圓柱蝸桿 的英文怎麼說

中文拼音 [yuánzhùgǎn]
圓柱蝸桿 英文
cylindrical worm
  • 蝸 : 名詞[動物學] （蝸牛） snail
  • 桿 : 桿名詞（桿子） pole; staff
  1. Analysis of the axial profile of an involute helicoid worm

    漸開線圓柱蝸桿軸向齒形分析
  2. Basic parameters of cylindrical worm gears

    圓柱蝸桿傳動基本參數
  3. Terminology and symbols for cylindrical worm and worm wheel

    圓柱蝸桿蝸輪術語及代號
  4. On the basis of the engage efficiency and lubricious conditions, theoretical transmission efficiency with the different drive ratios ( 1 / 50 and 6 / 31 ) of involute cylinder worm gears is analyzed. at the same time, the change trend of engage efficiency and transmission efficiency with different design parameters is discussed. the experimental investigation on transmission efficiency

    從漸開線蝸輪蝸桿傳動的嚙合效率和潤滑條件兩個方面對不同傳動比的漸開線圓柱蝸桿的傳動效率進行理論分析，並通過傳動比分別為1 / 50和6 / 31的漸開線圓柱蝸桿設計參數得到蝸桿潤滑條件的理論分析結果和蝸桿嚙合效率、傳動效率的變化趨勢，同時利用電測法對蝸桿傳動的傳動效率、潤滑油平衡溫度進行測試，將測試數據與理論計算結果進行對比分析，得出理論分析結果的正確性。
  5. Solid model of the involute worm gearing solid model with drive ratio 1 / 50 is built by using ideas - 5. 0, then the elastic contact analysis is proceeded on the basis of contact fem. the dynamic evolution image of the area of the contact zone, the load sharing among instantaneous meshing tooth pairs, the distribution of the contact force, and tooth stress are obtained. 3

    通過漸開線圓柱蝸桿、蝸輪的齒面方程式，利用ideas - 5 . 0軟體建立了傳動比為1 / 50的漸開線圓柱蝸桿傳動的實體幾何模型，在此基礎上應用接觸有限元方法對該傳動進行了彈性接觸分析，包括接觸區的形狀、位置、載荷在瞬時嚙合齒對的分配狀況； 3
  6. The worm - drive is widely used in modern industry, especially the ordinary cylinder worm - drive in machine tool manufacturing sector. main disadvantages of worm dives are lubrication and wear problems due to relatively high sliding at the tooth contacts. the ordinary cylinder worm - drive has almost become an exclusive selection in general low speed transmission work - platform and continuous graduation mechanism

    蝸桿傳動具有傳動比大、體積小、運轉平穩、噪音小等特點，在現代工業中應用非常廣泛，在機床製造業中，普通圓柱蝸桿傳動的應用尤為普遍，並且幾乎成了一般低速傳動工作臺和連續分度機構的唯一傳動形式。
  7. Basic rack tooth profile of fine - pitch cylindrical worm

    小模數圓柱蝸桿基本齒廓
  8. Tooth surface equations and contact line equations of the involute worm gearing are established according to its machining methodology. meshing characteristics in rigidity condition are studied. these characters include the inductive normal curvature along the contact line on the worm surface, the first and the second limit lines during the engage of the worm gear, and the influence of the intersect angle between the contact line the relative velocity of the worm and the gear on transmission performance

    根據漸開線圓柱蝸桿傳動的創成方法，建立了漸開線圓柱蝸桿和蝸輪的接觸線方程式、齒面方程式，分析了漸開線圓柱蝸桿傳動的剛性嚙合特性，如蝸桿與蝸輪嚙合時的誘導法曲率、一類界限曲線、二類界限曲線和蝸桿與蝸輪間相對速度方向和接觸線方向的夾角對傳動性能的影響； 2
  9. Accuracy of fine - pitch cylindrical worm and wormwheel

    小模數圓柱蝸桿蝸輪精度
  10. Terminology and symbols for cylindrical worm and wormwheel

    圓柱蝸桿蝸輪術語及代號
  11. Larger loading capacity under the same specification ; easily establishing lubricant oil film, smaller friction coefficient, higher transmission efficiency, saving energy ; highest accuracy up to grade 3 of din standard ; smoother functioning, lower noisiness and longer service life

    平麵包絡環面蝸桿與普通圓柱蝸桿傳動相比具有更大的承載能力，易於建立動壓油膜摩擦系數小，傳動效率高節省能源具有可磨削性，能達到din標準三級，面粗糙度優于ra0 . 4而且具有運行平穩噪音低壽命長等優點。
  12. The fuzzy optimal design of circular cylinder worm - drive

    圓弧齒圓柱蝸桿傳動的模糊優化設計
  13. Analysis on oylindrical worm in traction machine and modifications

    圓柱蝸桿傳動曳引機的剖析與改進
  14. Analysis of the elastohydrodynamic lubrication of arc cylindrical worm drive

    圓弧圓柱蝸桿傳動彈流潤滑分析
  15. Series of modules for gears ; modules for cylindrical worm gear transmissions

    齒輪用模數系列.第2部分:圓柱蝸桿傳動裝置的模數
  16. Cylindrical worm gear

    圓柱蝸桿副
  17. Accuracy of cylindrical worm and wormwheel

    圓柱蝸桿蝸輪精度
  18. Cylindrical worm and wormwheel information of the dimensional data to be given on the drawing

    圓柱蝸桿蝸輪圖樣上應註明的尺寸數據
  19. Arc - contact worm

    圓弧圓柱蝸桿
  20. The involute cylinder worm gear is one of the ordinary cylinder worm gears. because of the specificity of the machine tool for this worm gear, its machine tool is not extensively developed in our country. the deep research on the involute worm gear is lack in our country

    漸開線圓柱蝸桿是普通圓柱蝸桿中的其中一種，但由於加工這種蝸桿的機床的專用性太強，我國沒有廣泛發展這種機床，因此我國對漸開線蝸桿的研究還不夠深入。
分享友人
分享到 Line

分享到臉書