塑性屈服點 的英文怎麼說

中文拼音 [sùxìngqūbìdiǎn]
塑性屈服點 英文
plastic yield point
  • 塑 : 動詞（塑造） model; mould
  • 性 : Ⅰ名詞1 （性格） nature; character; disposition 2 （性能; 性質） property; quality 3 （性別） sex ...
  • 服 : 服量詞（用於中藥; 劑） dose
  • 點 : Ⅰ名詞1 （液體的小滴） drop （of liquid） 2 （細小的痕跡） spot; dot; speck 3 （漢字的筆畫「、」）...
  1. Based on the analysis of mechanism for joint region, the " frame - wall " and " aslope compression stub column " mechanical models and yielding patterns of core zone of the joints are set up. the shear load - carrying formulation for joint core zone is also given in terms of plastic ultimate analysis. and then, the comparisons between the formulas given in this paper and that of chinese design code ( draft ) and nonlinear fem as well are presented

    對節點核心區的抗剪，通過受力機理的分析，建立了鋼「框架剪力墻」加混凝土「斜壓短受力體系及其屈服機制，根據塑性極限分析，給出了節點核心區抗剪承載力計算的迭加公式， 《規程》公式和非線性有限元近似模擬分析結果進行了比較。
  2. The calculation results indicate that the outboard of drum walls fall in plastic yielding at the same time the rising cooling water reaches the height of that point and the yield region becomes narrower and narrower when it comes closer to the circumferential strake weldments, which explains the reason coke drums experience bulging and cracks occur in the weld seams portions of shell to shell after long in service

    計算結果表明：塔壁外側在冷卻水面到達的瞬間進入塑性屈服，筒節中部塑性屈服區較大，當靠近焊縫時塔壁的塑性變形區逐漸縮小直至消失，塔壁塑性屈服區的分佈特點解釋了塔體長期使用后發生鼓凸變形及簡體與焊縫連接處產生裂紋的原因。
  3. After pretorsion the successor tensile yield limit and strength limit both improved very highly, but the trend of the increase of the strength limit was suspended till the pretorsional capacity reached 17, when the pretorsional capacity was greater than17 ( prestrain value was 81. 19 % of total strain ), the successor strength limit rapid failed and approached the yield limit. this illustrate the a3 steel specimen translate from plasticity into friability after pretorsion strengthen. when the specimen was operated by tension - torsion action, the yield limit had very large improved, but the strength limit changed very little. furthermore, the trend of the increase of the strength limit was suspended till the pretension capacity reached 0. 25 ( prestrain value was 66. 93 % of total strain )

    A3鋼試件在預扭轉后，后繼拉伸屈服極限和強度極限均有很大提高，但強度極限的增大趨勢到預扭轉量為17為止，預扭轉量大於17 （預應變值為總應變的81 . 19 ）后強度極限迅速下降，與其屈服極限接近，這說明a3鋼試件經預扭轉強化后逐漸由塑性轉化為脆性。該預應變值為a3鋼試件的韌脆轉變點。 a3鋼試件在拉伸-扭轉作用下，屈服極限有很大提高，但強度極限沒有多大改變，而且，屈服極限的增大趨勢到預拉伸量為0 . 25應變（預應變量為總應變量的66 . 93 ）后就不再增加。
  4. ( 2 ) based on the detail analysis on soil models and machine gun firing dynamics, the drucker - prager model is introduced to study machine gun firing dynamics, the soil is modeled like a box by finite element

    在詳細分析目前土力學中出現的土壤的各種本構模型及機槍發射動力學研究特點的基礎上，指出採用drucker ? prager屈服準則的彈塑性模型是機槍發射動力學研究中應該採用的主要的土壤本構模型。
  5. In terms of strength and ductility, the concept of specified yield point is put forward. based on the principle that under the same condition ( that is, the size of cross section, material strength and reinforcement ratio are identical ), the resultant ultimate moment must be identical, the compression failure of frp reinforced concrete beam is equal to the tension failure for the viewpoint of design and calculation

    從強度與延性兩方面的綜合考慮，提出了纖維增強塑料筋名義屈服點的概念，對發生受壓破壞的纖維增強塑料筋混凝土梁，按照同樣條件下（截面尺寸、材料強度、截面配筋率等均相同）截面承載力相等的原則等效轉化為受拉破壞進行設計與計算，以此確定纖維增強塑料筋的強度折減系數_ f 。
  6. On the basis of expounding the effects of plastic deformation behavior and forming limit on the analysis of sheet metal forming, this paper overviews the research progress on yield criterion, hardening model, forming limit and effects of complex loading paths, and obtains that establishing the test method of complex loading paths according with sheet forming characteristics, verifying the accuracy and applicability of theoretical results, and determining the analytic description and practical criterion under complex loading paths, are main research directions in sheet metal forming

    摘要本文在闡述塑性變形行為與成形極限對于解析板料成形過程的作用與意義的基礎上，針對板料屈服準則、強化模型、成形極限及復雜加載路徑的影響規律的研究進展進行了綜述與分析，得出：建立符合實際板料成形特點的復雜加載路徑的實驗方法，驗證理論研究結果的準確程度及適用范圍，確定復雜加載路徑下的解析描述及實用判據，是目前該領域主要的研究方向。
  7. Which adopt plastic analysis method, and take for reinforcement damage as failure criterion

    本文公式採用塑性分析方法，以縱向鋼筋屈服破壞為節點破壞的準則。
  8. Through analysis and compare, the measure fitting for huxi bank was put forward. ( 3 ) introduced fast lagrangian analysis of continua. flac3d is a three - dimensional explicit finite - difference program. it can simulate the behavior of three - dimensional structures built or soil, rock or other material and can simulate plastic collapse, flow and large - strain accurately

    （ 3 ）對三維快速拉格郎日有限差分法進行了介紹，三維快速拉格朗日法是一種基於三維顯式有限差分法的數值分析方法，它可以模擬巖石或土體及其它材料的三維力學行為，可以準確模擬材料的屈服、塑性流動、軟化直至大變形，尤其在材料的彈塑性分析、大變形分析以及模擬施工過程等領域有其獨到的優點。
  9. For metals that experience the gradual elastic - plastic transition, the point of yielding is determined as the initial departure from linearity of the stress - strain curve and this is sometimes called the proportional limit

    對于金屬逐步的彈塑性形變轉變，其屈服點確定為應力應變曲線非線性關系的開始，這個點也被稱為比例極限。
  10. The mesh of finite element was generated automatically to simulate the true fabric of concrete. the different material property of elements was identified and assigned automatically. the nonlinear constitutive relation of materials was established

    採用非線性本構模型來表徵組成三級配混凝土的各種材質的非線性應力?應變關系，該本構模型具有可以模擬材料的開裂、拉伸軟化、塑性屈服和壓碎非線性等特點。
  11. This paper investigated the electrorheological ( er ) characteristics of two suspensions of starch particles ( a ) and aluminosilicate particles ( b ) in silicone oil respectively, and also their transmitting properties on a simulated device of cylindrical er clutch ( erc ) by comparison, only to show that a is a kind of electrorheological fluid ( erf ) with definite plastic yield - point and can be subjected to a narrow voltage range on erc, while b is a kind of pseudo - plastic erf and can be subjected to a wilder voltage range on erc

    本文研究了硅油-澱粉（ a ） 、硅油-硅酸鋁（ b ）兩種er流體的電流變性能，並通過一套筒式er離合器模擬傳動裝置，研究且對比了這兩種er流體在筒式er離合器上的傳輸特性。結果表明a是具有塑性屈服點的流體，其在er離合器上有效調速電場范圍較小； b是假塑性流體，其在er離合器上有效調速電場范圍較寬。
分享友人
分享到 Line

分享到臉書