壓製法 的英文怎麼說

中文拼音 [yāzhìfǎ]
壓製法 英文
continuous compacting process
  • 壓 : 壓構詞成分。
  • 法 : Ⅰ名詞1 （由國家制定或認可的行為規則的總稱） law 2 （方法; 方式） way; method; mode; means 3 （標...
  1. Back covered porous brick has been developed in the late period of 1990 ' s, and is produced by semi - dry - pressing method. it has such many advantages as high production efficiency, energy saving, high density, beautiful appearance, high strength, easy bricklaying, and can save 1 / 3 masonry mortar compared with solid brick

    盲孔多孔磚是20世紀90年代後期研製成功的、用半干壓法壓製成型的封底多孔磚，它生產效率高，節約能耗，產品緻密，外形好，強度高，易砌築，用於砌體工程時，可節約1 3砂漿。
  2. In the end, the stability is discussed under the coulomb friction model, getting the normal force compensation method and the additive vibration control method, which are to stabilize the friction drive system to realize the controllability and stability, which is simple to realize in the micro manipulator

    並通過對coulomb摩擦模型的穩定性討論，得出正壓力補償控製法，即以穩定摩擦力驅動摩擦振子實現微操作手運動的可控性及穩定性的方法分析。通過數值方法驗證正壓力補償控製法的適用性，為微操作器的運動控制提出可行方法。
  3. Method of grading control for detection of subgrade compactedness

    路基壓實度檢測的級配控製法
  4. Elastic rubber method and rigid blank holders were used to apply blank holder force with different methods

    對壓邊力的控制採用了彈性橡膠控制和剛性直接控製法。
  5. Abstract : six methods for making preparation of chromosomes of spiders, including gonad slice technique, testis squash technique, single embry drop technique, mix embryo - cells drop technique, blood cell drop technique and single embryo - cell squash technique, are summarized in this paper. the karyotypes of 27 species from 22 genus in15 families are analysed

    摘要概述了蜘蛛染色體製片的6種方法：生殖巢切片法、精巢壓片法、單胚滴片法、混合胚滴片法、血細胞製片法和單一胚胎壓片法，並總結分析了蜘蛛目15科22屬27種染色體核型。
  6. At the same time, vcvs ( voltage - controlled - voltage - source ) is presented in this paper to reflect the actual situation exactly

    同時，本文提出電壓控制電壓源的輸入信號控製法，精確地反映了實際工作的情況。
  7. The paper analyzes the non - lineal relations of the quantity of heat exchange and water flux of coil exchanger in part - load operating condition, the shortage of deciding the water flux in bypass pipe, the disadvantage that the operating condition of pumps and chiller ca n ' t be met with the load change of the air conditioning system in different operating condition of using pressure - difference bypassing control in primary water pump system. using load control method in the change of the operating condition of primary water pump system can realize that the load change is small and reasonable in the on / off condition of pumps and m m chiller by comparing load control method in primary variable - flow water pump system with pressure - difference bypassing control method, back water temperature control method

    本論文從目前空調工程中使用的變流量水系統入手，研究了盤管換熱器在部分負荷下水流量與換熱量的非線性關系，分析了文獻中介紹的旁通管通流能力選擇的不足之處和一次泵水系統採用壓差旁通控制時，工況轉換不能滿足系統控制要求的缺陷；比較了一次泵變流量水系統中壓差旁通控製法、回水溫度控製法、負荷控製法的精確性，並得出了在一次泵水系統的工況轉換時，採用負荷控製法能使冷水機組及其相應水泵在啟停時的負荷變化范圍較小，更符合建築物的冷量需求，節能效果較好的結論。
  8. We produce a high strength titanium alloy by means of an original roll method

    通過獨特的輥壓方法製造的高強度的鈦合金m8法蘭螺絲
  9. Standard test method for short - beam strength of polymer matrix composite materials and their laminates

    聚合母體組合材料及其層壓製件的短梁強度的標準試驗方法
  10. Novel current modulation approach for the vector control of mc - pmsm system

    一種減少矩陣變換器共模電壓的空間矢量調製法
  11. Plastics. determination of environmental stress cracking. ball or pin impression method

    塑料製品.環境應力開裂測定.球體或銷針壓痕法
  12. Rigid polyurethane foam produced by the press injection method - specification for pur foam for insulated panels for transport containers and insulated vehicles bodies

    採用壓注法製作的聚氨酯硬泡沫塑料.第1部分:運輸集裝箱和車身用隔離板的聚氨酯硬泡沫塑料規范
  13. Based on the investigation with several voltage control methods, such as venturini method, instantaneous double - voltage synthesis method and space vector modulation method ( svm ), three new control strategies are put forward. firstly, a time - varying modulation coefficient svm method is proposed to improve mc ' s anti - disturbance performance under the asymmetry input voltage. secondly, a 5 - state switching strategy is presented for mc controlled by the svm method, which reduces the commutation number and switching losses remarkably

    在分析了venturini控製法、瞬時雙電壓法、空間矢量法等電壓控制方法的基礎上，提出了在非對稱輸入條件下矩陣變換器空間矢量法的時變調制比改進控制策略，提高了變換器的抗干擾性能；對空間矢量法的開關策略進行了研究，提出了新型5狀態開關策略，在保證其他性能不受影響的條件下，減少了變換器的換流次數和開關損耗；提出了一種矩陣變換器單電壓合成的新方法，它不僅使得變換器的控制簡單，計算量減少，而且使得開關損耗達到最少。
  14. After several typical foreign desktop systems had been studied, mem ( melted extrusion manufacturing ) process was chosen as the molding process of the first rapid prototyping desktop system in china, mem200 - d, which combined our technical advantages and design experiences. by using the mechatronic design and modularization method, the system scheme design, layout design and part / assembly design have been achieved

    作者在研究了國外多種典型的桌面化快速成形系統的工藝、特點之後，結合自身的技術優勢和設計經驗，選擇熔融擠壓製造工藝（ meltedextrusionmanufacturing ，簡稱mem ）作為國內第一臺桌面化快速成形系統mem200 - d的成形工藝，同時應用機械電子學產品設計方法，結合桌面化快速成形系統的特點，以模塊化設計思想完成了mem200 - d桌面化熔融擠壓成形系統的總體方案設計、結構布局設計和零部件設計。
  15. Plastics - determination of hardness - part 1 : ball indentation method

    塑料製品.硬度測定.第1部分:壓球法
  16. Standard test method for comparison of bond strength or ply adhesion of similar laminates made from flexible materials

    撓性材料制類似層壓製品的粘結強度或層間粘結度比較的試驗方法
  17. It is proved that variable capacity of mixture has obvious advantages comparing to limitative composition systems of pure substance and mixture, and it is a feasible method by controlling low pressure, which can be used to vary mixture composition. 4

    得出相對于純質和定比例混合工質系統而言，變濃度混合工質系統具有明顯的優勢，以及採用吸氣壓力控製法來改變混合工質的濃度配比是可行的。
  18. In condusion, the research of rotating converter will promote the progress of the synchronous generator brushless excitation system and illuminate a new direction of the power electric converter

    為減少旋轉變壓器的散磁和漏磁，改善其性能，本文使用了新型的變壓器繞制方法?平面繞製法。
  19. In this paper, aluminum foams with 40 % - 80 % porosity. 2 - 5mm pore diameter, and 0. 4 - 0. 6 restive density, were produced by the p / m method, i. e. by mixing 6061 powders and blowing agents and pressing them to densification, then foaming

    本論文闡述了粉體發泡法制備泡沫鋁的工藝，即把少量的發泡劑（ tih _ 2粉末）和6061鋁合金粉末混合均勻，然後壓製成試樣，再進一步熱壓，最後在金屬基體熔點附近發泡。
  20. This paper explored the micro pressure sensor that is used for the measurement of distributed pressure at the surface of smart - skin. firstly, established the surface pressure model according to the aerodynamic properties, defined the optical measurement system that based on intensity modulation principle, discussed the components of this system and theoretical analyzed its measurement theory in detail

    首先，根據空氣流動的基本規律給出機翼表面壓力分布圖，通過對光學式微型壓力傳感器的理論分析，採用強度調製法測量飛機機翼表面的壓力並建立基於此方法的光學測量系統模型，得到了壓力與敏感膜片變形以及光電轉換輸出能量之間的關系。
分享友人
分享到 Line

分享到臉書