塑性平面應變 的英文怎麼說

中文拼音 [sùxìngpíngmiànyīngbiàn]
塑性平面應變 英文
plastic plane strain
  • 塑 : 動詞（塑造） model; mould
  • 性 : Ⅰ名詞1 （性格） nature; character; disposition 2 （性能; 性質） property; quality 3 （性別） sex ...
  • 平 : Ⅰ形容詞1 （沒有高低凹凸 不頃斜） flat; level; even; smooth 2 （高度相同; 不相上下） on the same l...
  • 面 : Ⅰ名詞1 （頭的前部; 臉） face 2 （物體的表面） surface; top 3 （外露的一層或正面） outside; the ri...
  • 應 : 應動詞1 （回答） answer; respond to; echo 2 （滿足要求） comply with; grant 3 （順應; 適應） suit...
  1. In view of bearing capacity of the elastoplastic theory analysis, the author made a comparison between the achieved bearing capacity limit load pi / 4 of round base ( space problem ) and the limit load pi / 4 of bar groundwork foundation design ( plane problem ) from soil mechanics at home and abroad as well as foundation criterion, and explained why the value of formula in present design criterion from soil mechanics is inclined to be conservative. in the light of the author ' s many years experience of vibration test on the spot and the research work of relevant projects, the author worked over the dynamic pile testing of the bearing capacity of foundation and batholith, and gathered the parameter of dynamic analysis and testing. the author also talked over the difficult point of pile foundation design criteria in present batholith engineering world, i. e. the confirmation of batholith bearing capacity of pile end, from the following aspects : a ) confirmation of single axis counter - pressure strength of rock in house ; b ) f. e. m calculation of elastoplastic model ; c ) calculation of soil mechanics ; d ) deep well load test

    然後，對巖土工程領域至今尚未解決，甚至不為人注意的考慮地基變形的地基承載力問題進行了實用化的探討，提出了考慮地基變形的地基承載力上程計算方法；對基於彈塑性理論分析的地基承載力國內尚未見報道的空間問題得到了圓形基礎（空間問題）的承載力界限荷載p _ （ 1 / 4 ） ，並與國內外土力學專著及地基基礎設計規范中的條形基礎（平面問題）的界限荷載p _ （ 1 / 4 ） ，進行了對比，從而定量上解釋了目前設計規范引用土力學承載力公式值偏於保守的這一情況；根據本文作者多年從事現場地基工程振動試驗及相關課題的研究工作，本文以截頭錐模型模擬地基，對地基（巖基）承載力的動測法進行了研究，為各類地基（包括巖基） ，匯總了動力分析和檢測川的參數：針對日前巖土工程界應用樁基設計規范中的難點? ?樁端巖基承載力的確定問題，從巖石室內單軸抗壓強度確定、基於彈塑性模型的有限單元法計算、土力學計算及深斤載荷試驗四方面進行了深入討論；本文作者根據多年現場載荷試驗的工程實踐，對深井荷試驗裝置的核心部分? ?反力裝置，設計了側壁支撐反力加載系統，該加載系統具有實用、簡便、穩定及安個等優點。
  2. Based on the design of hanpingzui rockfill dam with concrete facing slab, the stresses and deformations of the dam body and impervious system are calculated by using the elastoplastic plane finite element method

    摘要根據漢坪咀混凝土面板堆石壩的工程設計，用彈塑性平面有限元法，計算了堆石壩壩體、防滲體系的應力和變形。
  3. The explicit finite element method ( fem ) based on the varying time - step was selected to analyse the dynamic roll - pass process ; the nodes on the leading face of the steady - state elements set was extracted and projected onto a plane to give the required mesh, also called the origin mesh ; the implicit fem was selected to analyses the inter - pass transient thermal process ; a geometric part from the mesh was generated and meshed by using the quadrilateral elements, a heat transfer analysis was selected to transfer the node temperature data ; a new model was created by using hexahedral elements, mapping the node temperature and the equivalent plastic strain on the integration points

    利用基於變步長中心差分格式的顯式積分方法分析瞬態軋制過程；提取穩態單元集節點形成截面網格；利用隱式積分方法分析軋制道次間隙瞬態溫度場；對型鋼斷面進行平面四邊形網格劃分並映射節點溫度數據；利用六面體單元構建有限元分析模型，映射單元節點的溫度、積分點的等效塑性應變，進行數值分析。
  4. The choice dam type is especial importance, during the designed research of the rock - fill dam, particular under the rock - fill dam with very deeply cover layer, the stress and strain of the middle wall and cutting interpenetration wall of the dam foundation is mostly sensitive, whether the. design of dam is scientific and reasonable, it is very important for cutting interpenetration and stability of the dam, the article offer the reference for the design of cutting interpenetration in the foundation with deep cover with earth the water conservancy in xiaban zone, based on the study and analysis the design of cutting seep in the foundation with deep cover with earth, cutting interpenetration concrete wall and the joining model of cutting interpenetration material in body of dam and the applying effect in the practical worko based on the foundation which absorbed and summarize the achievement of design and research in the inter and outer country, for the project of the clay vertical middle wall and vertical cutting interpenetration, the asphalt concrete vertical middle wall and vertical cutting interpenetration the clay inclined middle wall and the lever carpet layer cutting interpenetration, respectively in terms of the different stage of complete period sluice period and working condition, adopting nonlinear calculate and analysis with the finite element method ; carrying the analysis and study with the 3d finite element method as to the different joining model of the left bank high slope cutting interpenetration body and the foundation concert cutting interpenetration wall ; carrying the analysis and study with the 3d finite element method as to the effect of the wall stress and strain because of the different elasticity modulus of the concert cutting interpenetration wall through the analysis and study with the different project. have comparatively all - around comprehended the various model dam, particular the distribute rule of stress and strain of the cutting interpenetration system, provide for the important evidence of the plastic area size the join model of the foundation cutting interpenetrate wall and dam body cutting interpenetrate system the choice of the dam model and the design of the structure of the dam body, the result of research and advice have very importance value in design and building for the similarity project

    工程設計中，壩型的選取顯得尤為重要，特別對于壩基有深厚覆蓋層的堆石壩，心墻和壩基防滲墻的應力和變形是壩體、壩基最敏感的部位，設計方案是否安全、科學和合理，對大壩防滲和穩定起到至觀重要的作用。本文研究分析了國內外深厚覆蓋層基礎防滲設計、壩基混凝土防滲墻與壩體防滲體銜接形式及工程實際應用效果，為下坂地水利樞紐工程深厚覆蓋層基礎防滲設計的方案選擇提供了參考；在吸收和歸納了國內外堆石壩的設計研究成果的基礎上，對粘土心墻和壩基垂直防滲方案、瀝青混凝土心墻和壩基垂直防滲方案以及粘土斜心墻和壩基水平鋪蓋防滲方案，分別按竣工期和蓄水運行期的不同工作情況進行了有限元非線性計算分析；對左岸高陡邊坡的大壩防滲體與基礎混凝土防滲墻的不同結合型式進行了三維有限元靜力計算分析和研究；對混凝土防滲墻不同彈性模量對墻體應力和變位的影響進行了三維有限元靜力計算分析和研究。通過對不同方案的計算分析和研究，比較全面的了解了各方案壩體，尤其是防滲體的應力和變形分佈規律，為壩型選擇、壩體結構設計、基礎防滲墻與壩體防滲體的結合型式以及塑性區大小的確定提供了重要依據。
  5. Standard test methods for plane - strain fracture toughness and strain energy release rate of plastic materials

    塑料材料平面應變斷裂韌性和應變能量釋放率的標準試驗方法
  6. Taken the viscosity into account in this paper, a rather simple but practicable elastic - viscoplastic model to describe the stress - strain relation of the material at the crack - tip of antiplane mode iii crack

    本文在考慮擴展裂紋尖端材料的粘性效應下，採用一種比較簡單然而實用的彈粘塑性模型來描述反平面型動態擴展裂紋尖端場附近材料的應力應變關系。
  7. Then, a step - by - step increase of vertical curvature is applied to the hull girder assuming that the plane cross section remains plane. at each incremental step, the stress of the cross section is evaluated using the average stress - strain curves of the elements as well as the incremental bending moment due to the curvature increment. performing sample calculations on existing girder models tests under pure bending, the rationality of the proposed method was examined

    假設船體橫向框架材足夠強，因而板架的整體破壞不會發生；基於梁?柱理論、理想彈塑性假設、平面假設，建立了拉伸和壓縮加筋板單元的平均應力?應變關系曲線，應用船體結構總縱極限強度的簡化逐步破壞分析方法計算船體總縱極限彎矩，並據此開發了計算程序sus 。
  8. Elastic - plastic analysis for soil around anchor jacked pile in this paper, the course of penetration is regarded as expansion of cylindrical cavity in infinite soil mass. combining with the knowledge of elastic mechanics and plastic mechanics, we can make analysis for soil around pile. finally, we can educe the cylindrical cavity pressure, radius of plastic zone, radical displacement in elastic zone, excess pore water pressure in soil around pile and spherical cavity pressure at the end of pile

    錨桿靜壓樁樁周土體的彈塑性分析該部分是文章的主要工作所在，本文把壓樁過程樁周土體的本構關系看作是水平面的平面應變小孔擴張問題，利用小孔擴張原理，結合彈性力學以及塑性力學的知識，對壓樁後土體的性狀作出分析，得出樁對土的擠擴作用力、樁周土體塑性半徑、彈性區的位移，壓樁完成瞬時樁周土體彈性區和塑性區的超孔隙水壓力以及樁端球形孔擴張的擴張力。
  9. The experimental research for beam - to - column connections of steel frame and the research influence on the steel frame is one subject of 2001 ' key research subject of ministry of construction of china, grant no. 01 - 2 - 085. researching for of beam - to - column connections under cyclic loading, for the factors effecting on the connections, for the deformation and failure character of connections, the arising order of plastic hinges and load - deformation hysteretic behavior of three pane frame under cyclic loading, the effect of semi - rigid connections on the frames, is the major purpose of this study

    本文進行的鋼框架樑柱連接的試驗研究和對框架的影響研究是建設部2001年科技攻關項目《新型空腔結構板輕鋼結構體系應用研究》的子課題，旨在研究樑柱連接在循環荷載作用下的滯回性能、影響連接的各種因素、連接變形特徵和破壞特徵；研究三榀平面鋼框架在循環荷載作用下構件塑性鉸出現的順序， p ?的滯回性能以及半剛性連接對框架側移以及塑性鉸出現順序的影響。
  10. In this paper, systematic numerical test have been carried out to study the stability of surrounding rock mass with different distribution of weak interbed, different distance between weak interbed and limit of excavation, different thickness of weak interbed, in the different confining coefficient and representational surrounding rock mass graded ii, iii, iv. all of the numerical modeling is plain - strain type with elastic - plastic constitutive law and mohor - coulomb failure criterion, through the integrated numerical analysis program final. plentiful numerical test results have been drawn via analyse the deformation, tensile stress region, plastic region of surrounding rock and the stress status of shot - crete

    大量的工程實踐表明，軟弱夾層對地下洞室圍巖穩定性的影響有著決定性的作用，本文以大型數值模擬分析系統final為平臺，採用彈塑性應力應變關系和m - c屈服準則建立平面應變問題有限元模型，對軟弱夾層的分佈部位、分佈距離、軟弱夾層的厚度對圍巖穩定性的影響以及在具有不同側壓力系數的地應力場中和、 、類代表性圍巖中軟弱夾層對圍巖穩定性的影響進行了系統的數值試驗，研究得出了軟弱夾層對圍巖位移、拉應力區、塑性區以及噴射混凝土層內力等影響豐富的量化成果，以便直接為工程設計人員提供參考。
  11. In this paper, stress and strain are analyzed in elastic - plastic bending process of plate, and a viewpoint is put forward in with plastic stress and strain neutral layer displace toward inside, and coincide with elastic stress and strain neutral layer when big curvature elastic - plastic bending process is come into being of plate on the basis of the theory of plane curving pole in the material mechanics

    摘要通過對板料彈塑性彎曲應力應變分析，利用材料力學中的平面曲桿理論，提出了板料大麴率彈塑性彎曲塑性應力應變中性層和彈性應力應變中性層均向內移動並重合的觀點。
  12. This paper puts to use a tensile test from the plastic deformation theory, and has deduced the mathematical formulas on determing criterion in the various conditions such as the sotropy and anisotropy materials, plane stress, plane strain, space stress and strain

    文章採用拉伸試驗，根據塑性變形理論，推出了各向同性和各向異性材料在平面應力應變、空間應力應變等多種條件下的判斷準則的數學表達式。
  13. Plastic plane strain

    塑性平面應變
  14. The process of penetration is regarded as expansion of cylindrical cavity in infinite soil mass. combining with the knowledge of elastic mechanics and plastic mechanics, we may make analysis for soil around pile. and we may deduce the cylindrical cavity pressure, radius of plastic zone, radical displacement in elastic zone, and excess pore water pressure in soil around pile and spherical cavity pressure at the end of pile

    本文闡述了樁土共同作用理論原理，對坑式靜壓樁的樁周土體作彈塑性分析，把壓樁過程中樁周土體的本構關系看作是水平面的平面應變小孔擴張問題，利用小孔擴張原理，結合彈性力學以及塑性力學的知識，對壓樁後土體的性狀進行分析，得出樁對土的擠擴作用力、樁周土體塑性半徑、彈性區的位移，以及樁端球形孔擴張的擴張力。
  15. In the fourth chapter, by using the theory of regional potential energy, aiming at the regional layout of international direct investment in china, the author made an analysis on the cause resulting in the nonequilibrium layout of foreign investment and the effects on the changes of regional economic structure caused by the regional layout of foreign investment and forecasted the tendency for importing foreign investment of the provinces, municipalities directly under the central government and autonomous regions. in the conclusion, according to the theory of regional potential energy, the author set forth the law of motion of international direct investment. regional potential energy is determined by the nature, combined mode and development of the elements in the region

    結論部分在總結正文的基礎上，根據區域勢能理論，歸納出國際直接投資的運動規律：區域內備項要素的性質、組合與發展變化決定了區域勢能的大小；而各區域的勢能差異，必然對資本的區域間流動產生強烈的影響，並決定其定向運動的規律；作為經濟發展的關鍵性要素，外資進入后，又將通過區域勢能的激活效應重塑區域社會經濟現實，從總量與結構等各個方面改變區域的發展水平和發展方向，並最終決定新一輪區域勢能的形成及其性質和特點。
分享友人
分享到 Line

分享到臉書