圓柱蝸桿傳動 的英文怎麼說

中文拼音 [yuánzhùgǎnzhuàndòng]
圓柱蝸桿傳動 英文
single enveloping worm gear
  • 蝸 : 名詞[動物學] （蝸牛） snail
  • 桿 : 桿名詞（桿子） pole; staff
  • 傳 : 傳名詞1 （解釋經文的著作） commentaries on classics 2 （傳記） biography 3 （敘述歷史故事的作品）...
  1. Basic parameters of cylindrical worm gears

    圓柱蝸桿傳動基本參數
  2. On the basis of the engage efficiency and lubricious conditions, theoretical transmission efficiency with the different drive ratios ( 1 / 50 and 6 / 31 ) of involute cylinder worm gears is analyzed. at the same time, the change trend of engage efficiency and transmission efficiency with different design parameters is discussed. the experimental investigation on transmission efficiency

    從漸開線蝸輪蝸桿傳動的嚙合效率和潤滑條件兩個方面對不同傳動比的漸開線圓柱蝸桿的傳動效率進行理論分析，並通過傳動比分別為1 / 50和6 / 31的漸開線圓柱蝸桿設計參數得到蝸桿潤滑條件的理論分析結果和蝸桿嚙合效率、傳動效率的變化趨勢，同時利用電測法對蝸桿傳動的傳動效率、潤滑油平衡溫度進行測試，將測試數據與理論計算結果進行對比分析，得出理論分析結果的正確性。
  3. Solid model of the involute worm gearing solid model with drive ratio 1 / 50 is built by using ideas - 5. 0, then the elastic contact analysis is proceeded on the basis of contact fem. the dynamic evolution image of the area of the contact zone, the load sharing among instantaneous meshing tooth pairs, the distribution of the contact force, and tooth stress are obtained. 3

    通過漸開線圓柱蝸桿、蝸輪的齒面方程式，利用ideas - 5 . 0軟體建立了傳動比為1 / 50的漸開線圓柱蝸桿傳動的實體幾何模型，在此基礎上應用接觸有限元方法對該傳動進行了彈性接觸分析，包括接觸區的形狀、位置、載荷在瞬時嚙合齒對的分配狀況； 3
  4. The worm - drive is widely used in modern industry, especially the ordinary cylinder worm - drive in machine tool manufacturing sector. main disadvantages of worm dives are lubrication and wear problems due to relatively high sliding at the tooth contacts. the ordinary cylinder worm - drive has almost become an exclusive selection in general low speed transmission work - platform and continuous graduation mechanism

    蝸桿傳動具有傳動比大、體積小、運轉平穩、噪音小等特點，在現代工業中應用非常廣泛，在機床製造業中，普通圓柱蝸桿傳動的應用尤為普遍，並且幾乎成了一般低速傳動工作臺和連續分度機構的唯一傳動形式。
  5. Tooth surface equations and contact line equations of the involute worm gearing are established according to its machining methodology. meshing characteristics in rigidity condition are studied. these characters include the inductive normal curvature along the contact line on the worm surface, the first and the second limit lines during the engage of the worm gear, and the influence of the intersect angle between the contact line the relative velocity of the worm and the gear on transmission performance

    根據漸開線圓柱蝸桿傳動的創成方法，建立了漸開線圓柱蝸桿和蝸輪的接觸線方程式、齒面方程式，分析了漸開線圓柱蝸桿傳動的剛性嚙合特性，如蝸桿與蝸輪嚙合時的誘導法曲率、一類界限曲線、二類界限曲線和蝸桿與蝸輪間相對速度方向和接觸線方向的夾角對傳動性能的影響； 2
  6. According to the high precision and rotation stability requirement of negative scan unit of cylinder photography typesetting machine, the three levels of cylindrical gears transmission separately, the two - stage cylindrical gears - worm drive, and the worm drive was chosen through calculating its velocity ratio, the checking transmission precision, carrying on the movement precision analysis to the sweep unit, and computing overall transmission error

    摘要針對圓筒型照相排版機底片掃描裝置要求傳動精度高，轉動平穩的特點，分別選擇三級圓柱齒輪傳動，雙級圓柱齒輪蝸桿傳動，蝸桿傳動3種常見的傳動方式，計算其傳動比，驗算傳動精度，對掃描裝置進行運動精度分析，計算總體傳動誤差。
  7. Cylindrical worms ; dimensions, correlation of shaft centre distances and gear ratios of worm gear drives

    圓柱形蝸桿.尺寸軸心距和蝸輪傳動傳動比之間的關系
  8. Larger loading capacity under the same specification ; easily establishing lubricant oil film, smaller friction coefficient, higher transmission efficiency, saving energy ; highest accuracy up to grade 3 of din standard ; smoother functioning, lower noisiness and longer service life

    平麵包絡環面蝸桿與普通圓柱蝸桿傳動相比具有更大的承載能力，易於建立動壓油膜摩擦系數小，傳動效率高節省能源具有可磨削性，能達到din標準三級，面粗糙度優于ra0 . 4而且具有運行平穩噪音低壽命長等優點。
  9. The fuzzy optimal design of circular cylinder worm - drive

    圓弧齒圓柱蝸桿傳動的模糊優化設計
  10. Analysis on oylindrical worm in traction machine and modifications

    圓柱蝸桿傳動曳引機的剖析與改進
  11. Analysis of the elastohydrodynamic lubrication of arc cylindrical worm drive

    圓弧圓柱蝸桿傳動彈流潤滑分析
  12. Series of modules for gears ; modules for cylindrical worm gear transmissions

    齒輪用模數系列.第2部分:圓柱蝸桿傳動裝置的模數
  13. Fuzzy optimization of worm drive based on hybrid annealing genetic algorithm

    基於混合退火遺傳演算法的圓柱蝸桿傳動模糊優化設計
  14. Abstract : the paper suggests two methods for adjusting the mesh clearance in cylindrical worm drive : one is to adjust the meshing center distance of worm gears, the other is to use dual lead cylindrical worm, introducing briefly the principle of adjustment and making a comparison between the characteristics of the two methods

    文摘:提出了兩種調整圓柱蝸桿傳動嚙合側隙的方法:通過改變蝸輪蝸桿的嚙合中心距來改變其嚙合側隙;採用雙導程蝸桿傳動以調整蝸輪蝸桿的嚙合側隙，簡述了調整原理，並比較了兩種調整方法各自的特點。
分享友人
分享到 Line

分享到臉書