壁厚 的英文怎麼說

中文拼音 [bìhòu]
壁厚 英文
wall thickness
  • 壁 : 名詞1 （墻） wall （of a house etc ） : 銅墻鐵壁 bastion of iron2 （作用像圍墻的部分） wall of st...
  1. Abstract : the paper introduces a kind of method of connecting optimal design of the hydraulic manifolds and establishes the mathematical model based on the constraints of fluxing area and distance between the connecting tubes in the manifolds. a kind of algorithm is provided at the end of it

    文摘:介紹了一種液壓集成塊孔道優化設計方案，建立了以通流面積和壁厚為約束條件的數學模型，並給出了相應的演算法。
  2. If the external dia of shaft liner is big, the wall thickness is high, the tension is also high, so the interference of shaft liner a little low, contrarily, high

    軸套外徑大，壁厚相應加大，壓配合張緊力也大，過盈量可取小些反之，則取大些。
  3. Investigation of thickness variation in t - tube hydroforming

    三通管內高壓成形時壁厚影響因素的研究
  4. Investigation of thickness variation in equal t - tube hydroforming

    等徑三通管脹形時壁厚影響因素的研究
  5. It seems that just by preventing the infarction from growing and by artificially thickening the heart wall in the infracted area, the graft could have helped prevent the usual remodeling of the ventricle

    它的效果看起來比較像避免梗塞部位的擴大，並且增加了梗塞心臟的心室壁厚度，只能說，移植的組織可能防止了心室重塑。
  6. Influence of wall thickness and filling gas procedure on permeability of hollow glass microsphere

    玻璃微球壁厚和預充氣工藝對氣體滲透性能的影響
  7. At the same time, in the field of warm extrusion forming technique for pockety wall thickness forging, the research conclusion of this paper has important leading meaning and application value

    同時，本論文的研究成果對非均勻壁厚鍛件的溫擠壓成形工藝研究有重要的指導意義及實用價值。
  8. The inside fashion of the sway oil pump stator is complex, its wall thickness is pockety and the metal flow law is difficult to master. at the present time, the investigation of warm extrusion forming technique for the nonuniform wall thickness forging has few to been done. the forming technique and die configuration which use for production have not achieve optimization

    由於轉向油泵定子的內部形狀復雜，零件壁厚分佈不均，金屬流動規律難于掌握，目前人們對這種非均勻壁厚鍛件的溫擠壓成形工藝研究幾乎沒有，其成形工藝及生產用模具結構並未達到最優化。
  9. The experimentation of the door outer ’ s viscous pressure forming under different blank holder pressures has been done. the strain distributions of the decorated rib and handle are obtained by the girding method and the thickness strain distributions are also obtained

    通過網格分析法對試件關鍵部位（裝飾筋和把手）的應變進行了分析，分析了粘性介質壓力成形過程中成形試件的壁厚分佈。
  10. Aimed at tube curve by sun shining, it analyzes and calculates the instance of curve when tube up and down face have difference in temperature, and discourses upon it influenced degree to cannon firing accuracy. for hot spread asymmetry caused tube curve, it explains it ' s form cause. for irregularly hot stress acting tube curve, it stressfully analyzes effect of body tube wall thickness difference

    重點分析了身管熱彎曲產生機理，針對太陽照射下的身管彎曲，分析計算了身管上下表面存在溫度差時的彎曲情況，論述了其對火炮射擊精度的影響程度；對于散熱不均引起的身管彎曲說明了其形成原因；對于不規則熱應力作用下的身管彎曲重點分析了身管壁厚差的作用。
  11. During the processes, the container - truck strikes the guardrail twice and nearly capsizes, then recovers from the capsizal and separates from the guardrail ; the crashworthiness of several kinds of guardrails is evaluated by changing its size and thickness, and its design is guided under the simulation result ; the joint simulation is discussed and calculation method of its resistance moment is proposed

    對車輛的碰撞過程進行了描述：車輛在碰撞過程中發生了二次碰撞並且有傾覆現象，最後車輛恢復正位，順利沿護欄導出；通過改變護欄欄桿的尺寸和壁厚，評估了多種護欄的耐撞性並指導了護欄的設計；討論了集裝箱汽車列車鞍座結構的處理，提出了鞍座阻力矩的計算方法。
  12. Moreover, relation between temperature of cold media, freezing time and the thickness of freezing wall is analyzed

    此外，還分析了冷媒溫度、凍結時間和凍結壁厚度的關系。
  13. Taking thickness of web members and main chords as design variables and the lightest weight of crane booms as objective junction, considering constraints of rigidity and stability etc., this paper establishes the math model of optimal design

    摘要選取起重機臂架的腹桿壁厚和各節臂架的主弦桿壁厚為設計變量，以最小重量為優化目標，考慮剛度和穩定性等約束條件，建立優化數學模型。
  14. Road vehicles - open crimp barrels for assembling low - tension cables of thin insulation wall thickness by hand crimping tools

    道路車輛.使用手工壓接工具裝配薄絕緣壁厚度的低張力
  15. On the base of the basic structure study of the tooth - locked quick closure vessel of middle and low pressure with crown head, the optimization method of parameterized whole device is presented in this paper, the emphases of research is put on optimization of the tooth - locked quick closure device whose structure and load distribution is complicated, the wall of vessel, however, is designed according to the existing strength formula

    本文對帶有球冠形封頭的中、低壓齒嚙式快開容器的基本結構進行研究的基礎上，提出了齒嚙式快開容器的參數化整體優化方法，研究重點放在結構和受力復雜的齒嚙式快開裝置的優化，對于容器簡體壁厚仍採用現有強度公式設計。
  16. These are formed from a zone containing larger vessel elements produced by the cambium in the spring ( lighter layer ), followed by a zone containing smaller vessel elements ( darker layer ) produced during the late summer

    春季，形成層活動旺盛，形成的次生木質部細胞，管徑大而壁厚，色澤較淡；夏末，形成層活動逐漸減弱，形成的次生木質部細胞，管徑小而壁薄，色澤較深。
  17. Through developing the comprehensive experiment device with large - scale drum strength and stability, the stress - measuring experiments of various wall thickness of the normal drums of the cranes were performed. the law that the stress of the drums along the circumference and along the axis changes with the load increase of the wire ropes was studies for the first time

    通過研製全比尺大型捲筒強度、穩定性綜合試驗裝置，對起重機常用規格的捲筒進行了各種壁厚條件下的應力測量試驗，首次對捲筒體周向和軸向應力隨鋼絲繩逐步加載過程變化的規律進行了研究，發現最大應力產生在鋼絲繩繞過后3 ~ 5圈截面處，該現象與理論分析結果也是符合的。
  18. The tests were conducted in the hypersonic low density wind tunnel at nominal test conditions of mach 16, stagnation temperature 923k, stagnation pressure 1. 40mpa and 7. 30mpa. heat - transfer data were obtained on a hemisphere model, a sharp cone and a big blunt cone respectively by means of infrared thermal mapping techniques, that of a 0. 5mm thickness blunt cone by virtues of thermocouples. furth ermore, heat - transfer on all those models was calculated with the theoretical method

    最後在名義m _ = 16 、 t _ 0 = 923k 、 p _ 0 = 1 . 40mpa及7 . 30mpa的高超聲速低密度風洞中，利用紅外熱圖技術獲得了半球圓柱、尖錐、大鈍頭三個模型表面熱流分佈，利用薄壁法技術得到了一壁厚為0 . 5mm的鈍錐模型表面的熱流分佈，並通過工程理論方法計算了模型表面的氣動熱，把理論計算結果與上述試驗結果比較，幾者符合得較好。
  19. Abstract : described in the paper is the result of tianjin steel tube corporation ' s applying the latest on - line gauging system i. e. the steel tube isotope thermal gauging system to the mpm line, involving details of several typical thermal gauging curves

    文摘:介紹了天津鋼管公司在其mpm連軋管機組上應用新一代在線測厚系統? ?鋼管同位素熱測壁厚儀的成果，並較為詳細地介紹了幾個典型的熱測壁厚曲線圖。
  20. The influence of nondimensional parameters and on failuremode and ultimate tensile strength of gusset plate connections to slotted tubes arestudied

    、鋼管直徑與鋼管壁厚之比?對該類節點破壞模式和極限承載力的影響。
分享友人
分享到 Line

分享到臉書