嚙合角 的英文怎麼說

中文拼音 [niègějiǎo]
嚙合角 英文
angle of engagement
  • 嚙 : 動詞[書面語]1. （鼠、兔等用牙啃或咬） gnaw （at） 2. （侵蝕） erode
  • 合 : 合量詞（容量單位） ge, a unit of dry measure for grain （=1 decilitre）
  • 角 : 角Ⅰ名詞1 （牛、羊、 鹿等頭上長出的堅硬的東西） horn 2 （古時軍中吹的樂器） bugle; horn 3 （形狀像...
  1. The paper studies the surface geometry of globoidal indexing cam by applying the theory of conjugate surfaces and the method of coordinate transformation, presents the equations related to the main inducement curvature of the cam profiles, analysis and deduces the equations of two circumscription curves, which judge if the conjugate surface could mesh properly. some calculate examples and conclusion are given. the surface equation of the globoidal cam and conjugate equation are established

    論文首先在分析空間嚙合原理基礎上，採用坐標變換法推導出弧面分度凸輪的工作廓面方程、嚙合方程和壓力角計算公式，對弧面分度凸輪的嚙合特性進行了深入的分析和研究，對判斷曲面能否正確嚙合的依據如兩類界限線方程以及誘導主曲率等進行推導，並給出算例。
  2. We have in - house rolling, forging and machining capability to manufacture all types of fishplates including plain, joggled, angle, and combination fishplate to various drawings for various rails

    我們有內部的軋輥，鍛造和機床加工這樣的技術，有能力去生產所有類型的魚尾板包括普通魚尾板，嚙合型魚尾板，角形魚尾板和組合型魚尾板根據各種各樣的圖紙為各種各樣的鐵路。
  3. Size and obliquity of tooth directly influence clutch whether normal operating. it is a key part for ensuring normal operating of aira too. this article fully deduces their compute formula

    該齒形的大小、傾角直接影響離合器是否能正確地嚙合和分離，也是保證機構進行正確工作的關鍵部分，本文詳盡推導了它們的計算公式。
  4. These designing parameters include stiffness of epicyclical bearings, synthetic meshing stiffness of gears, stiffness of supporting bearing of out put shaft, mass of inner rack, meshing angle of gears, distance between inputting shaft and supporting shaft and input speed etc. according to these analyses, the possible way for improving the dynamic function of three - ring transmission may be put forward

    這些設計參數包括：行星軸承剛度、齒輪綜合嚙合剛度、輸出軸支承軸承剛度、內齒板質量、齒輪嚙合角、輸入軸和支承軸間距及輸入轉速等，根據這些分析，可以提出改善三環傳動動態性能的可能途徑。
  5. By analyzing phase angle of meshing geometric drawing position, the theoretical formula of cycloid gear actual operating space of cycloid planetary gear speed reducer is driven, at the same time, fitting a curve, and discussing engineering significance of function curve to combine reality

    摘要通過分析嚙合相位角幾何圖形的位置，推導出擺線針輪行星減速器中擺線輪實際工作范圍的理論公式，畫出了嚙合相位角函數的擬合曲線，並結合實際討論其函數曲線的工程意義。
  6. An automated de - noising algorithm based on the energy of wavelet packet not donoho ' s threshold algorithm is established. a gear feature vibration signal extraction method using the wavelet packet energy is proposed, which can separate gear meshing vibration, noise vibration and gear fault vibration signal from the original gearbox case vibration signal. basis pursuit ( bp ) algorithm is introduced into the filed of mechanical signal de - noising and feature extraction for the first time

    第三章擺脫了donoho的閾值消噪思想，從能量的角度建立了基於小波包的自動消噪演算法；提出基於小波包能量分佈的齒輪故障特徵信號提取方法，可以將齒輪嚙合振動信號、干擾振動信號以及故障沖擊振動信號從原始齒輪振動信號中分離出來；首次將基追蹤消噪演算法引入到機械故障信號的消噪與特徵提取上，通過對齒輪故障信號的消噪，表明了它的有效性，並對影響該方法實際應用效果的因素進行了全面的分析，同時也指出了該方法存在的局限性。
  7. 2. the flux characteristics of ordinary helical gear pump are lucubrated by theory for the first time, on this condition the selective qualification of the helical gear pump is gained

    首次對普通斜齒齒輪泵流量特性進行了深入的理論研究，在此基礎上研究了全齒廓嚙合斜齒齒輪泵流量特性，首次得到了完全消除斜齒齒輪泵流量脈動的螺旋角的選擇條件。
  8. On the condition the trapping characteristics of whole profile meshing helical pump are lucubrated by theory for the first time, and the select range of the helical angle that can eliminate completely the trapping of whole profile meshing helical gear pump is also obtained

    在此基礎上，首次對全齒廓嚙合斜齒齒輪泵的困油特性進行了詳細的理論研究，得到了完全消除全齒廓嚙合斜齒齒輪泵困油沖擊的螺旋角的選擇范圍。
  9. Equations of mesh, shorting contact line, undercutting limit line, meshing limit lines and the existence conditions, angle between the direction of relative speed and the direction of contact line, induced normal curvature about every point on the contact line are established. moreover, the paper also theoretically analyzed the error of the grinded gear surface. on the basis of the theory, the computer program is worked out to automatically produce the contact line and the boundary curves of mesh. analysis of meshing circs under different parameters can be done so that we can gain the best process condition

    首先對漸開面二次包絡理論進行了深入的探討，推導出了兩次嚙合的嚙合方程式、瞬時接觸線方程式、根切界限線方程式、嚙合界限線的方程式及其存在條件，相對運動速度方向與接觸線方向的夾角及接觸線上各點的誘導法曲率；此外，還對磨齒后工件的齒面誤差進行了理論分析；並在理論基礎上編制了相應的計算機程序，自動生成接觸線族及嚙合界限線，對不同參數條件下的嚙合情況進行分析，可以使工藝條件達到最佳狀態；最後研究了磨齒裝置，設計了磨齒機的傳動系統。
  10. Tooth surface equations and contact line equations of the involute worm gearing are established according to its machining methodology. meshing characteristics in rigidity condition are studied. these characters include the inductive normal curvature along the contact line on the worm surface, the first and the second limit lines during the engage of the worm gear, and the influence of the intersect angle between the contact line the relative velocity of the worm and the gear on transmission performance

    根據漸開線圓柱蝸桿傳動的創成方法，建立了漸開線圓柱蝸桿和蝸輪的接觸線方程式、齒面方程式，分析了漸開線圓柱蝸桿傳動的剛性嚙合特性，如蝸桿與蝸輪嚙合時的誘導法曲率、一類界限曲線、二類界限曲線和蝸桿與蝸輪間相對速度方向和接觸線方向的夾角對傳動性能的影響； 2
  11. Although the flux per revolution of the optimized pumps is a little smaller than that of tatsuno combined pumps, other characteristics, such as fluctuation rate, maximum pressure angle and velocity fluctuation rate etc, are much better. the methods to cut gears are proposed in the theory for the practical produce in the future

    雖然，在體積相等的條件下，優化出來的外圓弧包絡線內嚙合齒輪泵的排量略小於tatsuno組合泵的排量，但其它性能（如：流量脈動率、最大壓力角、速度波動量）都更優。
  12. Through systemic analyzing on spiral helical gear transmission with different basic parameters, the essay found out rules of how can such basic parameters influence spiral helical gear engagement characteristics. so it brings forward the auxiliary assembling mode of adopting one straight gear and one helical gear on condition of little axial angle as well as treasures to ameliorate ill engagement performance on condition of large axial angle, another two jobs of the essay are to clarify the wrong concept that spiral helical gear can only transmit movement but not impetus and to provide a brief and practical method of analyzing contact for gear pairs whose surface equations can be written out directly

    通過對不同基本參數的螺旋齒輪傳動進行系統研究，找出了螺旋齒輪基本參數對其嚙合特性的影響規律，提出小軸交角條件下可採用一直齒輪、一斜齒輪的齒輪副組合方式，給出了大軸交角條件下嚙合性能不良的改進措施。澄清了螺旋齒輪只能傳遞運動不能傳遞動力的誤區，為能夠直接寫出齒面方程的齒輪副進行齒面接觸分析提供了一種簡便、實用的新方法。
  13. Helix angles for cylindrical gear teeth

    圓柱齒輪嚙合的螺旋角
  14. From the aspect of geometry, structure design, manufacture and examine, this paper generally summarizes the gcm ' s study progress in detail, discusses its kinetic rule and the determination of its primary structure parameter, and educes its surface equation and pressure angle equation based on the homogeneous matrix transformation and the conjugate engagement theory of spatial surface. on the basis of geometry study of gcm, the paper makes a comprehensive analysis to the interference phenomenon that will possible exist in the assemble course of two different structure of gcm with the help of matlab software

    本文從運動幾何學、結構設計、動力學、製造和檢測等方面對國內外弧面凸輪機構的研究進展進行了全面綜述，詳細論述了高速凸輪機構的運動規律和弧面凸輪機構基本尺寸的確定，基於空間曲面共軛嚙合原理，通過齊次變換推導了外弧面凸輪的曲面方程和壓力角方程，並提出了對應的廓面修形演算法；提出了內弧面凸輪機構的構想，推導了內弧面凸輪的曲面方程和壓力角方程。
  15. The critical error has been found through computation, which is the error circling the gear. the load sharing characteristics of two kind of star - type gearing train has been determined through comparison. based on computation, the load sharing capability of two - stage external gear train is better than that of two - stage internal and external gear train

    其次，從靜力學的角度分析了各誤差對系統均載性能的影響，比較了各誤差對系統均載性能影響的大小，得到了較大的影響系統均載的誤差因素，即圓周方向分佈的誤差；比較了兩種星型齒輪系統的均載性能，根據計算結果，兩級外嚙合傳動系統的均載性能要好於兩級內外嚙合傳動系統。
  16. First, the basic theory of static load sharing mechanism has been presented, mainly including manufacturing and assembly error of each gear component ' s axis and each bearing ' s axis, gear size ( tooth thickness ) errors, simultaneous error of middle two - tooth. the formula of equivalent mesh error has been deduced, the load sharing coefficient has been computed. second, the influences of each error on the static load sharing coefficient have been discussed

    首先，從靜力學的角度研究了星型齒輪系統均載的基本原理；確定了影響齒輪系統均載特性的製造和安裝誤差，主要包括：各個齒輪構件的中心軸線製造和安裝誤差、軸承中心軸線的製造和安裝誤差、齒厚偏差、雙聯星輪同時嚙合線誤差；推導了這些誤差的當量嚙合誤差的計算公式，分析了系統的均載特性。
  17. Dental handpieces. part 2 : straight and geared angle handpieces

    牙科機頭.第2部分:直角和嚙合角機頭
  18. By means of analyzing the designing parameters of less tooth differenced planetary transmission mechanism with biasing crankshaft, it is pointed out that the meshing angle is a key factor which affects the transmission function of the mechanism

    摘要通過對偏曲軸少齒差行星傳動機構設計參數的分析，指出嚙合角是影響機構傳動性能的一個關鍵因素。
  19. Dental handpieces - part 2 : straight and geared angle handpieces iso 7785 - 2 : 1995 ; german version en iso 7785 - 2 : 1997

    手持式牙科器械.第2部分:平角和嚙合角手持式器械
  20. While seeking the scheme of minimum structural volume in engineering design, the optimization issue ought to be considered at the same time

    在工程設計尋求結構體積最小方案時，應同時考慮嚙合角的優化問題。
分享友人
分享到 Line

分享到臉書