壓制梁 的英文怎麼說
中文拼音 [yāzhìliáng]
壓制梁
英文
formed beam-
Research of piezoelectric control techno logy for active vibration control of fl exible beam
柔性梁振動主動控制的壓電控制技術研究Mode control of vibration in piezoelectric cantilever beam
壓電懸臂梁振動的模態控制5 ) processing the active vibration control examination of piezoelectricity material cantilever beam model part with the pid control and the lqg control
5 ）分別採用pid控制和lqg控制進行了壓電貼片懸臂梁模型振動主動控制試驗。The paper introduces the construction technique and quality control of the concrete ground container, the project uses the small machine - constructing method which vibrates beam and the vibrating spear unify, through example of key working procedure : the construction survey, the ground basic roller compaction, two ash zone constructions, the steel bar construction, the template construction, the concrete surface layer construction craft and the quality control, the small machine construction method prove to meet the project needs
摘要介紹了混凝土集裝箱堆場施工工藝與質量控制，工程採用振動梁和振動棒相結合的小型機械法施工，通過對關鍵工序如：施工測量、場區基層碾壓、二灰層施工、鋼筋施工、模板施工、混凝土面層的施工工藝與質量控制，表明小型機械法施工能滿足工程需要，工程完成後符合驗收標準，滿足了業主的使用要求，對于同類工程的施工具有借鑒意義。Then the judging method is proposed, and the proposed method can consider the stress history and viscosity shear strength of soft soil. in this paper, a fem program dpfbm1. 0 ( double plastic foundation beam method ( version 1. 0 ) ) is established. with this program, the influence of some parameters on foundation excavation is fully studied, the parameters include : compression modulus, cohesive strength, angle of internal ficiction, effective angle of internal friction, the embedded length of the wall and building load
針對當前國內外彈性地基梁法存在的缺陷，基於對軟土流變性的研究，採取了剪應力判斷彈塑性狀態，以改進和完善基坑工程彈性地基梁法，推導了彈性狀態下地基反力系數的近似解，提出了採用剪應力組合判斷土彈簧彈塑性狀態的方法，編制了相應的彈塑性共同變形法分析程序dpfbm1 . 0 （ doubleplasticfoundationbeammethod （ version1 . 0 ） ） ，並採用該程序分析了壓縮模量、粘聚力、內摩擦角等參數變化對基坑工程的影響。This paper sets up a fuzzy optimum math - model of the prestressed degree for prestressing bundle disposition of prestressed concrete continuous beam bridges, which is transformed into a clear math program by - level cut - set. by the solution of the clear math program, a succession of reasonable prestressing moments can be obtained. then it is convenient to dispose the prestressing system by only taking account of geometric factors of all controlling sections. based on this, a theory of automatic disposition of the prestressing bundles is proposed and an engineering example is given to demonstrate it
建立預應力混凝土連續梁橋預應力度的模糊優化問題，按-水平截集解法，將模糊優化問題轉化為確定性的數學規劃問題.求得一較合理的消壓彎矩后，只需按控制截面的構造進行預應力體系設計.在此基礎上提出了配束自動化的基本思想，並以一實例說明其理論應用Abstract : this paper sets up a fuzzy optimum math - model of the prestressed degree for prestressing bundle disposition of prestressed concrete continuous beam bridges, which is transformed into a clear math program by - level cut - set. by the solution of the clear math program, a succession of reasonable prestressing moments can be obtained. then it is convenient to dispose the prestressing system by only taking account of geometric factors of all controlling sections. based on this, a theory of automatic disposition of the prestressing bundles is proposed and an engineering example is given to demonstrate it
文摘:建立預應力混凝土連續梁橋預應力度的模糊優化問題，按-水平截集解法，將模糊優化問題轉化為確定性的數學規劃問題.求得一較合理的消壓彎矩后，只需按控制截面的構造進行預應力體系設計.在此基礎上提出了配束自動化的基本思想，並以一實例說明其理論應用In this paper, at the cut - in spot of beam active vibration control and use the pzt material as the drive component, the main research works can be summarized as follows : 1 ) using the finite element theory, a general finite element formulation of piezoelectric media is derived, the direct and converse piezoelectric effects are considered in the formulation
本文從梁的振動主動控制研究為切入點，利用了pzt材料作為驅動元件，作了如下幾個方面的研究： 1 ）利用有限元理論，考慮壓電材料的正、逆壓電效應的影響，導出了機電耦合壓電元件的有限元方程。Five eyes ( 16 % ) developed chronic angle closure glaucoma due to peripheral anterior synechia. one could be controlled by chronic medical therapy, three required trabeculectomy, the another one even required cyclocryotherapy because poor iop control after trabeculectomy
5隻眼（ 16 % ）因周邊前黏連發生慢性隅角閉鎖性青光眼，其中1隻眼可以藥物控制， 3隻眼需做小梁切除術，另1隻眼做小梁切除術后眼壓仍無法控制而接受睫狀體冷凍治療。Electro - hydraulic servo control ' s technology becomes an important constitute of modern time control technology as a bridge between the micro - electronics, computer technology and electro - hydraulic control technology. for electro - hydraulic servo control ' s technology has the advantage of fine linearity, little deadband, high sensitivity, fine dynamic performance, rapid respond, high precision and so on, it is used in many fields
電液伺服控制技術作為現代微電子技術、計算機技術和液壓技術的橋梁，已經成為現代控制技術的重要組成部分。由於它具有線性好、死區小、靈敏度高、動態性能好、響應快、精度高等顯著優點，因而得到了廣泛的應用。Based on measurement of strains of both horizontal stirrups in the joint core and longitudinal reinforcement passing througth the joint, in different stages, transfer mechanism and factors affacting seismic behavior of the joint, were analysed. under different shear compression ration, effect of axial force ratio on seismic behawior of the joint was also evaluated, static shear and seismic shear of the joint based on capacity design were investigated. on this basis, new governing criteria and conditions of seismic behavior of the joint were put forward
通過對節點區水平箍筋以及貫穿節點梁、柱縱筋在不同受力階段應變的精細量測，對節點的傳力機理以及影響抗震性能的因素進行了分析研究；對不同剪壓比條件下軸壓比對節點抗震性能的影響規律進行了分析研究；對不同受力階段梁筋的粘結退化規律以及節點區的剪切變形進行了分析研究；對節點的靜力抗剪與建立在能力設計思路上的抗震抗剪問題進行了深入研究，提出了建立在新思路基礎上的節點抗震性能控制準則和控制條件。In order to make the sensitivity of 2 - demension accelerometer along the two main arbors almost identical, symmetric four - beam structure that embeds a double - sides interdigitated differential capacitive with puckered beam in two directions was used as sensitive component. in addition, the differential capacitive accelerometer fabricated by bulky silicon micromechanical technique has high sensitivity, wide measurement scope, less nonlinear error, and simple converting circuit. then, the structure parameters of the sensitive component were calculated and stimulated, which results in a set of the optimized structure design parameters, main fabrication procedure and several key fabrication technology
為使二維振動傳感器在兩主軸方向的靈敏度大致相同，敏感元件採用高度對稱的四梁結構，其中每個軸向上均採用帶折疊梁的雙側叉指電容結構，採用體硅微機械工藝製作的高深寬比叉指電容式敏感元件，具有高靈敏度、寬量程、非線性誤差小、外圍電路簡單等優點;對設計的敏感元件結構參數進行了計算，並利用有限元法進行了模擬分析，根據模擬結果得出了優化參數;在確定敏感結構的基礎上，研究了敏感元件採用體硅微機械加工工藝製作的工藝流程和關鍵工藝技術;對敏感晶元內部的c - v介面電路進行了原理設計與分析，利用差動測量技術得到由振動引起的微小電容變化量，經c - v介面電路進行相位調制處理，然後通過解調輸出與加速度成正比的電壓信號。Rigid - flexible coupling system ; rotating flexible beam ; active vibration control ; positive position feedback ; piezoelectric ceramic
剛柔耦合系統旋轉柔性梁振動主動控制位置正反饋壓電陶瓷Hydraulic pile hammer is one of the pile driving machines that drive prefabricated piles into the ground in the construction of pile foundation such as construction, bridge, dock, etc. with the development of science and technology, the prefabricated pile driving machines evolve from block hammer, steam - hammer, diesel hammer to hydraulic hammer. hydraulic pile hammer is one of ideal prefabricated pile driving machines because it can adjust stress waveform, decrease stress peak value, prolong effectual action when it drives piles. hydraulic pile hammer is used widely and formed series in developed countries now
液壓打樁錘是用於建築、橋梁、碼頭等樁基礎施工中打入預制樁的樁工機械。隨著科學技術的進步，預制樁施工機械由落錘、汽錘、柴油錘，發展到了液壓打樁錘。用液壓打樁錘打樁，可以調整撞擊應力波波形，減小應力峰值，延長有效作用時間，是一種比較理想的預制樁施工機械，目前在發達國家已被廣泛使用，並形成了系列化。Active control of piezoelectric composite beam vibration using a nonlinear fuzzy filter
壓電復合材料層合梁非線性模糊濾波振動控制Fabrication of the box beam is divided into such parts as reinforcement, formwork, concreting, prestressing, moving and storing of beam, pipe grouting under pressure, end sealing of the beam, water - proof layer on the bridge surface system, protective coating etc. the paper makes description of effective box beam construction technology and workmanship which can be adopted in other projects, such technologies as : manufacturing and fixing of reinforcement, steel reinforcement fixing baseplate, web plate and top plate respectively and lifting the steel skeleton into form, requirements of design and manufacturing and way of utilization for dismantling - erection type formwork and hydraulic formwork, optimization of concrete ratio, concrete pouring process of two ends of beam in priority over the middle, in sequence of first baseplate followed by web plate and top plate at last, concrete pouring in inclined section and in horizontal layer, concrete vibration mainly by external vibrator in assistance with internal vibrator, methods and regulation for steam curing of concrete, dual controls over stress and strain to ensure quality of prestressing workmanship, construction method of effective beam moving by heavy - weight special moving facility, some regulations and key notes about construction of grouting under pressure, beam ends sealing, water - proof layer on the bridge surface system, protective coating
箱梁製造由鋼筋工程、模板工程、混凝土工程、預應力工程、移存梁工程、孔道壓漿工程、梁體封端工程、橋面防水層和保護層工程等施工環節組成。文中介紹的採用胎具製作和綁扎鋼筋，分底腹板和頂板分別綁扎並吊裝鋼筋骨架入模；拆裝式和液壓式兩種模板的設計、製作要求和使用方法；綜合考慮、優化混凝土配合比，混凝土灌注從兩端至中間、先底板、后腹板、再頂板的施工順序和斜向分段、腹板水平分層、附著式振搗為主、插入式搗固為輔的施工工藝，蒸汽養護的方法和規定；應力應變雙控制確保預應力施工質量的施工技術；採用重物移運器有效移梁的施工方法；壓漿、封端、橋面防水層和保護層施工的一些規定和注意事項等都是對箱梁製造行之有效的施工技術和施工方法，並可為以後類似施工作借鑒。Vibration control of cantilever beam using self - sensing actuator
基於壓電自感知執行器懸臂梁振動控制Abstract : this paper introduces the global stiffness, strength and stability of bracing structure with long span, pointing out that the control of bracing structure ' s deflection and elastic module can make the arch ring fit the line of pressure and arch axis and can guarantee the stability of bridge structure
文摘:本文介紹了大跨度支撐結構的整體剛度、強度和穩定性，控制支撐的撓度和彈性變量可使拱圈符合設計壓力線與拱軸線，保證橋梁結構的穩定性。With reference to the cantilever erection of the continuous steel box girder of zhuanxing road overhead bridge crossing shenfengjin expressway in shanghai, this paper mainly describes the application of plc - controlled hydraulic sync jack - up system to the balanced cantilever erection of the box girder, closure construction of the girder at midspan, and the operation, control key points and corresponding technical requirements for application of the system
摘要結合上海莘奉金高速公路顓興路跨線連續鋼箱梁懸臂架設施工，重點闡述了plc控制液壓同步頂升系統在鋼箱梁「對稱懸拼，跨中合龍」中的應用及操作控制要點、技術要求。The whole piezolaminated curved beam is equivalent as a single layer structure, and the governing equation of piezolaminated curved beam with small curvature is derived based on one - dimensional beam theory
將壓電夾層圓形曲梁等效為單層結構，基於一維小曲率曲梁理論，建立其控制方程。分享友人