均勻底流 的英文怎麼說
中文拼音 [jūnyúndeliú]
均勻底流
英文
uniform underflow-
Abstract : based on thestatic wind force factors of a tower and on the root - mean - square of the buffetingdisplacement responses of the tower top, which are measured by wind tunnel tests inlaminar and turbulent field respectively, the static and buffeting internal forces of thetower bottom control sections under its design wind speed are obtained by linearsuperposition method and fem
文摘:基於均勻流和紊流風場中的橋塔模型風洞試驗所測得的橋塔空氣力靜力系數及塔頂抖振響應的位移均方根,採用線性疊加法及有限元法反演,給出設計風速下塔底控制截面的順風向靜風及抖振內力。Installation requires no water draining. simply lower the pipes at tank side and let it sink to the bottom to send up air for aeration. for maintenance, pull up pipe to remove surface deposits, then return it to bottom again
個細孔出氣,上升帶動全池污水繞流均勻,施工免抽水,由池上放入污水池邊,使其沉下池底送風曝氣即可,保養時上拉清除表皮再放回即完成。Mushy pvc ( dop + additives ) - beater ( stir well ) - vacuuming ( materiel has been completely dewatered and debubbled after vacuuming ) or mix with color paste which has been processed by ball mill and then dropped into mould cavity by needle cylinder ) - solidified in the constant temperature box ( color fixing ) - input basic material - sent to the constant temperature box in the flowing way and then forming and then forming and sent out automatically - cooled by fan - finished products
糊狀pvc (增塑劑dop +助劑- - -打漿機攪拌均勻- - -抽真空處理) (真空機處理后的物料已完全脫離水分和氣泡)或球磨機處理后的色漿混合後用針筒滴入模具形腔- - -放入恆溫箱中固化(色彩定形) - - -注入底料- - -流水式送入恆溫機,定型后自動送出- - -風扇冷卻- - -成品Emission is inducted evenly into the reactor, and effectively interact with recovery solvent sprayed down from top in the filler layer, then passes through the gas and liquid separation system to eliminate moisture for releasing clean air
廢氣由塔槽底部均勻進入洗滌塔,並在填充層與由上端噴流而下的洗滌液作有效的交換洗滌,再經由氣液分離系統去除水氣,清潔的空氣由出口排出。Shortcut calculation of the depth and bottom width of uniform flow in ladder - shaped open canal
梯形明渠均勻流水深和底寬的簡捷計演算法Operator - splitting method for calculating uniform flow depth s and bed widths of rectangular open channels
矩形明渠均勻流水深和底寬的運算元分裂演算法In this paper, the reason for which the substrate temperature effects the nonuniformity of umbirfpa is analyzed. it is brought forward that using three point correction method to minish the substrate temperature ' s influence on nonuniformity of umbirfpa. the principle of the new method, the way to realize the method and the flow process to obtain the correction coefficients were given simultaneously
文中分析了umbirfpa的非均勻性受襯底溫度影響的原因,計算了襯底溫度對非均勻性影響的大小,提出採用三點非均勻性校正新方法來克服襯底溫度的影響,並分析了這種新方法的原理、實現方案和校正系數的獲取流程。Asymptotic coupling algorithm for water depth and bed width of uniform flow in rectangular open channels
矩形明渠均勻流水深及底寬的漸近耦合演算法The experimental results showed that firstly, the distribution of resistiveity, mobility, carrier concentration, epd and ab - epd in gaas substrate was not uniform ; secondly, the distribution of electrical parameters depended on that of epd and ab - epd ; thirdly, mesfet devices performance correlated with ab microdefects ; last, as shown by pl mapping results, it is substrate with better parameters quality that could provide more chance to fabricate good mesfet devices
實驗結果表明, lecsi - gaas的電阻率、遷移率、載流子濃度、位錯密度和ab微缺陷分佈都不是均勻的,且電參數的分佈與ab - epd 、位錯密度分佈有關。製作的mesfet器件的性能參數分佈與ab微缺陷有明顯聯系。從plmapping測量結果可以看出材料的襯底參數好,則pl譜的強度高, pl譜均勻性也好,器件參數也好,就有可能製作出良好的器件與電路。分享友人