坡口焊 的英文怎麼說

中文拼音 [pōkǒuhàn]
坡口焊 英文
groove welding
  • 坡 : Ⅰ名詞（地面傾斜的地方） slope Ⅱ形容詞（傾斜） sloping; slanting
  • 口 : Ⅰ名詞1 （人或動物進飲食的器官; 嘴） mouth 2 （容器通外面的地方） mouth; rim 3 （出入通過的地方） ...
  • 焊 : 動詞（用熔化的金屬修補金屬器物或使金屬工件連接起來） weld; solder
  1. As one kind of key equipment in piping work of large - scale turbo - generator set in power plant, the machine is especially applicable to various welding bevels, flat end and angle of outer & inner diameter of ascending pipe, elbow pipe, bend, flange and etc., which greatly meets demands in pipe processing of construction site and manufacturers

    本機床是電站大型汽輪發電機組的管道施工的關鍵設備，對直管、彎管、彎頭、法蘭等管體的各種型式焊接坡口，端平面，內外徑過緩斜度及直口，能滿足施工現場和製造廠家對各種管件的加工要求。
  2. Cracks have been found in the flange and web splices at groove welds in at least four bridges.

    至少在四座橋梁的翼緣板和腹板拼接坡口焊縫中發現了裂紋。
  3. These attachments were considered secondary components, so no weld quality control has been imposed on the groove weld splice.

    這些附連件被看作是次要的部件，所以在這種坡口焊接中沒有進行焊接質量控制。
  4. Add metal from the rod by dipping the end into the pool so that it melts and makes up the vee.

    將焊條一端浸入池內熔化，填滿V形坡口。
  5. This paper describes the difference between the terms of groove and bevel in weld joints and condition in asme code translation

    本文敘述焊接接頭中術語剖口與坡口的區別和在asme規范翻譯中應注意的問題。
  6. 5 all single - sided groove joints in nickel alloys, stainless steel and ferritic alloys containing more than two ( 2 ) percent chromium shall be welded using a gas tungsten - arc root pass with an inert gas back purge

    鉻含量超過2 %的鎳合金、不銹鋼和鐵素體合金的單面坡口焊道用鎢極氣體保護焊，其根部焊道用惰性氣體反吹。
  7. Often lack of fusion adjacent to the girder web in the transverse groove welds led to the cracking.

    在靠近主梁腹板的橫向坡口焊縫處常常出現未熔透而導致裂紋。
  8. This chamfering machine employs the principle of rolling shear to shear the edge of the steel plate according to the angel needed, to obtain the bevel for w - elding

    該倒角機利用滾剪原理，對鋼板邊緣按所需角度進行剪切，以得到焊接所需坡口。
  9. For all processes, the welding procedure specification ( wps ) shall contain a detailed cleaning procedure indicating joint preparation prior to welding

    對于所有焊接方法，焊接工藝規程都應詳細包含清除方法，說明焊前坡口的準備。
  10. This consists for the most part in straightening up, cleaning, and, on thicker plates above 5/16 in vee-ing the edges.

    主要是矯直，清選，對于厚度超過516英寸的金屬板，還需將焊邊做成V形坡口。
  11. The second crack is a crack originating at the groove weld toe of the column flange-girder flange connection.

    第二種是產生於立柱翼緣與主梁翼緣連接處的坡口焊縫焊趾處的裂紋。
  12. Range of use : cz2. 5 air shovel is used for clearing slag by electric welding, beveling groove. it also can do some shovelling and cutting on steel cast

    使用范圍： cz2 . 5型氣才鏟適用於電焊去渣、去毛邊、去坡口，也可在鋼結物體、鑄件上進行少量鏟削。
  13. A large number of these cracks occurred because the groove welded component was considered a secondary member or attachment.

    發生這許多裂紋是因為把這些坡口焊接部件作為次要構件或附件考慮。
  14. Weldability testing - method of y - groove cracking test

    型坡口焊接裂紋試驗方法
  15. Method of u - groove weld cracking test

    U形坡口焊接裂紋試驗方法
  16. Method of y - groove weld cracking test

    Y型坡口焊接裂紋試驗方法
  17. 1 process - oriented algorithms for sheet metal deployment. an investigation is made on the constrains to welded seam, sheet thickness, slope type and their influences to sheet metal manufacture process, and a rational method is adopted to treat design and calculation

    本文主要涉及的研究內容及創新點包括以下幾個方面： 1 、提出並實現了面向工藝的鈑金展開演算法；探討了展開計算時焊縫邊界約束條件，板厚處理，坡口型式對鈑金加工製造工藝的影響，並採用合理的方法進行處理和設計。
  18. 4 double - welded groove joints shall have their root passes back gouged to sound metal on the reverse side before proceeding with welding on that side

    雙面焊接的坡口焊道，應在焊接前將該面底部焊道逆向刨削，直到其對面露出完好的金屬。
  19. Weld with shop beveled ends

    工廠加工坡口焊接
  20. Flare groove welding

    喇叭形坡口焊
分享友人
分享到 Line

分享到臉書