坯體 的英文怎麼說

中文拼音 [pītǐ]
坯體 英文
cla
  • 坯 : 名詞1 （未經燒制的磚、瓦、瓷等的製品） base 2 （土坯） unburnt brick; earthen brick; adobe 3 [方...
  • 體 : 體構詞成分。
  1. We also attainted mosi2 / sic composite by using melting mosi2 infiltrated sic body which shaped by sic powder. the result show that the diameters of sic particle and shaping methods have effect on the composite ' s microstructure and properties

    另外，嘗試了用mosi _ 2在2050下浸滲直接由sic粉體成型的坯體制備mosi _ 2 / sic復合材料。採用sic顆粒的級配有利於提高坯體密度，但是降低燒結體的緻密度。
  2. The shaped briquet was sintered at 1600 for 2. 5 hours under normal pressure and at certain heating rate in si - mo electric furnace

    成型后的坯體置於硅鉬棒電爐中，在常壓、適當升溫速率下於1600保溫2 . 5小時燒結。
  3. The powder was pressed through molding and cold isostatic pressure, which increased the density and decreased the uneven distribution of stress inside the briquet to make the ceramic briquet equally compact

    粉料採取模壓和冷等靜壓相結合的方法壓制，增大了坯體內部的密度並減少了應力的分佈不均，得到均勻緻密的陶瓷坯體。
  4. To meet the processing requirements before sintering, the pressed briquet was pre - calcined at 1150 to make it possess adequate processing strength at first and then was shaped through precise turning on the numerical control lathe according to the design diagram of the femoral head prostheses of partial hip joint

    為滿足燒結前坯體加工的要求，壓制后的坯體在1150預燒，使其具備一定的加工強度，然後按照半髖關節股骨頭假體的形狀尺寸設計圖在數控車床上進行精密車削成型。
  5. Color - painting is of two sorts : overglaze painting and underglaze painting. overglaze painting, with five - colored painting or fencai as its example, is to outline patterns with zhuming pigment and to fill them with various colors on the already glazed surface of the porcelain, before it is placed into a closed oven for a further baking at a compar - atively low temperature from 700 to 800c. underglaze painting is to paint with qinghua, underglaze red and other pigments on the body before it is glazed. its feature is that all the colors are under the glaze formed at high temperature and thus will never fade away

    釉上彩如五彩粉彩等，是在已燒成瓷的釉面上描繪紋樣填彩，再入紅爐以低溫燒烘，溫度約700 - 800度。此外，燒窯前即在坯體素胎上繪畫，如青花釉里紅等，則稱為釉下彩，其特點是彩在高溫釉下，永不退色。
  6. Study on preform of c c composites for aircraft brakes

    復合材料坯體結構的研究
  7. In this paper, the effecting factors such as slip mixture, temperature, working mould quality and technology parameters on the ceramic green ware embryonic forcefulness were a nalyzed by analyticity hierarchy process technology

    本文對直接影響坯體質量的挺形性因素：泥漿配方、泥漿溫度、工作模質量和工藝參數，採用美國薩迪教授的層次分析技術，進行各種復雜因素的權重排序分析，為「九五」相關項目的優化原始數據和提供原始數據奠定基礎。
  8. Abstract : in this paper, the effecting factors such as slip mixture, temperature, working mould quality and technology parameters on the ceramic green ware embryonic forcefulness were a nalyzed by analyticity hierarchy process technology

    文摘:本文對直接影響坯體質量的挺形性因素：泥漿配方、泥漿溫度、工作模質量和工藝參數，採用美國薩迪教授的層次分析技術，進行各種復雜因素的權重排序分析，為「九五」相關項目的優化原始數據和提供原始數據奠定基礎。
  9. Therefore, the purpose of this thesis is to look for a suitable preparing process for 3 - tcp with their micro - construction controlled more easily and the porosity rate and strength uniform. this paper created a new preparing method of porous ceramics, i. e. foam gel - casting technique, which integrated foam technique in porous ceramics preparing and gel - casting technique in structural ceramics preparing was applied to improve the preparing technique of porous p - tcp bioceramics in order to prepare ceramics bodies with high body intensity, controllable porosity and easily machining performance

    因此，本論文努力尋求一種適合於- tcp多孔陶瓷的制備工藝，使其微觀結構易於調節控制，空隙率和強度達到平衡同一。在實驗中，結合了制備多孔陶瓷常用的發泡法和結構陶瓷制備中的注凝法，創新設計了一種新的多孔陶瓷成型方法? ?泡沫注凝法，對多孔- tcp生物陶瓷的成型工藝加以改進，制備出高強度、氣孔率可控以及易加工的陶瓷坯體。
  10. When heating temperature reached 300, crackings appeared on the surface of ceramic tiles but the microstructure of glaze exhibited no apparent change when heating temperature reached 900, the glaze melted, the crystal structure of the tiles broke down, the integrity of ceramic tile was destroyed and the intensity was almost lost

    當溫度達到300 ，冷卻試驗時，釉面可產生裂紋，但顯微結構基本無變化；當溫度達到900 ，冷卻試驗時，釉面出現熔化現象，坯體晶體結構酥裂、破碎，完整性遭到破壞，強度基本喪失。
  11. Theimportant technological parameters, which influence significantly thecharacterization of the screen - printed ysz electrolyte thin films, includingparticle size and particle size distribution of the starting ysz powder, composition of the screen - printing ink, sintering temperature of the screenprintedysz green films and printing times were investigated in detail

    系統研究了影響絲網印刷工藝的幾個重要參數，如ysz粉末的粒徑及粒徑分佈、印刷漿料的組成、電解質膜坯體的燒結溫度和印刷層數。
  12. Sintering behaviors of sub - micron - al2o3 green compacts at constant heating rates

    3坯體的恆速升溫燒結行為
  13. It shows with the increase of the amount of the mo in the si - mo infiltrant, the density of the infiltrated materials with the same performs increased, but the amount of the free carbon and pore also increased. it was the result of the capillary chocking - off caused by the separation of the mosj2 from the alloy infiltrant during the sintering process. after th thermal treatment at 2050, the amount of the free carbon and pore decreased. also. another cause for the unfully conversion of c into sic was the gas pressure. larger than the capillary force

    實驗表明，對于同一坯體，隨著si - mo熔體中mo含量的增加，浸滲所得材料的密度隨之增加，但是，材料中的殘留c 、氣孔相的含量亦隨之增加。這是由於反應浸滲時，熔體中析出的mosi _ 2阻塞毛細管造成的。含殘留c 、氣孔相的材料進行高溫（ 2050 ）熱處理后，材料中殘留c 、氣孔相的含量大大減少。
  14. Inletting body temperature

    坯體的入窯溫度
  15. Color - painting on the porcelain ware is different from common painting. the pigment of glaze and painting on the body will undergo a great change after firing and baking at high temperature. it is in itself amazing that through kiln - firing a half - finished porcelain with dark colors and an unattractive look can be transformed into a work with so wonderful colors. from this, we can understand how exceptional the experience and imagination it requires in porcelian color - painting

    瓷器的彩繪與一般繪畫不同。因為畫工在坯體素胎上施釉和作畫時所見的顏料色，在經過高溫燒制和烘烤后會發生很大變化。看到一件件顏色暗淡貌不驚人的半成品，經過爐火的燒煉竟會呈現出如此絢麗奪目的色彩，這本身是奇妙的而與此同時也便可以得知，為瓷器作畫是需要怎樣的特殊經驗和想象力了。
  16. At 1800 c heat sic body for two hours can elimilated the sio2 which on the sic surface and is good for increasing the density of composite. increasing infiltration temperature has no effect on composite ' s density

    將排硅后的sic坯體在1800長時間保溫有利於去除sic表面的sio _ 2 ，提高復合材料的緻密性。
  17. The mud block is thrown on the center of the jolly s revolving disk, and if changed into a basic form of porcelain body accompanied body accompanied with the manual processes of squeezing and pulling and others

    拉坯將泥團摔擲在轆轤車的轉盤中心，隨手法的屈伸收放拉制出坯體的大致模樣。
  18. The body is covered on the trimming tube of jolly, then revolving the table of the wheel and rotary - cutting the body with a cut, generating a suitable thickness of the body and a smooth of inner and outer surfaces. this is a step of technology process which is very strict demand

    將坯覆放于轆轤車的利桶上，轉動車盤，用刀旋削，使坯體厚度適當，表裡光潔，這是一道技術要求很高的工序。
  19. Use caution, porcelain body or the coating of brick bottom, which has high content of low - melting oxide and fuel which has more impurity, that all can corrode the roller

    富含堿性氧化物成分的瓷磚坯體或磚低塗料，以及雜質含量高的燃料，都可能侵蝕輥棒，須謹慎使用。
  20. Sic whisker is incorporated in the raw material of reaction bonded silicon carbide ( rbsc ) to prepare sicw / sic composites. the effect of fabrication process on the microstructure and the properties of the sintered body are investigated in this paper. based on the research results on the sinter process, it is concluded that the sic whisker solve rapidly even at 1450

    本課題將sicw引入反應燒結碳化硅（ rbsc ）體系，提出了一種制備高sicw含量sicw / sic復合材料的思路，研究了材料制備工藝對sicw / sic復合材料顯微結構的影響，討論了sicw / c坯體的反應燒結機理，對材料顯微結構與力學性能的相關性作了研究。
分享友人
分享到 Line

分享到臉書