axial angle, another two jobs of the essay are to clarify the wrong concept that spiral helical gear can only transmit movement but not impetus and to provide a brief and practical method of analyzing contact for gear pairs whose surface equations can be written out directly

    通過對不同基本參數的螺旋齒輪傳動進行系統研究，找出了螺旋齒輪基本參數對其嚙合特性的影響規律，提出小軸交角條件下可採用一直齒輪、一斜齒輪的齒輪副組合方式，給出了大軸交角條件下嚙合性能不良的改進措施。澄清了螺旋齒輪只能傳遞運動不能傳遞動力的誤區，為能夠直接寫出齒面方程的齒輪副進行齒面接觸分析提供了一種簡便、實用的新方法。
  9. Based on the theories of gear engagement, contact analysis, friction and heat transfer, a three - dimensional finite element model of gear tooth was established to investigate temperature distributions and variations along the contact path over a range of applied loads and operating speeds with consideration of lubrication conditions. sensitivity analysis of surface temperature to gear configuration, frictional heat flux, heat transfer coefficients, and oil and ambient temperature was conducted and the major parameters influencing surface temperature were evaluated

    本文基於齒輪嚙合原理、輪齒接觸分析、摩擦學和傳熱學，以有限元分析方法和理論分析計算相結合為手段並以實驗測量結果作為參考，建立了適用於工業應用並具有較高計算精度的高速齒輪傳動輪齒溫度分析的模型和方法，系統地分析了輪齒本體溫度的大小和分佈以及齒輪幾何、載荷及轉速和潤滑冷卻條件等對輪齒本體溫度的影響。
  10. In this paper, we designed the structure of the gear and rack in this actuating mechanism, elaborated the theory of its formation, and deduced the profile function and gearing function of the gear and rack. furthermore, we deduced the inherent radius of going around a turn under certain circumstance, the condition of the correct gearing and the continuous transmission. in order to make the mechanism move steady, we designed the derivation mechanism and manufacture the modle

    本文對該傳動機構中的漸開線柱齒鼓形齒輪和空間齒條的結構進行了設計，並給出了齒輪和齒條的成型原理，推導出了漸開線柱齒鼓形齒輪和空間齒條的齒廓參數方程、嚙合方程;進一步分析並確定了漸開線柱齒鼓形齒輪、空間齒條在給定嚙合傳動條件下所能實現的固有轉彎半徑和運動約束條件，並對其側隙及效率進行了計算和分析。
  11. At first the paper begin to study the foundation of digital curved face and space meshing principle, introduce the basic knowledge of curve theory and curved face theory, explain the mathematical tools of vector turning and coordinate conversion in the paper ; analyse the motion and relative motion of rigid body, provide the condition of gear driving continuous contact and equation of conjugate meshing

    論文首先從參數化曲面和空間嚙合原理基礎出發，介紹了曲線論和曲面論的基本知識，對課題研究重的數學工具矢量回轉和坐標變換進行了說明;分析了剛體的運動和相對運動，根據空間嚙合原理給出了輪齒傳動連續接觸的條件和共軛條件方程。
  12. The results of the studies show that, when fine medium belt, proper load and velocity are selected, the transmission performance of gear with meshed medium belt is superior to invloute gear ' s ; furthermore, it can be lubricated with water, and it ' s effects are almost fine to the lubricant effects with oil. so we can realize a " green lubrication " type of gear transmission

    試驗結果表明：選擇適當的介質帶材料和一定的載荷速度條件，帶式嚙合介質齒輪的傳動性能優于漸開線齒輪，並可用水進行潤滑，幾乎達到在油潤滑條件下的效果，實現一種節能、無污染的綠色潤滑齒輪傳動；相對于漸開線齒輪，帶式嚙合介質齒輪具有顯著的減振降噪作用，動態特性優越。
  13. By analyzing the vibration movement of the gear system, the actual center - line equation and that of the theoretic meshing line were derived in their vibration condition, and their movements and the modality of the actual meshing line was analytically verified

    摘要根據齒輪系統的振動運動，建立了在振動條件下齒輪副實際中心線方程和理論嚙合線方程，分析論證了實際中心線和理論嚙合線的運動及實際嚙合線的形態。
  14. The judgment condition for the involute gear pairwith fewer teeth number outside pitch point

    少齒數漸開線齒輪節點外嚙合的判定條件
  15. The two key factors, machining methods and machine - setting parameters of sbg, which are related with the generation of theoretical tooth surface and topographic deviation for sbg, are analyzed in details. after building the machine - tool mathematical model and computing the tooth surface parameters, using the given conditions and mesh equation, the coordinates of the theoretical tooth surface of sbg can be computed, and, then, the theoretical tooth surface model of sbg is derived

    本文詳細地分析了形成螺旋錐齒輪理論齒面及產生拓撲誤差的兩個關鍵因素，即螺旋錐齒輪的切齒加工方法和機床調整參數;通過建立機床數學模型，計算齒面參數，用已知條件和嚙合方程進行聯合求解，得出了理論齒面的坐標值，從而獲得了螺旋錐齒輪的理論齒面模型。
  16. Firstly, the paper introduces the development and application of computer graphics & image technique, discusses the principle and method of cg and digital image processing, such as matrix of the graphic transformation, homogeneous reference frame, sampling and quantization of the image, file format of the image, template operation, etc. secondly the paper introduces the purpose and method of image enhancement processing, explains the each occasion of those methods such as threshold transformation, smoothing processing, sharpening processing, analyzes and contrasts the processing results of object image. thirdly, the paper introduces the method of mathematics morphologic, edge detection and thinning processing, attains character description of image and character dots of the contour. fourthly, the paper processes the coordinate transformation to character dots and basic splines fitting, imports correlative condition to devise meshing line and meshing track

    本文首先介紹了計算機圖形圖像技術的發展與應用情況，對計算機圖形學和數字圖像處理的一些基本理論和方法如圖形變換矩陣、齊次坐標系、圖像采樣和量化、圖像文件格式、模板操作等內容進行了討論：然後對圖像增強處理的目的和方法進行了介紹，對諸如閥值變換、平滑處理、銳化處理等方法的應用場合進行了說明，並對實物圖像的處理結果進行了分析與比較；接下來介紹了數學形態學方法、對增強后的圖像進行邊緣檢測的方法和圖像的特徵描述方法，並獲取輪廓的特徵點：隨后對獲取的特徵點進行坐標變換，並進行b樣條曲線擬合，引入相關條件生成齒輪副的嚙合線及嚙合軌跡：最後引入等值線和區域填充表示方法，並以等值線和區域填充的形式對弧齒錐齒輪嚙合模擬的載荷分佈情況進行了直觀的表示。
  17. The curvature interference of the gear and the influence of radius of the mill - cutter, axial misalignment, and center distance on meshing are analyzed. based on these analyses, propose two methods to achieve point - contact : to change the radius of the mill - cutter and increase the center distance

    在分析了弧齒線圓柱齒輪的嚙合傳動不產生曲率干涉的條件和刀盤展成半徑、軸線平行度誤差、中心距對嚙合影響的基礎上，提出了點接觸弧齒線圓柱齒輪實現的兩種方案:調整刀盤展成半徑和增大中心距。
  18. This paper presents operation principle of gear dynamic engagement system and points out shifting conditions according to geometry, kinematics and kinetics theories

    摘要介紹了齒輪動態嚙合系統及其工作原理，從幾何學、運動學、動力學3方面分析了安全換擋的要求，綜合指出了允許換擋的條件。
  19. In a word, the paper provides an visible software operation platform for the analysis and design of globoidal indexing cam, builds primary model of the mechanism dynamics system, then provides references for the mechanism ' s deep research

    最後對弧面分度凸輪機構動力學系統的主要特徵進行了分析，並建立考慮構件慣性，嚙合剛度及參數激勵的條件下的弧面分度凸輪機構的振動分析模型。
  20. So this paper bring forward several new concepts and new terms, and give the whole defmations to their physical meanings ; advance the conditions of right gearing mesh and continuous drive ; prove out that a pair of ring involute tooth forms are conjugated and that they can achieve precise spherical motion of constant transmitting ratio employing the space mesh theory

    為此，本文首次提出了球齒輪傳動中若干新概念，新名詞，並對物理含義作了完整的定義；提出了球齒輪機構的正確嚙合條件和連續傳動條件；利用空間嚙合理論，證明了一對漸開線環形齒廓互為共軛齒廓，能實現精確的定傳動比球面運動。
分享友人
分享到 Line

分享到臉書